Resumo do conteúdo contido na página número 1
OWNER'S MANUAL
Water Softener
With High Performance Valve
IntelliSoft 420 Series
MODEL NO. 625.384260
Caution:
• Warranty
Read and follow all safety rules and operating
• Installation
instructions before first use of this product.
Timer
• Start Up / Setting
Questions ?
• How It Works
Visit www. KenmoreWater.com
or call toll free 1-800-426-9345 (M - F, 7 AM - 6 PM CST)
• Care Of
Repair or Parts ? Call toll free 1-800-469-4663
• Specifications
See back cover for other Sears service numbers.
• Repa
Resumo do conteúdo contido na página número 2
WARRANTY ON WATER SOFTENER ONE YEAR LIMITED WARRANTY ON WATER SOFTENER When installed, operated and maintained according to all instructions supplied with the product, if this Kenmore Elite appliance fails due to a defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ®to arrange for free repair. THREE YEAR LIMITED WARRANTY ON ELECTRONIC PARTS When installed, operated and maintained according to all instructions supplied with the product, if any of th
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS Safety Guides .................................................................................................................................................. 4 Unpack and Check Shipment ........................................................................................................................ 5 Plan Your Installation: Tools Needed, Materials Needed ........................................................................... 6-10 Install Inlet/Outlet Adapters or B
Resumo do conteúdo contido na página número 4
Read all steps, guides and rules carefully before installing and using your new water soften- er. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water softener. Your Kenmore Water Softener will remove hardness minerals from water. This is measured in grains per gallon (gpg). It will also remove some clear water iron*, barium and radium 226/228"*. These
Resumo do conteúdo contido na página número 5
INSPECT SHIPMENT Your water softener is shipped complete in one carton. Use care when handling the softener. DO NOT turn upside down. DO NOT drop, or set on sharp objects that could make a hole in the bottom. The water softener is heavy, do not try to lift it or move more than is necessary. Remove all items from your shipping carton. Check all items against the packing list below. Note any items lost or damaged in shipment. Note any damage to the shipping carton. Refer to the exploded view and p
Resumo do conteúdo contido na página número 6
PLAN YOUR INSTALLATION It is recommended to read through the entire manual before beginning your installation. Follow all steps exactly. Reading this manual will also help you get all the benefits from your system. TOOLS NEEDED: • Safety glasses • Flathead screw driver • Phillips screw driver • Adjustable slip joint pliers • Tape measure or ruler J Flathead Screwdriver Safety Glasses Phillips Screwdriver Adjustable Slip Joint Pliers Tape Measure or Ruler ADDITIONAL TOOLS NEEDED FOR THE FOLLOWING
Resumo do conteúdo contido na página número 7
outside faucet outside faucet (hard water) (hard water) to R.O. faucet soft, cold water soft, hot water Soft water to Reverse Shut-off Osmosis Valve system R.O. water storage heater tank water meter softener water / gap floor main drain shutoff valve FIG. 3 Typical Installation WHERE TO INSTALL THE WATER SOFTENER Review the following points before you choose a place to put your softener. 1. Place as close as possible but always after, the 6. Put the softener in a place where water damage is pres
Resumo do conteúdo contido na página número 8
Suggested Slab Foundation Installation outside - hard water heater kitchen Plug the softener transformer bathroom into an inside, 120 volt 60Hz electrical outlet. If an outside outside For outside hard outlet is used, be sure it has -soft water, trench under- approved weather protection. ground as needed. outside bypass - hard valve outside -soft WATER SOFTENER (install in garage, car port, or other sheltered area) water in Run drain tubing to laundry tub or p-trap inside home, if possible. FIG.
Resumo do conteúdo contido na página número 9
PIPE, FITTINGS, OTHER MATERIALS NEEDED You must first decide how to run "in" and "out" pipes to the softener. Look at your house main water pipe at the OUT IN point you will connect the softener. Is the pipe soldered copper, glued plastic, or threaded galvanized or brass? 1" NPT sweat What is the pipe size? What kind of pipe and fittings is it Use teflon tape, adaptor (2)* easiest for you to work with, and what tools do you have? pipe joint compound. or both. 1" NPT adaptor 2 of each Now look at
Resumo do conteúdo contido na página número 10
BEFORE INSTALLING CHECKS & TESTS If you have a well water system, look at the pressure Your water supply needs to be checked for chemical gauge to find the water pressure. Call your local water analysis, water pressure and water flow rate. To accom- department if you have city water. They will tell you what plish this, complete the following steps: the water pressure is where you live. NOTE: Add these readings to the Facts and Figure Check Water's Chemical Analysis: Sears sells a com- table on p
Resumo do conteúdo contido na página número 11
ASSEMBLE INLET OUTLET ADAPTORS, Shutoff Shutoff . Pressure OR SINGLE BYPASS VALVE Valve Valve d/ Tank Complete the following steps to assemble the adaptors or bypass valve. 1. Close the shutoff valve on the house main water pipe, near the water meter or pressure tank, to turn off the water. See Fig. 7. Pump 2. Shut off the gas or electric supply to the water heater. See Fig. 7. 3. Open the highest and lowest water faucets in your Electrical Panel house. This will let water drain from the pipes.
