Resumo do conteúdo contido na página número 1
TS4G-32GSDHC6-P2
TS4G-32GSDHC6-P2
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2
Description Features
Transcend High Capacity SD Card series are • RoHS compliant product.
specifically designed to meet the High Capacity, High • Card Lid material: PC (comply with UL94,Flame Class:HB)
Definition Audio and Video requirement for the latest • Operating Voltage: 2.7 ~ 3.6V
Digital Cameras, DV Recorders, Mobile Phones, etc,. • Operating Temperature: -25 ~ 85°C
The new de
Resumo do conteúdo contido na página número 2
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Architecture 2 Transcend Information Inc.
Resumo do conteúdo contido na página número 3
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Bus Operating Conditions • General Parameter Symbol Min. Max. Unit Remark Peak voltage on all lines -0.3 V +0.3 V DD All Inputs Input Leakage Current -10 10 µA All Outputs Output Leakage Current -10 10 µA • Power Supply Voltage Parameter Symbol Min. Max. Unit Remark Supply voltage V 2.7 3.6 V DD Output High Voltage V 0.75* V V I =-100uA@V Min. OH DD OH DD Output Low V
Resumo do conteúdo contido na página número 4
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Single card capacitance C 10 pF CARD ≤ Maximum signal line inductance 16 nH f 20 MHz PP Pull-up resistance inside card (pin1) R 10 90 kΩ May be used for card DAT3 detection Note that the total capacitance of CMD and DAT lines will be consist of C , C and one C only because they are HOST BUS CARD connected separately to the SD Memory Card host. Host should consider total bus cap
Resumo do conteúdo contido na página número 5
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • Bus Signal Levels As the bus can be supplied with a variable supply voltage, all signal levels are related to the supply voltage. To meet the requirements of the JEDEC specification JESD8-1A and JESD8-7, the card input and output voltages shall be within the following specified ranges for any V of the allowed voltage range: DD Parameter Symbol Min. Max. Unit Remark Output HIGH
Resumo do conteúdo contido na página número 6
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • Bus Timing Parameter Symbol Min Max. Unit Remark Clock CLK (All values are referred to min (V ) and max (V ) IH IL Clock frequency Data Transfer Mode f 0 25 MHz C ≤ 10 pF, (1 card) PP CARD Clock frequency Identification Mode f 0 /100 400 KHz C ≤ 10 pF, (1 card) OD (1) CARD Clock low time t 10 ns C ≤ 10 pF, (1 card) WL CARD Clock high time t 10 ns C ≤ 10 pF, (1 card) WH CARD
Resumo do conteúdo contido na página número 7
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Output Delay time during Data Transfer Mode t 0 14 ns C ≤ 40 pF, (1 card) ODLY L Output Delay time during Identification Mode t 0 50 ns C ≤ 40 pF, (1 card) ODLY L (1) 0 Hz means to stop the clock. The given minimum frequency range is for cases were continues clock is required 7 Transcend Information Inc.
Resumo do conteúdo contido na página número 8
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • Bus Timing (High Speed Mode) Parameter Symbol Min Max. Unit Remark Clock CLK (All values are referred to min (V ) and max (V ) IH IL Clock frequency Data Transfer Mode f 0 50 MHz C ≤ 10 pF, (1 card) PP CARD Clock low time t 7 ns C ≤ 10 pF, (1 card) WL CARD Clock high time t 7 ns C ≤ 10 pF, (1 card) WH CARD ≤ Clock rise time t 3 ns C 10 pF, (1 card) TLH CARD Clock fall ti
Resumo do conteúdo contido na página número 9
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Output Delay time during Data Transfer Mode t 14 ns C ≤ 40 pF, (1 card) ODLY L Output Hold time t 2.5 ns C ≤ 40 pF, (1 card) OH L 1 Total System capacitance for each line C 40 pF (1 card) L 1) In order to satisfy severe timing, host shall drive only one card. 9 Transcend Information Inc.
