Resumo do conteúdo contido na página número 1
MultiSync Hivid 3500 Projector
Large Screen MultiSync Projection System
User’s Manual
Model number: XL-3500
Resumo do conteúdo contido na página número 2
Precautions CAUTION: To turn off main power, be sure to remove the Please read this manual carefully before using your NEC plug from power outlet. The power outlet socket should be MultiSync Hivid 3500 Projector and keep the manual handy installed as near to the equipment as possible, and should for future reference. be easily accessible. 3. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. WARNING AVERTISSEMENT TO PREVEN
Resumo do conteúdo contido na página número 3
INTRODUCTION Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings. Installation 1. Place the projector on a flat, level surface and in a dry area free from dust and moisture. 2. Do not place the projector in direct sunlight, near heaters or heat radiating appliances. 3. Exposure to direct sunlight, smoke or steam could harm internal components. 4. Handle your projector carefull
Resumo do conteúdo contido na página número 4
INTRODUCTION Recommandations importantes Ces instructions de sécurité ont pour but d'assurer une longue vie à votre projecteur et d'éviter un incendie ou une décharge électrique. Prière de les lire avec attention et de tenir compte de tous les avertissements. Installation 1. Placer le projecteur sur une surface plate et de niveau, et dans un endroit sec et à l'abri des poussières et de l'humidité. 2. Ne pas exposer le projecteur aux rayons directs du soleil, ni le placer près d'un chauffage ou d
Resumo do conteúdo contido na página número 5
VISUAL SYSTEMS DIVISION 123456 12345 6 12345 6 12345 6 12345 6 123456 LIMITED WARRANTY . NEC Technologies, Inc.(hereafter NECTECH)warrants this prod- 1. To obtain service on your product, consult the dealer from uct to be free from defects in material and workmanship under the whom you purchased the product, or ship it prepaid to any following terms. authorized NECTECH service center. 2. Whenever warranty service is required, the original dated in HOW LONG IS THE WARRANTY voice (or a copy) must
Resumo do conteúdo contido na página número 6
123456 1 2345 6 1 2345 6 1 2345 6 1 2345 6 1 2345 6 123456 TABLE OF CONTENTS. INTRODUCTION Introduction To The MultiSync Hivid 3500 Projector.............. 7 How Do You Get Started?....................................................... 7 What’s In The Box? ................................................................ 7 1.PART NAMES AND FUNCTIONS Input Panel Features ............................................................... 8 Ajusting and Setting (Adjust Menu)...........................
Resumo do conteúdo contido na página número 7
123456 12345 6 12345 6 12345 6 12345 6 12345 6 123456 INTRODUCTION. This section introduces you to your new MultiSync Hivid 3500 Projector, provides a list of materials that comes with your projector and describes the features and controls. Congratulations On Your Purchase Of The MultiSync Hivid 3500 Projector TM The MultiSync Hivid 3500 is one of the very best projectors available today. Digital Light Processing TM (DLP ) by Texas Instruments enables you to project high bright precise images up
Resumo do conteúdo contido na página número 8
12345 6 12345 6 12345 6 12345 6 12345 6 123456 1.PART NAMES AND FUNCTIONS. This compartment accommodates the remote control. The remote control serves as the key panel on the projector when it is plugged and fit in this compartment. POWER ON/STANDBY Indicator lights in green when the projector is turned on and lights in red when the projector is in standby. 11111 @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@
Resumo do conteúdo contido na página número 9
1.PART NAMES AND FUNCTIONS 6666677777 88 888 55 555 99 POWER STANDBY RCREADY LAMP 999 POWER ON/OFF
OFF ON 00000 INDICATOR AA IN REMOTE2 OUT AAA CC CCC BB BBB REMOTE1 IN OPTION OUT DD DDD EEEEE @@ @@ @@ @@ @@ @@ @@ @@ @@@@ @@ @@ @@@@@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@@@ @@@@ @@ @@ @@@@ @@ @@ @@
Resumo do conteúdo contido na página número 10
1.PART NAMES AND FUNCTIONS OPTIONAL Boards VIDEO INPUT Board [XG VIDIN(A)] Front view LR LR VIDEO S-VIDEO VIDEO INPUT VIDEO S-VIDEO AUDIO INPUT 12 3 4 5 1 Active Indicator (green LED) ...... Lights up when this board is selected. 2 VIDEO INPUT Terminal ............... Connects composite video output signals. 3 S-VIDEO INPUT Terminal ........... Connects S-video output signals. 4 VIDEO INPUT Terminal ............... Connect to the audio outputs of the external equipment such as a VCR. (Not avai
Resumo do conteúdo contido na página número 11
9 8 7 6 RGB 1.PART NAMES AND FUNCTIONS The combination of the rotary switch and the jumper pins allows the projector to accept VIDEO signals. Note that this board cannot accept RGB signals when board is set to VIDEO input. Rotary switch (S1001) Jumper (S1002, S1003, S1004) Setting of Rotary switch No. Mark Input 0 VIDEO VIDEO input 5 1 OPTION Option *1 *2 3 RGB RGB input 2, 4-9 Not used *1 ) No 1 is for future system expansion. *2) No 3 is factory preset. Table for Setting Rotary S
