Resumo do conteúdo contido na página número 1
MultiSync XT5000
High Light Output Projection System
User’s Manual
Resumo do conteúdo contido na página número 2
Precautions CAUTION: To turn off main power, be sure to remove the Please read this manual carefully before using your NEC plug from power outlet. The power outlet socket should be MultiSync XT5000 Projector and keep the manual handy for installed as near to the equipment as possible, and should future reference. be easily accessible. WARNING 3. GSGV Acoustic Noise Information Ordinance: This is a Class A product. In a domestic environment this product may The sound pressure level is less than 7
Resumo do conteúdo contido na página número 3
Fire and Shock Precautions Important Safeguards 1. Ensure that there is sufficient ventilation and that vents are These safety instructions are to ensure the long life of your unobstructed to prevent potentially dangerous concentra- projector and to prevent fire and shock. Please read them tions of ozone and the build-up of heat inside your projector. carefully and heed all warnings. Allow at least 8 inches (20cm) of space between your projector and a wall. Allow at least 20 inches (50 cm) of sp
Resumo do conteúdo contido na página número 4
Précautions contre l'incendie ou la décharge Recommandations importantes 1. S'assurer qu'il y ait une ventilation suffisante et que les Ces instructions de sécurité ont pour but d'assurer une longue ouvertures ne soient pas obstruées afin d'éviter des vie à votre projecteur et d'éviter un incendie ou une décharge concentrations potentiellement dangereuses d'ozone et électrique. Prière de les lire avec attention et de tenir compte l'accumulation de chaleur à l'intérieur du projecteur. de tous les
Resumo do conteúdo contido na página número 5
LIMITED WARRANTY (USA and Canada only) NEC Technologies, Inc.(hereafter NECTECH)warrants this prod- HOW YOU CAN GET WARRANTY SERVICE uct to be free from defects in material and workmanship under 1. To obtain service on your product, consult the dealer from the following terms. whom you purchased the product, or ship it prepaid to any authorized NECTECH service center. HOW LONG IS THE WARRANTY 2. Whenever warranty service is required, the original dated in Parts and labor are warranted for (1) On
Resumo do conteúdo contido na página número 6
TABLE OF CONTENTS INTRODUCTION Lamp.................................................................................... E–35 Introduction to the MultiSync XT5000 Projector ................... E–7 Lamp Mode ................................................................... E–35 Getting Started ...................................................................... E–7 Lamp Output ................................................................. E–35 What's in the Box? ............................
Resumo do conteúdo contido na página número 7
INTRODUCTION This section introduces you to your new MultiSync XT5000 Projec- Getting Started tor, provides a list of materials that comes with your projector and The fastest way to get started is to take your time and do everything describes the features and controls. right the first time. Taking a few minutes now to review the manual may save you hours later on. At the beginning of each section of the Congratulations On Your Purchase Of The manual you'll find an overview. If the section doesn'
Resumo do conteúdo contido na página número 8
1. Part Names and Functions Stacking Pad (4 pcs) Digital Input Terminal Panel Remote Sensor PC Card Slot Insert a flash memory card here to upgrade the projector system software or copy data Lens (Optional) Carrying Handle Input Terminal Panel Ventilation (out) Ventilation (in) Release Lever (both sides) * To turn on the main power to the projector, press the switch to the Foot ON position (I) and the POWER indicator on the rear panel will turn amber in color. Press to the OFF position (0) to tu
Resumo do conteúdo contido na página número 9
Controls 11 10 9 8 7 5 4 2 Remote sensor LENS SHIFT FOCUS ZOOM MENU SELECT ENTER INDICATOR POWER ON ON/OFF - + OFF STATUS CANCEL 6 3 1 1. Power Button 5 Enter Button Press to turn the projector on when the projector is in the standby Executes your menu selection and activates items selected from condition (Main Power switch must be on and the POWER indica- the menu. When the slidebar or dialog box is diplayed: tor lit amber). Press and hold for 2 seconds to turn off the projec- Pressing this but
Resumo do conteúdo contido na página número 10
1 INPUT 3 RGB Connector (Mini D-Sub 15 pin) Terminal Panel Connect your PC or other analog RGB equipment such as a high- definition document camera. 56 2 Option Connector (Mini D-Sub 9 pin) For system expansion such as PC-control. IN: connect to the external equipment such as PC. INPUT3 INPUT2 INPUT1 INPUT4 OUT: for daisy-chaining multiple projectors and operating them RGB R/Cr R/Cr Cr with the same external equipment. To do so, connect to a 1 second projector' s IN terminal to relay the input a
Resumo do conteúdo contido na página número 11
