Resumo do conteúdo contido na página número 1
22" PLANER
Model 201
Instruction Manual & Parts List
M-0460224
(800) 274-6848
www.powermatic.com
Resumo do conteúdo contido na página número 2
This manual has been prepared for the owner and operators of a Powermatic Model 201 Planer. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your planer, and to aid in using the machine safely, read this manual thoroughly and follow all instructions carefully
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS Safety Rules....................................................................................................................................................4-5 Safety: Decals ....................................................................................................................................................6 Specifications .............................................................................................................................
Resumo do conteúdo contido na página número 4
SAFETY RULES As with all machines, there is a certain amount of hazard involved with the use of this planer. Use the machine with the respect and caution demanded where safety precautions are concerned. When normal safety precautions are overlooked or ignored, personal injury to the operator can result. Read, understand and follow the safety and operating instructions found in this manual. Know the limitations and hazards associated with this planer. Electrical grounding.
Resumo do conteúdo contido na página número 5
If stock stops feeding: If the board being planed stops feeding, disengage or turn the feed off and turn the power off. Wait until the cutterhead comes to a complete stop before lowering the table to remove the board. NEVER lower the table with the power on and the stock still in the machine, as a kickback can occur. Hand safety. Keep hands outside the machine. NEVER reach under the guards to try to clear stock that stops feeding. Do not clear chips and sawdust with hands; use a bru
Resumo do conteúdo contido na página número 6
Familiarize yourself with the following safety notices used in this manual: CAUTION: (This means that if precautions are not heeded, it may result in minor or moderate injury and/or possible machine damage) WARNING: (This means that if precautions are not heeded, it could result in serious injury or possibly even death). SAFETY Familiarize yourself with the location and content of this decal on your machine. !
Resumo do conteúdo contido na página número 7
SPECIFICATIONS: Model 201, 22” Planer Table with standard extensions........................................................................................................................ 28” x 38” Maximum cutting width............................................................................................................................................. 22" Maximum thickness..............................................................................................................
Resumo do conteúdo contido na página número 8
RECEIVING Open shipping crate and check for shipping damage. Report any damage immediately to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Contents of crate: 1 planer 1 dust chute w/ hardware 4 special hex head screws w/ hex nuts 4 foot pads w/ hardware 1 knife-setting gauge 1 6mm hex wrench 1 8mm hex wrench 1 10mm hex wrench 1 12mm & 14mm wrench 1 22mm & 24mm wrench INSTALLATION Remove t
Resumo do conteúdo contido na página número 9
INSPECTION Before putting power to the machine, check that all screws are tight, that all mechanical functions work freely and that the cutterhead turns freely without knife contact with the chipbreaker or pressure bar. ADJUSTMENTS Tools required Philips screwdriver Hex wrenches (provided) Open-end wrench (provided) DEPTH OF CUT Depth of cut is controlled by raising or lowering the table. This is done by using the handwheel (A), shown in Figure 3. 1. Loose
Resumo do conteúdo contido na página número 10
OPENING HOOD To open the hood for access to the cutterhead, remove the two hex screws with the 22mm wrench provided. See Figure 6. KNIFE INSTALLATION & ADJUSTMENT CAUTION: Use care when placing hands near knives as they are extremely sharp and can cause severe cuts. Installing knives on a planer is an exacting process. If the knives are not to be jointed and ground, end-to-end and knife-to-knife relationship must be held within .001" (.03mm) for accurate and s
Resumo do conteúdo contido na página número 11
WARNING: After installing knives, re-check all gib screws. Loose gib screws can result in knives being thrown out of the cutterhead, causing severe damage to the machine and possible serious or fatal injury to the operator or bystanders. THE FEED SYSTEM OF YOUR PLANER (Figure 9) 1. Anti-kickback fingers 2. Infeed roll 3. Chipbreaker 4. Cutterhead 5. Pressure bar 6. Outfeed roll ANTI-KICKBACK FINGERS Anti-kickback fingers help prevent stock fr
