Manual do usuário Black Box ME800A

Manual para o dispositivo Black Box ME800A

Dispositivo: Black Box ME800A
Categoria: Equipamentos de rede
Fabricante: Black Box
Tamanho: 0.1 MB
Data de adição: 1/27/2014
Número de páginas: 27
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Black Box ME800A. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Black Box ME800A.

Para sua conveniência

Se a consulta dos manuais Black Box ME800A diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Black Box ME800A no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Black Box ME800A em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Black Box ME800A Manual de instruções - Online PDF
Advertisement
« Page 1 of 27 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Black Box ME800A, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Black Box ME800A. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

AUGUST 2000
ME800A
ME800A-R2
ME805-C
ME805-C-R2
ME810
Short-Haul Modem B
(SHM-B Async)
CUSTOMER SUPPORT INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
NORMAL
TD RD
LOOPBACK
ASYNC SHORT HAUL MODEM

Resumo do conteúdo contido na página número 2

SHM-B ASYNC FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which

Resumo do conteúdo contido na página número 3

SHM-B ASYNC NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas. 4. Todas las instrucciones de operación y uso deben ser seguidas. 5. El aparato el

Resumo do conteúdo contido na página número 4

SHM-B ASYNC 10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores) que producen calor. 11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como se indique en el aparato. 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente

Resumo do conteúdo contido na página número 5

SHM-B ASYNC TRADEMARKS USED IN THIS MANUAL Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. 4

Resumo do conteúdo contido na página número 6

SHM-B ASYNC 1. Specifications Transmission — Data Rate (bps) Distance (miles/km) 19,200 1/1.6 9600 2/3.2 4800 3/4.8 2400 4/6.4 NOTE:The above specifications are valid for 24- or 26-AWG unshielded twisted-pair telephone cable insulated by polyethylene with a mutual capacitance of 0.083 µf/mile. Shielded twisted-pair cable will reduce the distance to one-third of the table value, due to the additional capacitance contributed by the cable’s shielding. Actual distances may vary depending on your sp

Resumo do conteúdo contido na página número 7

SHM-B ASYNC end of the loop. Interface is switch-selectable for DTE/DCE configuration (pins 2 and 3 are reversed) Connectors — (1) DB25 female, (1) 5-screw terminal block Diagnostics — Loopbacks provided by a front-panel switch: Analog loopback on a 4-wire loop and digital loopback on equipment interface (EIA-232) Status Indication — Two bi-color LEDs indicate the status of the transmitter and receiver. A green light indicates a “low” logic level (-3 to -25V) on the EIA-232 interface; a red ligh

Resumo do conteúdo contido na página número 8

SHM-B ASYNC Primary: 115 VAC ±10%, 60 Hz, 5 watts (12 watts max.); Primary: 230 VAC ±10%, 50/60 Hz; Secondary: 17 VAC, 700 mA Size — Standalone: 1.4"H x 4.25"W x 4.5"D (3.8 x 10.9 x 11.7 cm); Rackmount: 5.25"H x 17"W x 9"D (13 x 43 x 23 cm) Weight — Standalone: 1.3 lb. (0.6 kg), including transformer; Rackmount: 3.7 lb. (1.7 kg), including transformer 7

Resumo do conteúdo contido na página número 9

SHM-B ASYNC 2. Introduction The Short-Haul Modem Model B Async (SHM-B Async) is an asynchronous full-duplex 4-wire line driver/receiver which allows two EIA-232 devices to communicate at distances of up to 4 miles and at data speeds of up to 19,200 bps. In addition to the transmitter and receiver circuits, the SHM-B Async includes EIA-232 control line interfaces, status monitor LEDs, and a loopback switch. The SHM-B is available in both a standalone version (ME800A) and a rackmount version (ME80