Resumo do conteúdo contido na página número 12
1.PART NAMES AND FUNCTIONS Remote control unit 1 Remote Jack 1 Insert the supplied remote cable here. 2 POWER Buttons (ON/OFF) Press the ON button to turn the projector on when the projector is in the standby condition (STANDBY and RC POWER INPUT READY indicators lit). Press the OFF button to return the ON OFF 1 ABC 2 DEF 3 GHI projector to the standby condition. 2 TEST 4 JKL 5 MNO 6 PQR 3 TEST Button 3 H Press to display the TEST PATTERN menu from which 4 OPERATE ADJUST 7 STU 8 VWX 9 YZ/ you ca
Resumo do conteúdo contido na página número 13
1.PART NAMES AND FUNCTIONS B HELP Button N POSITION Button Press to display the explanation of the current selected Press to enter the position mode. You can adjust the function and available functions. O R, G, and B Buttons C SIG LEVEL Button The R and B buttons are used for Uniformity only. Press to display the SIGNAL LEVEL menu. You can set the level for an RGB or YUV signal. P CURSOR Buttons Used for increasing and decreasing control levels, cursor D GAMMA Button movement and convergence adj
Resumo do conteúdo contido na página número 14
1.PART NAMES AND FUNCTIONS Remote Control Battery Installation 1. Press firmly and slide the battery cover off. 2. Remove both old batteries and install new ones (AA). Ensure that you have the batteries’ polarity (+/-) aligned correctly. 3. Slip the cover back over the batteries until it snaps into place. NOTE: The remote control is powered by two alkaline 1.5V AA batteries. Remote Control Precautions • When using the remote wirelessly, you should be within 23 ft.(7 m) of the projector and at a
Resumo do conteúdo contido na página número 15
OPEN Remote Control Unit 1.PART NAMES AND FUNCTIONS When using the remote control as the key panel on the projector: The following steps are necessary only when the projector is installed on the ceiling. When you use the projector in floor projection, you do not need to fasten the remote with the metal fitting. Simply open the lid and put the remote in the compartment. @@ @@ @@ @@@@ @@@@ @@@@@@ @@ @@@@@@ @@
Resumo do conteúdo contido na página número 16
123456 12345 6 12345 6 12345 6 12345 6 12345 6 123456 2. INSTALLATION This section describes how to set up your MultiSync Hivid 3500 projector and how to connect video and audio sources. Setting Up Your MultiSync Hivid 3500 Projector Pulling Out the Handles To set up and use your MultiSync Hivid 3500 Projector, you Pull out the handle from the bottom side. must first do: Retracting the Handles 1. Determine the screen size and the optional lens to be used. Press down the two levers at the same ti
Resumo do conteúdo contido na página número 17
2.INSTALLATION 5. To move the projected image up or down, rotate the Lens vertical adjustment lens vertical knob in the top compartment right above the lens barrel. 6. Adjust the focus using the Focus knob at the lens. 7. Increase or reduce the size of the projected image by using the ZOOM/PAN button on the remote control. @@ @@@@ @@ @@ @@ @@ @@@@ @@@@ @@ @@ @@ @@ @@ @@ @@ @@
Resumo do conteúdo contido na página número 18
2.INSTALLATION Ceiling Installation the projector’ s performance will be affected and its reliabil- Installing your MultiSync Hivid 3500 Projector on the ceiling ity will decrease. Be sure to position the projector properly. must be done by a qualified technician. Contact your NEC dealer for more information. The manufacturer will not be held responsible for any Do not attempt to install the projector yourself. problems occurring when the projector is not installed in the proper position. The fo
Resumo do conteúdo contido na página número 19
2.INSTALLATION Reflecting The Image Using a mirror to reflect your projector’s image enables you to enjoy a much larger image. Contact your NEC dealer if you need a mirror. If you’re using a mirror and your image is inverted, use the ADJUST-SETTING Menu to access to correct the orientation. (See page 59.) Rear Screen Projection You can use your MultiSync Hivid 3500 to project an image from the rear onto a transparent screen. The distance the projector must be from the screen is the same as if yo
Resumo do conteúdo contido na página número 20
2.INSTALLATION EXAMPLES OF CONNECTIONS. CAUTIONS ON CONNECTIONS: • Unplug the projector and other equipment from the AC • Confirm your connection layout with the user’s manual supply before making connections. accompanying the equipment to be connected with the ISS- • Make sure that the plug of the power cord is properly 6020/ISS-6020G Switcher. connected to the power outlet. A loose connection may cause hum or noise. When Used in Stand Alone Operation Components with RGB and H/V SYNC outputs su
