Resumo do conteúdo contido na página número 1
155" (6%") MODEL 1805B
INSTRUCTION MANUAL
DOUBLE
INSULATION
S P EC I F I CAT I 0 NS
Planing
Planing AMPS No load Overall Net Power
width
depth (115Vl speed length weight supply cord
155" 2mm 15,000 529 mm 8 kg 5m
(6-1/8") (5/64") 0'5 A Rlmin. (20-7/8") (17.6 Ibs) (16.4 ft.1
Resumo do conteúdo contido na página número 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of flammable liquids or
Resumo do conteúdo contido na página número 3
of moving parts, breakage of parts, mounting, and other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Don't use tool if switch does not turn it on and off. 19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded sur- faces. For example; pipes, rad
Resumo do conteúdo contido na página número 4
HOW TO USE 1. Planing depth (cutting volume) may be adjusted as desired by simply turning the knob (front grip) on the front of the power planer. 2. To start the tool, simply pull the trigger. Release the trigger to stop. For contin- uous operation, just pull the trigger and then push in the lock button with your thumb. To stop the tool from the lock position, just pull the trigger again and release it. 3. After you switch on the tool by pulling the trigger, wait until the planer is ru
Resumo do conteúdo contido na página número 5
REPLACING OR INSTALLING PLANER BLADES After unplugging the tool, you may remove the planer blades on the tool drum by un- screwing the four installation bolts with the socket wrench provided. The clamp plate comes off together with the blades. (See Photo) Fig. 3 When you install new or sharpened blades, Hex. flange hd. bolt I first clean out all chips or foreign matter adhering to the drum or blades. Use blades of the same dimensions and weight, or drum oscillation/vibration will r
Resumo do conteúdo contido na página número 6
Adjusting blade gauge itself t , n Constant use of a blade gauge leads to wear on the inside flank, resulting in improper settings. To compensate for this, the blade gauge itself must be adjusted. If, for ex- ample, you notice that the blade is below the level of the rear shoe, you probably are not able to actually plane - so the blade / Adjusting screw must protrude more. But, if turning the Fig. depth knob all the way fails to make the blade protrude sufficinetly for planing, th
Resumo do conteúdo contido na página número 7
SHARPENING PLANER BLADES Although a power planer considerably out- performs an ordinary hand plane, by the same token the blades become dull faster. Always keep your blades sharp for the best performance possible. Use the sharpening holder (photo) to remove nicks and pro- duce a fine edge. Sharpening holder Fig. 7 First, loosen the 2 wing nuts on the holder Wing nut and insert blades A and B as in figure at right, so that they contact side C and D. Then tighten wing nuts. Side (CJ
Resumo do conteúdo contido na página número 8
ACCESSORIES CAUTION : The accessories specified in this manual are recommended for use with your Makita Power Planer. The use of any other accessory might be hazardous. Replacement Blades Planer Blades (Part No. 731010-3) (Material : Tungsten-carbide) (Part No. 731204-0) Sharpening Holder Dressing Stone (Part No. 123006-2) (Part No. 741801-4) Blade Gauge Bevel Guide (Part No. 123009-6) (Part No. 123053-3) Socket Wrench (+) Screwdriver (Part No. 782209-3) (Part No. 783002-8) Wooden C
Resumo do conteúdo contido na página número 9
I 155"(6)/,") POWER PLANER @- Model 18058 I I Note: The switch, noise suppressor, plug and other part configurations may differ from country to country. 9
Resumo do conteúdo contido na página número 10
':tM GtD DESCRIPTION 'LtM DESCRIPTION MACHINE MACHINE 42 1 Drum Housing 1 1 CORD ASSEMBLY IAmmblsd Cord. Plup E Cord Guard1 43 4 P. H. Screw M4x14 (With Washer1 2 2 P. H. Scnw M4xJ) (With Washer1 U 1 V.PuIIey 6-30 P. H. Screw M4xl8 IWah Washerl 3 2 Rubber Pin 6 45 1 4 1 Strain Reld 46 4 P. H. Screw M4r5 (With Washed 5 1 Cord Guard 41 e H. F. H. 8011 M6x17 6 1 Handle Sat 48 2 Drum Plate P. H. Scnw M5x12 IWiIh Wiherl 7 4 Adlusting Plats 49 2 8 2 Brush Holder Cap 50 1 Front
Resumo do conteúdo contido na página número 11
P MAKI’LA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from worlananship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or m