Resumo do conteúdo contido na página número 10

SHM-B ASYNC 3. Installation Installation involves three basic steps: four-wire connections; EIA-232 connection; switch settings. 3.1 Four-Wire Connections Figure 1 shows the location of the terminal block on the circuit board. Refer to Figure 2 to make the proper connections between two SHM-B units. NOTE: Transmit + (TX+) on one modem is wired to Receive + (RX+) on the other modem; Transmit - (TX-) is wired to Receive - (RX-). A ground connection is optional. 1. If the unit is assembled, separat

Resumo do conteúdo contido na página número 11

RX+ RX- TX+ TX- GROUND SHM-B ASYNC 5. Insert the wires into the terminal strip; tighten the screw terminals. 6. After you have made all four connections, wrap the nylon cable tie (packaged with the SHM-B) around the wires. Pull the tie tight around the wires to secure them to the printed circuit board. Trim the excess nylon tie with wire cutters or scissors. J1 RS-232 CONNECTOR EN JUMPER DIS RTS/DTR DCE CONTROL DTE/DCE DTE S2 (LOOPBACK) Figure 1. SHM-B board; 5-screw terminal block. 10

Resumo do conteúdo contido na página número 12

SHM-B ASYNC TX+ RX+ TX- RX- RX+ TX+ RX- TX- SHM #1 SHM #2 Figure 2. Wiring diagram for two SHM-B units. 3.2 EIA-232 Connection Connect the SHM-B to your computer or terminal with a standard EIA-232 cable and DB25 connectors. Refer to your equipment’s installation manual if you need information on the exact EIA-232 signals required for your equipment. Often, it is best to use only the Transmit Data (TD), Receive Data (RD), and ground lines if your equipment does not require the use of the control

Resumo do conteúdo contido na página número 13

SHM-B ASYNC Table 1. EIA-232 Pin Connections on SHM-B Pin Number Signal Name 1 Protective Ground 2 Transmit Data/Receive Data (TD/RD)* 3 Receive Data/Transmit Data (RD/TD)* 4 Request to Send (RTS) 5 Clear to Send (CTS) 6 Data Set Ready (DSR) 7 Signal Ground 8 Carrier Detect (CD) 20 Data Terminal Ready (DTR) *TD and RD can be reversed using the DTE/DCE switch, S1 on the circuit board. See Section 3.3 for details. 3.3 Switch Settings Refer to Figure 1 in this chapter. Switch S1 is used to reverse

Resumo do conteúdo contido na página número 14

SHM-B ASYNC information concerning its DTE/DCE setting. Table 2 gives the EIA-232 pinning of the SHM-B with the DTE/DCE switch in the DCE position. Table 2. Pinning with DTE/DCE switch in the DCE position. PIN NUMBER SIGNAL NAME DIRECTION 1 Protective Ground ————— 2 Transmitted Data TD* To DCE 3 Received Data RD* From DCE 4 Request to Send (RTS) To DCE 5 Clear to Send (CTS) From DCE 6 Data Set Ready (DSR) From DCE 7 Signal Ground ————— 8 Received Line Signal Detector From DCE 20 Data Terminal Re

Resumo do conteúdo contido na página número 15

SHM-B ASYNC 3.4 Flow Control The SHM-B uses a clever, yet simple way to allow this unit to work with a broad line of equipment. STANDARD EIA-232C HANDSHAKING (RTS/DTR CONTROL JUMPER IN EN POSITION) The individual SHM-B modems force their own DTR, RTS, CTS, and DSR control lines HIGH (>+3V) when: • The twisted-pair wires are installed correctly. • Power is applied to both modems. • No computer devices are attached to the modems. This forces DCD HIGH on the remote modem; thus, the remote modem kno

Resumo do conteúdo contido na página número 16

SHM-B ASYNC Because DTR, DSR, RTS, and CTS are tied together internally, dropping any one of these four signals to a negative state will also drop DCD on the remote side to a negative state. DCD will also go LOW if the remote SHM-B is powered down, or if the twisted-pair wire is broken. X-ON/X-OFF MODE (RTS/DTR CONTROL JUMPER IN DIS POSITION) If X-ON/X-OFF characters are used for handshaking control, rather than hardware logic levels, move the RTS/DTR control jumper to the DIS position. Typicall

