Resumo do conteúdo contido na página número 1
UV8035
Owner's Manual
Multimedia Receiver
UV8035
Resumo do conteúdo contido na página número 2
UV8035 PREPARATION Getting Started Installation Requirements Speaker Requirements It’s a good idea to read all of the instructions This unit is designed for installation in cars, Only connect speakers rated with a load before beginning the installation. trucks and vans with an existing radio opening. impedance of 4 ohms. Speakers with a load In many cases, a special installation kit will be impedance of less than 4 ohms could damage Contents required to mount the radio to the dashboard. the u
Resumo do conteúdo contido na página número 3
UV8035 INSTALLATION INSTRUCTIONS the dashboard opening, bend as many of Before You Begin DIN Front Mount (Method A) the tabs outward as necessary to firmly 1. Disconnect battery negative terminal. 1. Slide the mounting sleeve off of the chassis secure the sleeve to the dashboard. 2. Remove transport screws. if it has not already been removed. If it is 4. Place the radio in front of the dashboard locked into position, use the removal keys Important Notes opening so the wiring can be brought
Resumo do conteúdo contido na página número 4
UV8035 position it. CAUTION: The rear of the radio 2. Insert the removal keys straight back until must be supported with the strap to prevent they click, and then pull the radio out. If damage to the dashboard from the weight removal keys are inserted at an angle, they of the radio or improper operation due to will not lock properly to release the unit. vibration. Dashboard Dashboard Support Strap Plain Washer Screw (5 x 25mm) Screw Stud Hex Nut (5mm) Spring Washer Removal Key 9. Test radio o
Resumo do conteúdo contido na página número 5
UV8035 maximum screw size. Longer screws may DIN Rear Mount (Method B) Reconnect Battery damage components inside the chassis. This unit has threaded holes in the chassis side When wiring is complete, reconnect the battery panels which may be used with the original negative terminal. factory mounting brackets of some vehicles to mount the radio to the dashboard. Please consult with your local mobile stereo shop for assistance on this type of installation. Screws 1. Remove the existing facto
Resumo do conteúdo contido na página número 6
UV8035 WIRING R (Red) Aux-In (Black) L (White) Video In Subwoofer Out WARNING! Never combine (Yellow) (bridge) outputs for use with 1 (Blue) Video Out 1 speaker. (Yellow) Fuse (15A) Video Out 2 (Yellow) WARNING! Never ground negative speaker leads to Rear Line out chassis ground. R (Red) Parking Gray L (White) Connect to switched side of parking brake circuit. FrontrLineout R (Red) Pink CAUTION: Failure to wire exactly Black L (White) as shown may cause electrical Ground Power Antenna damage
Resumo do conteúdo contido na página número 7
UV8035 DETACHABLE CONTROL PANEL • DO NOT insert the control panel from the Removing the Control Panel Attaching the Control Panel left side. Doing so may damage it. The front panel release button (3) releases the Before re-attaching the front panel, make sure • Do not put pressure on the display or mechanism that holds the front panel to the the electrical terminals on the back of the panel control buttons when handling the front chassis. To detach the front panel, perform the are free of dust
Resumo do conteúdo contido na página número 8
F E U F T O N UV8035 REMOTE CONTROL The remote control will allow you to control the 7. Multi-Zone On/Off • Track Number Entry advanced functions of the UV8035. 8. Tune Up/Fast Forward • File Number Entry 9. Tune Down/Fast Reverse 22. 4 10. Left • Tuner M4 recall, Memory 4 9 11. Right • Track Number Entry 12 12. Up • File Number Entry 1 2 13. Down 23. 5 8 10 14. Seek Up • Tuner M5 recall, Memory 5 4 5 MODE • Radio Tune • Track Number Entry 11 15 VOLUME 16 •Track Up • File Number Entry 6 17 • Fil
Resumo do conteúdo contido na página número 9
UV8035 29. Press repeatedly to select a number in the Operating Range Replacing the Battery tens position for direct track entry (for The head unit remote REMOTE SENSOR When the range of operation of the card remote example, to select track “44”, press the +10 control sensor (22) is control becomes short or stops functioning, button four times and then press the 4 but- located on the right side replace the battery with a new lithium battery. ton). of the control panel. Be sure to observe th
Resumo do conteúdo contido na página número 10
UV8035 OPERATING INSTRUCTIONS Power On/Off display. Press the power/mute button again to restore audio output to the previous level. NOTE: For iPod or Zune video playback, Press and hold the (power/mute) button (1) please refer to owner's manual that came Mode Selector (MODE) or short press any other button on the control with your device. Please complete any panel (except open/eject) to turn the unit on. photo or video setting adjustments before Press this MODE button (9) to select a d
Resumo do conteúdo contido na página número 11