Resumo do conteúdo contido na página número 12
To adjust the infeed roll: 1. Place a bed and feed roll gauge (accessory #2230002) under a knife in the cutterhead and raise the table until the gauge contacts the knife at the apex of its curve. See Figure 10. NOTE: If a bed and feed roll gauge is not available, use a finished block of wood with notches cut out for the table rolls, and a feeler gauge. See Figure 11 for an example of a wood block used for a gauge. 2. Move the gauge to the extreme left side of the infeed roll
Resumo do conteúdo contido na página número 13
If it is too high, a shallow "clip" will occur at each end of the board. If it is too low, stock will not feed through. Use a bed and feed roll gauge to set the full length of the pressure bar to be .000-.001" (.02mm) above the arc of the cutterhead. Figure 13 shows the height adjustment screw (C) and the spring tension adjustment screw (D) for the pressure bar. This initial setup is a starting point and final adjustment may have to be made during a test cut. OUTFEED ROLL T
Resumo do conteúdo contido na página número 14
4. Repeat the process for the left side, and then re- check the right side. It is important that both ends of the table rolls be the same height to help prevent skewing of the board as it feeds through the machine. 5. Re-tighten the hex nuts (C-Fig. 15) on both ends of the table roll. Repeat for other roll. TABLE ADJUSTMENTS The planer table is raised and lowered by twin screws supported on bearings, and is guided by machined surfaces on the side panels. The fit-up to prevent
Resumo do conteúdo contido na página número 15
Learning to read a board for imperfections will save hours in adjusting a planer to operate properly. Following are some problems that may arise and their probable solutions: FEED RESTRICTION: This is caused either by the table rolls being set too low for roughing operations or from a low pressure bar. About 90 percent of the time, the pressure bar is too low. As the sharp edge of the planer knives wear, you must compensate for this wear by raising the pressure bar an equal amo
Resumo do conteúdo contido na página número 16
CHATTER: Chatter marks usually appear on thin material. See Figure 21. Even at their lowest point, the table rolls are too high to handle thin material. Solve the problem by either using a slave board or making an auxiliary table out of Formica countertop material, cleating at each end of the table to keep it stationary. TAPERS: If the machine planes a taper across the full width of the board, as shown in Figure 22, the table is not parallel with the cutterhead. First check tha
Resumo do conteúdo contido na página número 17
MAINTENANCE Periodic or regular inspections are required to ensure that the machine is in proper adjustment, that all screws are tight, that belts are in good condition, that dust has not accumulated in the electrical enclosures, and that there are no loose or worn electrical connections. Buildup of sawdust and other debris can cause your machine to plane inaccurately. Periodic cleaning is not only recommended but mandatory for accurate planing. Close-fitting parts, such as the
Resumo do conteúdo contido na página número 18
TROUBLE-SHOOTING: OPERATING PROBLEMS (201 Planer) PROBLEM POSSIBLE CAUSE SOLUTION Snipe 1. Table rollers not set properly. 1. Adjust rollers to proper height. 2. Inadequate support of long boards. 2. Support long boards with extension (NOTE: Snipe can be rollers. minimized but not 3. Uneven feed roll pressure front to back. 3. Adjust feed roll tension. eliminated.) 4 Dull knives 4. Sharpen knives. 5. Lumber not butted properly. 5. Butt end to end each piec
Resumo do conteúdo contido na página número 19
TROUBLE-SHOOTING: MECHANICAL & ELECTRICAL PROBLEMS (201 Planer) PROBLEM POSSIBLE CAUSE SOLUTION Uneven depth 1. Knife projection 1. Adjust knife projection. of cut side to side 2. Cutterhead not level with bed. 2. Level bed. Board thickness 1. Depth of cut scale incorrect. 1. Adjust depth of cut scale. does not match depth of cut scale Chain jumping 1. Inadequate tension. 1. Adjust chain tension. 2. Sprockets misaligned. 2. Align sprockets. 3. Sprockets worn.
Resumo do conteúdo contido na página número 20
Machine will not start/ 7. Motor starter failure. 7. (continued) restart or repeatedly If voltage between starter and motor is incorrect, trips circuit breaker you have a starter problem. or blows fuses If voltage between starter and motor is correct, you have a motor problem. 8. Motor failure. 8. If electric motor is suspect, you have two options: Have a qualified electrician test the motor for function or remove the motor and take it to a quality electr