Resumo do conteúdo contido na página número 17

SHM-B ASYNC 4. Operation After completing the wiring and configuration procedure, slide the printed circuit card back into the case while pulling the data and power cables through the holes in the back panel. The front panel will snap into the front of the case when the printed circuit board has been completely pushed to the back of the case. Connect the SHM-B to your equipment, then plug the wall transformer into its power source. Check the SHM- B operation at both ends of the loop by pressing

Resumo do conteúdo contido na página número 18

SHM-B ASYNC When in loopback mode, the switch button indicator will appear to the sender. If a CRT terminal is connected to the SHM-B, typing characters on the keyboard should result in the same characters appearing on the CRT screen. If no characters appear, check your EIA-232 connections and the setting of S1. See Figure 3 for an illustration of the loopback mode. The TD and RD LEDs on the front panel of your SHM-B indicate the status of the SHM-B transmitter and receiver, respectively. Green

Resumo do conteúdo contido na página número 19

SHM-B ASYNC 5. Rackmount Installation The SHM-B Async Card is a rack mount unit (ME805-C) that installs in a standard 19-inch panel rack. (You can use the SHM-B Rack [ME810], which can hold up to 16 cards.) The SHM-B Async Card will occupy 5.25 inches of vertical rack space, and is 9 inches deep. To install the SHM-B Rack, first remove the acrylic front panel by pulling out the six plunger latches on the front of the panel, then pulling on opposite-side plungers to loosen and remove the panel. L

Resumo do conteúdo contido na página número 20

SHM-B ASYNC easiest access to the terminals, switches, etc. After a SHM-B Card is wired, it can then be inserted into an open slot in the SHM-B rack. Be certain that the circuit board has mated with the power pins on the SHM-B rack before applying force to fully seat the board; otherwise you may damage the board and power pins. When all boards have been wired and plugged into the rack, plug the wall transformer into its power source. You should be able to communicate as described in Chapter 4. W


Manuais similares
# Manual do usuário Categoria Baixar
1 Black Box 8-/16-/24-Port 10/100 PoE PSE Web Smart Switch Manual de instruções Equipamentos de rede 0
2 Black Box 10Base-T Transceiver Stand-Alone model Manual de instruções Equipamentos de rede 2
3 Black Box AC1132A Manual de instruções Equipamentos de rede 1
4 Black Box 24+4-PORT GIGABIT SWITCH MANAGED W/4 SFP + 10G Manual de instruções Equipamentos de rede 0
5 Black Box 10/100BASE-T Ethernet Extender over VDSL2 Manual de instruções Equipamentos de rede 2
6 Black Box 2-Port and 4-Port Audio/Video Splitters Manual de instruções Equipamentos de rede 0
7 Black Box 8x8 DVI-D Matrix Switches Manual de instruções Equipamentos de rede 0
8 Black Box AC150A-4 Manual de instruções Equipamentos de rede 0
9 Black Box 4-Port RJ-45 Modem Splitter (RS-232 on RJ-45) Manual de instruções Equipamentos de rede 3
10 Black Box AC151AE-REM Manual de instruções Equipamentos de rede 0
11 Black Box AC650A-2 Manual de instruções Equipamentos de rede 1
12 Black Box AC650A-4 Manual de instruções Equipamentos de rede 0
13 Black Box ACR1000A-CTL Manual de instruções Equipamentos de rede 0
14 Black Box AC151A-REM Manual de instruções Equipamentos de rede 0
15 Black Box AC650A-2-UK Manual de instruções Equipamentos de rede 0
16 Sony DDU1681S Manual de instruções Equipamentos de rede 0
17 Sony VGP-MR200U/E Manual de instruções Equipamentos de rede 1
18 Sony DDU1681S-0B Manual de instruções Equipamentos de rede 1
19 Sony NAC-SV10I Manual de instruções Equipamentos de rede 9
20 Sony NAC-SV10i Manual de instruções Equipamentos de rede 0