Resumo do conteúdo contido na página número 12
INSTALLING HOLDING CLIPS Black Clip Cross Section of Valve Inlet or Outlet Bypass Valve or Installation Adaptor Before installing the bypass valve, or copper tube, be sure the turbine and support are firmly in place in the valve outlet port. Turbine Sensor Port Support / O-Ring Clip Snaps into Place Between Larger Diameter Rings FIG. 11 BYPASS VALVE TURNED DOWNWARD \ Turbine FIG. 10 Turn bypass valve upside down to connect to floor level plumbing. OUT IN t FIG. 12 3 VALVE BYPASS INSTALLING 3 VAL
Resumo do conteúdo contido na página número 13
POSITION SOFTENER INTO PLACE Complete the following steps to position the softener. MOVE SOFTENER INTO PLACE 1. Grip under the ridge on the salt tank sidewall. 2. Carefully rock back and forth into position. 3. Move the softener into position. 4. Place on a level and smooth surface. If needed, put a piece of 3/4" plywood, at least 17" x 20", under the Grip under ridge tank. Then put spacers under the plywood to level the to move softener. softener. See Fig. 14. NOTE: Do not put shims or spacers
Resumo do conteúdo contido na página número 14
CONNECT THE VALVE DRAIN HOSE per tube is also best to use for an overhead drain. Use a copper drain tube if the softener is installed outside, Take a length of 3/8" inside diameter drain tubing and or in the sunlight. Heat from the sun can soften, flatten attach one end to the drain fitting. See Fig. 16. Use a and close up some kinds of tubes. tube clamp to hold it in place. Put the other end of the tubing over a floor drain, into a laundry tub, standpipe, To adapt a copper drain tube to the sof
Resumo do conteúdo contido na página número 15
LEAK TEST To check for leaks, complete the following steps: HOUSE MAIN WATER SHUTOFF VALVES CAUTION: To avoid water or air pressure dam- age to softener inner parts, and to flush pipe chips or other residue from the water pipes, be Shu_ sure to do the following steps exactly as instructed. Water ¢--_% Pressure Tank 1. Fully open two cold, soft water faucets near the softener. Meter Shutoff _ Valve / d"- 2. Look at the pictures in Fig. 18 and 19 to deter- Well Pump mine your kind of bypass valve(
Resumo do conteúdo contido na página número 16
INSTALLGROUNDINGCLAMPBETWEEN COLD WATER PIPE GROUNDING THESOFTENERINAND OUT PIPES The house cold water pipe (iron or copper) is often TO Valve Inlet used to ground all electrical outlets in the home. Outlets are grounded to protect you from shock when Ground you touch any electric appliance plugged into the out- let. If you installed the single bypass valve, the cold Clamp (2% water pipe ground is broken. See Fig. 20 and 21. IMPORTANT: Be sure the cold water pipe has J direct metal to metal cont
Resumo do conteúdo contido na página número 17
INSTALL COVERS Salt Hole After installing your water softener, replace the covers. Cover Cover Angle the covers so the main cover clips onto the back (Main) first, then bring down in front and clip on the two (2) tabs inside the rim of the salt hole and lower the salt cover closed. See Fig. 23. RESTART THE WATER HEATER Turn on the gas (or electric) supply to the water heater and light the pilot. YOUR PLUMBING INSTALLATION AND ELECTRICAL WORK ARE NOW COMPLETE. FIG. 23 REGENERATION Button Display
Resumo do conteúdo contido na página número 18
SET PRESENT TIME OF DAY Present Time: Present Time: If the words PRESENT TIME do not show in the display, _Av _PM press the SELECT button until they do show in the display. Press the UP or DOWN buttons to set the present time. Press UP to move the display ahead; press DOWN to move /_ V CHANGE SELECT A V CHANGE SELECT the time backward. If the present time is between noon and midnight, be sure PM shows. If the present time is between FIG. 26 midnight and noon, be sure AM shows. Each press of the
Resumo do conteúdo contido na página número 19
SET REGENERATION TIME Recharge Time: To complete setting the regeneration time, complete the follow- ing steps: 1. Press the SELECT button to display 2:00 AM (flashing) and RECHARGE TIME. /_ V CHANGE SELECT FIG. 28 2. At the 2:00 AM recharge time setting, the softener begins regeneration (see pages 29 - 31) at 2:00 AM. This is a good time in most households because water is not being used. If a different recharge time setting would be better for your household, complete the following step. 3. Pr
Resumo do conteúdo contido na página número 20
SANITIZE THE WATER SOFTENER Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, or cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the softener. ! SANITIZE YOUR WATER SOFTENER AS FOLLOWS: 1. Be certain the bypass valve is pulled out to "service" position. Brinewell Cover 2. Liftthe salt hole cover and use a pail add up