10 INPUT 8 S-VIDEO 2Terminal (Mini DIN 4 pin) Connect to the S-video output of the external equipment such as a VCR with an S-video output. This terminal allows switching be- tween S2 and S1 VIDEO input modes. See the "S-Video Mode Select" section for more information. Push the left side of the panel to open the compartment for the RGB Digital connectors and the optional SDI board. OUTPUT INPUT9 OUTPUT INPUT 0 RGB DIGITAL SDI 11 Space to install the optional SDI board. 11 RGB Digital Input/Outpu
Resumo do conteúdo contido na página número 12
3 MENU Remote Control Press to display the main menu. While pressing and holding CTL, press this button to display the Remote Control ID dialog box to specify the remote control ID. 4 ENTER POWER OFF ON Executes the menu selection and activates items selected from the 1 2 menu. When the slidebar or dialog box is diplayed: Pressing this button confirms adjustments/setting and returns to MENU the previous menu display. 5 3 ADDRESS BS - + ENTER 5 CURSOR (Up/Down/Left/Right) When pressed together, t
Resumo do conteúdo contido na página número 13
12 INFO 26 CTL Displays the "Source Information" or "Projector Information" win- Used in conjunction with other buttons, similar to a shift key on a dow. This button toggles between these two windows. computer. 27 Infrared Transmitter 13 TEST Direct the remote control toward the remote sensor on the projec- Press to display the test pattern. Pressing this button sequentially tor cabinet. selects nine test patterns. 14 HELP 28 Remote Jack Provides online help. Connect your remote control cable he
Resumo do conteúdo contido na página número 14
2. INSTALLATION This section describes how to install the lens, set up the projector and 3) Lift up the lower lens hood by 1 cm to release the hook. Re- how to connect video and audio sources. move the lower lens hood. Optional Lens Installation Four optional lenses are available: TL-08SF, TL-1Z, TL-2Z and TL- 4Z. Preparation * Turn the projector off, wait for the cooling fan to stop, then turn off the main power switch on the rear panel. Check that the projector has cooled off sufficiently befo
Resumo do conteúdo contido na página número 15
3) Rotate the lens barrel clockwise to fix the lens unit. 2) Insert the upper lens hood while pushing the left and right bottom. Secure the two screws. Lens barrel 3. Secure the fixed screws and connect the extension cable attached to the projector. NOTE: This completes installation for the optional lens TL-08SF 1) Secure the three screws on the lens holder. 2) Insert the connector of the lens unit into the socket of the ex- and TL-1Z. For TL-2Z and TL-4Z, attach the supplied dust cap as tension
Resumo do conteúdo contido na página número 16
Selecting A Location The further your projector is from the screen or Setting Up The projector wall, the larger the image. The minimum size the image can be pro- To set up and use the projector, you must first do: jected is 80" (2 m) measured diagonally. The largest the image can be 1. Determine the screen size and the optional lens to be used. is 500" (12.7 m). NOTE: Refer to page E-14 for lens installation. 500" 400" 2. Set up a screen or select a non-glossy white wall onto which you 300" can
Resumo do conteúdo contido na página número 17
OFF POWER ON Attaching the Power Cable Stopper The Power cable stopper is provided with the projector so that the cable cannot be accidentally unplugged from the AC IN. 1) Remove two screws. These screws are used later again. 2) Plug the power cable into the AC IN and then attach the stopper. Power cable Stopper 3) Fix the stopper using the two screws. E – 17
Resumo do conteúdo contido na página número 18
Screen Size (Diagonal) / Projection Distance Screen Size and Projection Distance Lens Shift Adjustable Range 1. Place your projector on a flat level surface at the optimal distance Lens can be shifted within the shaded area as shown below using the from the screen. (Avoid having bright room lighting or sun light normal projection position as a starting point. directly on the screen or projection surface.) (H: width of projected image, V: height of projected image) 2. Connect the power cable, rem
Resumo do conteúdo contido na página número 19
Reflecting The Image Top View Using a mirror to reflect your projector's image enables you to enjoy Normal projection a much larger image in a much smaller space. Contact your dealer if you need a mirror. If you're using a mirror and your image is inverted, use the [Main Menu] → [Projector Options] → [Setup] → [Orientation] to select the correct orientation. (See page E-39.) Rear Screen Projection You can use your XT5000 to project an image from the rear onto a Lens shifted transparent screen. T
Resumo do conteúdo contido na página número 20
OUTPUT INPUT9 OUTPUT INPUT9 Setting up for Double or Triple Stacking in Link Mode INPUT3 INPUT2 INPUT1 INPUT4 RGB R/Cr R/Cr Cr G/Y G/Y Y OPTION IN B/Cb B/Cb Cb OUT H/HV H/HV Master projector REMOTE1 V V INPUT3 INPUT2 INPUT1 INPUT4 RGB R/Cr R/Cr Cr Slave projector G/Y G/Y Y OPTION IN B/Cb B/Cb Cb OUT H/HV H/HV REMOTE1 V V OUTPUT INPUT9 OUTPUT INPUT 0 INPUT3 INPUT2 INPUT1 INPUT4 RGB RGB R/Cr R/Cr Cr DIGITAL SDI G/Y G/Y Y DFP cable (supplied) OPTION IN OUTPUT INPUT9 OUTPUT INPUT 0 B/Cb B/Cb Cb RGB