UV8035 Display Selector (D) System Menu (D/MENU) Contrast Turn the rotary encoder to adjust the screen You can change the way playback information Press and hold the D/MENU button (7) for more contrast from “00” to “50”. is displayed to suit your needs. Press the D/ than 3 seconds to display the system menu. Bright DISP button (7) to alternate between the File You can then press the D/MENU button Turn the rotary encoder to adjust the screen Menu and Elapsed Time interface screens, repeatedl
Resumo do conteúdo contido na página número 12
UV8035 Clock speaker “OFF” when using headphones. When • LEVEL Turn the rotary encoder (4) to the right to adjust the rear speaker is “OFF”, the “FADER” audio Turn the rotary encoder clockwise to the minutes or to the left to adjust the hour. function is disabled. increase or counter-clockwise to decrease the Bass level from “-6” to “+6”. “00” Time Form Internal Amplifier (Inter Amp) represents a flat response. Turn the rotary encoder to adjust the clock Turn the rotary encoder to turn the sy
Resumo do conteúdo contido na página número 13
UV8035 • LEVEL in the display. Continue pressing the rotary rotary encode adjust the balance between the Turn the rotary encoder clockwise to encoder to access the following Treble settings: left and right speakers. “C00” represents a increase or counter-clockwise to decrease • LEVEL center balance. the Mid-Range level from “-6” to “+6”. “00” Turn the rotary encoder clockwise to Fader represents a flat response. increase or counter-clockwise to decrease To adjust the fader from “F12” (full
Resumo do conteúdo contido na página número 14
UV8035 encoder to access and modify the following options: • Level: Turn the rotary encoder to adjust the subwoofer Level from “00” to “12”. • LPF: Turn the rotary encoder to adjust the LPF (Low Pass Filter) to 80Hz, 120Hz or 160Hz. Bass Boost (iX-BASS) When listening to music at low volume levels, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. To turn iX-BASS on, press the iX-BASS button (16) on the front panel and then use t
Resumo do conteúdo contido na página número 15
UV8035 TUNER OPERATION AM/FM Band Selector (BAND) Preset Scan NOTE: You can stop the AUTO PRESET Press the B/BAND button (20) to change Press the AS/PS button (15) to scan and play function at any time by pressing the AS/PS between three FM and two AM bands. Each each preset station for 5 seconds each. Press button again. band stores up to six preset stations. AS/PS again to stop preset scan. Manual Tuning Automatic Preset Store Mono/Stereo Reception Press the tune/track |||< button (18) t
Resumo do conteúdo contido na página número 16
UV8035 CD/DVD OPERATION Insert Disc (OPEN) Controlling Playback when the highlighted file is in the column to the far left to display the previous ten files. Press the OPEN button (8) to open the front After inserting an audio disc, the player • Press OK when a file number is highlighted panel and reveal the disc slot. With the label automatically plays the first track. The elapsed or after numeric input to begin playback of surface facing up, gently insert the disc into the playing tim
Resumo do conteúdo contido na página número 17
UV8035 Track Selection • Select “Track” to jump to a specific track function, the elapsed time of each track will be The Track Select functions are used to quickly on a non-DVD disc. shown on the display panel. access the beginning of a track/chapter. Each 3. Use the number keys on the remote control Repeat Play time the track up (|||<) button (18) is pressed, to enter the track number or elapsed time Press the 3/REPEAT button (17) multiple times the next higher track/chapter is selected, as
Resumo do conteúdo contido na página número 18
UV8035 VCD PlayBack Control (PBC) • TITLE: Press to display the title or chapter JPEG CD Operation list. Use the , , or buttons or the If you insert a VCD with playback control After inserting a disc with JPEG files, the unit numeric buttons to enter a title or chapter (version 2.0), playback automatically starts at will search for files with appropriate formats and number, and then press OK to play. the beginning of the first track. then begin to play an image slideshow starting • ANGLE:
Resumo do conteúdo contido na página número 19
UV8035 MEMORY CARD OPERATION This unit can play MP3, WMA, JPEG and MP4 Removing an SD or MMC Card Accessing Card Mode files stored on an SD or MMC Memory card. 1. Detach the front panel. After inserting an SD or MMC card, press the 2. Push in until a “click” is heard. MODE button (9) to select “Card” mode. The Inserting an SD or MMC Card 3. Remove the card. unit will read the files on the Memory Card and 1. Detach the front panel. playback will begin automatically. 2. Insert memory card wit
Resumo do conteúdo contido na página número 20
UV8035 DUAL ZONE OPERATION This unit is equipped with an advanced Dual AV During Dual Zone operation, AV IN 1 and AV IN selected VOL PGM level indicated in the Zone feature, which allows the user to select 2 are considered as the same mode/source. If System Setup menu). different modes of Audio and Video (AV) output AV IN 1 or AV IN 2 is selected for either the • The LCD display is defaulted to display the for the Front and Rear Speakers and TFT front or rear source, the other AV source is not