Resumo do conteúdo contido na página número 10
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Reliability and Durability Temperature Operation: -25°C / 85°C Storage: -40°C (168h) / 85°C (500h) Junction temperature: max. 95°C Moisture and corrosion Operation: 25°C / 95% rel. humidity Storage: 40°C / 93% rel. hum./500h Salt Water Spray: 3% NaCl/35C; 24h acc. MIL STD Method 1009 Durability 10.000 mating cycles; test procedure: tbd. Bending 10N Torque 0.15N.m or +/-2.5 deg Dr
Resumo do conteúdo contido na página número 11
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Register Information Within the card interface six registers are defined: OCR, CID, CSD, RCA, DSR and SCR. These can be accessed only by corresponding commands (see Chapter 4.7). The OCR, CID, CSD and SCR registers carry the card/content specific information, while the RCA and DSR registers are configuration registers storing actual configuration parameters. 1. OCR register The 32
Resumo do conteúdo contido na página número 12
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 OCR Register Definition 1) This bit is valid only when the card power up status bit is set. 2) This bit is set to LOW if the card has not finished the power up routine. The supported voltage range is coded as shown in Table 5-1. A voltage range is not supported if the corresponding bit value is set to LOW. As long as the card is busy, the corresponding bit (31) is set to LOW. 2. CID
Resumo do conteúdo contido na página número 13
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • PRV The product revision is composed of two Binary Coded Decimal (BCD) digits, four bits each, representing an “n.m” revision number. The “n” is the most significant nibble and “m” is the least significant nibble. As an example, the PRV binary value field for product revision “6.2” will be: 0110 0010 • PSN The Serial Number is 32 bits of binary number. • MDT The manufactur
Resumo do conteúdo contido na página número 14
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 The CSD Register Fields (CSD Version 2.0) The following sections describe the CSD fields and the relevant data types. If not explicitly defined otherwise, all bit strings are interpreted as binary coded numbers starting with the left bit first. • CSD_STRUCTURE Field structures of the CSD register are different depend on the Physical Specification Version and Card Capacity. The C
Resumo do conteúdo contido na página número 15
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 CSD Register Structure • TAAC This field is fixed to 0Eh, which indicates 1 ms. The host should not use TAAC, NSAC, and R2W_FACTOR to calculate timeout and should uses fixed timeout values for read and write operations (See 4.6.2). • NSAC This field is fixed to 00h. NSAC should not be used to calculate time-out values. • TRAN_SPEED The following table defines the maxi
Resumo do conteúdo contido na página número 16
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Note that for current SD Memory Cards that field must be always 0_0110_010b (032h) which is equal to 25MHz - the mandatory maximum operating frequency of SD Memory Card. In High-Speed mode, that field must be always 0_1011_010b (05Ah) which is equal to 50MHz. And when the timing mode returns to the default by CMD6 or CMD0 command, its value will be 032h. • CCC The SD Memory Card
Resumo do conteúdo contido na página número 17
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • C_SIZE This field is expanded to 22 bits and can indicate up to 2 TBytes (It is the same as the maximum memory space specified by a 32-bit block address.) This parameter is used to calculate the user data area capacity in the SD memory card (not include the protected area). The user data area capacity is calculated from C_SIZE as follows: memory capacity = (C_SIZE+1) * 512K byte As
Resumo do conteúdo contido na página número 18
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 This field is set to 0. Host should not use this field. • COPY Defines if the contents is original (= ‘0’) or has been copied (=’1’). The COPY bit for OTP and MTPdevices, sold to end consumers, is set to ‘1’ which identifies the card contents as a copy. The COPY bit is an one time programmable bit. • PERM_WRITE_PROTECT Permanently protects the whole card content against overwriti
Resumo do conteúdo contido na página número 19
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 4. RCA Register The writable 16-bit relative card address register carries the card address that is published by the card during the card identification. This address is used for the addressed host-card communication after the card identification procedure. The default value of the RCA register is 0x0000. The value0x0000 is reserved to set all cards into the Stand-by State with CMD7
Resumo do conteúdo contido na página número 20
TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 is 0x404. 6. SCR Register In addition to the CSD register there is another configuration register that named - SD CARD Configuration Register (SCR). SCR provides information on SD Memory Card's special features that were configured into the given card. The size of SCR register is 64 bit. This register shall be set in the factory by the SD Memory Card manufacturer. The following table
