Resumo do conteúdo contido na página número 1
™
COMMUNICATIONS
™
Wake & Shake
Large Display Alarm Clock
& Telephone Ring Signaler
User’s Guide
CS-WS1manual.pm 1 2/5/04, 20:07
Resumo do conteúdo contido na página número 2
Important Safety Instructions When using your alarm clock, always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons, or property, including the following: 1.Read and understand all instructions, warnings and product markings. 2.Be aware there is a slight possibility of electrical shock from lightening. 3.Do not use this product near or in water or when you are wet. If the product comes in contact with any liquid, unplug the power cord and telephon
Resumo do conteúdo contido na página número 3
Description %:)$ CS-WS1manual.pm 3 2/5/04, 20:07
Resumo do conteúdo contido na página número 4
Installation Your Wake & Shake offers you the option of using it as both an alarm clock and a telephone ring signaler. The following diagram shows you how to set up your Wake & Shake so you may use it for both. NOTE: Setting up your Wake & Shake as a tele- phone ring signaler requires the use of a dual phone jack adapter. This is a small inexpensive device available at your local drug or hardware store. (See #1) 1.Plug Dual Phone Jack Adapter into wall jack. 2.Plug telephone line from your telep
Resumo do conteúdo contido na página número 5
How To Set The Time 1.Press and hold the Time button. 2.Holding down the Time button, press the hour button, then the minute button until the correct hour appears. 3.Release the Time button. NOTE: There is a PM indicator on the top left of the display. How To Set The Alarm Time 1.Press and hold the Alarm button. 2. Holding down the Alarm button, press the Hour button, then Minute button until the exact time you want appears. 3.Release the Alarm button. How To Set The Alarm Mode Your Wake & Shake
Resumo do conteúdo contido na página número 6
Turning the Clock & Telephone Ring Signaler On Adjust the Alarm Function Switch to the setting you prefer. A+T: Clock alarm & telephone ring Signal on OFF: Both clock alarm and telephone ring Signal off T: Telephone Ring Signaling only When the alarm is set to one of the modes, the alarm indicator will appear on the display. Your Wake & Shake distinguishes between the clock alarm and telephone ring alarm by using different patterns. See the table below: ALARM MODE ACTION ALARM CLOCK INCOMING CAL
Resumo do conteúdo contido na página número 7
Alarm Off Button When your clock alarm is activated, you can press the OFF Button on the front of your clock to turn the alarm off. The alarm will still be set for the same time and will operate at the same time the next day. If your alarm is activated but never switched off, it will automati- cally turn off after 2 hours. Telephone Ring Signaler 1.Make sure your Wake & Shake has been installed using the phone cord and is plugged into your telephone wall jack. 2. Adjust the Ringer On/Off switch
Resumo do conteúdo contido na página número 8
Volume and Tone Control Your Wake & Shake allows you to adjust both the volume and tone of the alarm. The Volume Control increases or decreases the loud- ness of the alarm. The Tone Control shapes the sound by making it a higher pitch or a lower pitch. To adjust the Volume & Tone, simply turn the dials located on the front of your clock. You can adjust the strength of the bed shaker by setting the Shaker Switch to Lo (-) or Hi (+). Battery Back-up It is not required to install a battery for your
Resumo do conteúdo contido na página número 9
Limited Warranty ClearSounds Communications warrants the WS1 Wake & Shake Clock against any defect in materials or workmanship for the period of one year from the date of purchase. Within a period of one year from purchase date, ClearSounds Communications will repair or replace (our discretion) your WS1 Wake & Shake Clock at no cost. If we elect to replace your clock, we may replace it with a new or reconditioned product of the same or similar design. Repair or replacement will be warranted for
Resumo do conteúdo contido na página número 10
Regulatory Compliance Part 68 of FCC Rules Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equip- ment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. A plug and jack used to connect this WS1 to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and req
Resumo do conteúdo contido na página número 11
the equipment. If this happens the telephone company will pro- vide advance notice in order for you to make necessary modifi- cations to maintain uninterrupted service. If trouble is experienced with this telephone equipment, for repair or warranty information, please contact ClearSounds Communication at 1-800-965-9043. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equip- ment until the problem is resolved. DO NOT DISASSEMBLE
Resumo do conteúdo contido na página número 12
8160 Madison Ave., Burr Ridge, IL 60527 800.956.9043 V — 800.536.8890 TTY 630.654.9219 FAX • www.clearsoundscom.com CS-WS1manual.pm 12 2/5/04, 20:07
