Resumo do conteúdo contido na página número 1
COMMERCIAL HE DRYER INSTALLATION INSTRUCTIONS
(original instructions)
Gas
INSTRUCTIONS D’INSTALLATION D’UN SECHE-LINGE HE COMMERCIAL
(traduction des instructions d’origine)
À gaz
INSTRUCCIONES DE INSTALACIÓN – SECADORA HE COMERCIAL
(traducción de las instrucciones originales)
A gas
ISTRUZIONI D’INSTALLAZIONE – ASCIUGATRICE HE COMMERCIALE
(traduzione delle istruzioni originali)
A gas
MDG22PN MDG22PD
W10239207B
www.maytagcommerciallaundry.com
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS DRYER SAFETY ............................................................................3 INSTALLATION INSTRUCTIONS – GAS DRYER ....................9 DRYER DISPOSAL ........................................................................4 Install Leveling Legs....................................................................9 INSTALLATION REQUIREMENTS ..............................................4 Make Gas Connection..........................................................
Resumo do conteúdo contido na página número 3
DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean: You can be killed or seriously injured if you don't immediately
Resumo do conteúdo contido na página número 4
DRYER DISPOSAL INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed: 5 200 mm (8") or 250 mm 8 mm ( /16") socket wrench (10") Pipe wrench Utility knife 200 mm (8") or 250 mm Vent clamps (10") Adjustable wrench Pipe-joint compound Flat-blade screwdriver resistant to LP gas Phillips screwdriver Sealing gun and sealing Ad
Resumo do conteúdo contido na página número 5
159 mm Recessed Area and Closet Installation Instructions 1 (6 /4") This dryer may be installed in a recessed area or closet. This dryer must not be installed behind a lockable door, a sliding door, or a door with a hinge on the opposite side to that of the dryer. ELECTRIC The installation spacing is in millimeters and is the minimum allowable. Additional spacing should be considered for ease of installation, servicing, and compliance with local codes and ordinances. 715 mm If installed in a clo
Resumo do conteúdo contido na página número 6
This dryer is supplied/fitted with an electricity supply cord and plug. It Using the universal cord included with this dryer: should be connected to electricity supply socket at the voltage shown The gas dryer is equipped with a universal cord with on the rating plate. The minimum supply fuse capacity should be 5A. interchangeable plugs. The dryer must be positioned so that the plug is clearly visible and accessible. This plug also provides the function of an emergency stop 1. To use the univers
Resumo do conteúdo contido na página número 7
Natural Gas: Venting Requirements This dryer is factory adjusted for use with NATURAL GAS (G20), and no further adjustment should be required at installation. L.P. Gas: WARNING This dryer is also certified for use with L.P. (propane or butane) gases with appropriate conversion. No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. Conversion must be done by a competent se
Resumo do conteúdo contido na página número 8
Plan installation to use the fewest number of elbows and turns. Each vent should enter the main vent at an angle pointing in the direction of the airflow. Vents entering from the opposite side should be staggered to reduce the exhausted air from interfering with the other vents. The maximum angle of each vent entering the main vent should A B be no more than 30°. A 30˚ max. Exhaust Air Flow A. Good B air !ow B. Better Allow as much room as possible when using elbows or making turns. Bend vent gr
Resumo do conteúdo contido na página número 9
INSTALLATION INSTRUCTIONS – GAS DRYER Install Leveling Legs Connect Vent 1. Using a 102 mm (4") clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 102 mm (4") clamp. 2. Move dryer into final position. Do not crush or kink vent. Make sure dryer is level. 3. Check to be sure there are no kinks in the flexib
Resumo do conteúdo contido na página número 10
MAINTENANCE INSTRUCTIONS Maintenance instructions: If dryer does not operate, check the following: Clean lint screen after each cycle. Electric supply is connected. Removing accumulated lint (disconnect dryer from electricity Circuit breaker is not tripped or fuse is not blown. and gas supplies before starting this task): Door is closed. Listen closely to hear door switches activate. • From inside the dryer cabinet: Selected cycle button has been pressed firmly and display Lint shoul
Resumo do conteúdo contido na página número 11
REVERSING THE DOOR SWING Door swing can be changed from a right-side opening to left-side 5. Rotate outer door 180°. opening, if desired. Place a towel or soft cloth on top of the dryer or work space to avoid damaging the surface. Remove the Door Assembly 1. Remove 3 of the 4 screws that hold the door hinge on the front panel of the dryer. Partially loosen the remaining screw with keyhole opening and lift the door off the screw. A. Loosen screw with Reverse Hinge keyhole opening 1. Use a small f
Resumo do conteúdo contido na página número 12
5. Place the inner door assembly inside the outer door assembly. 2. Remove the strike using a Phillips screwdriver. To fit correctly, the inner door assembly edge fits completely inside the outer door assembly edge. 3. Insert strike on the opposite side. 6. Reassemble the inner and outer door assemblies with the 6 screws. Reinstall the door 1. Reattach door to dryer front panel with the 4 screws. Partially install the screw with keyhole opening first, and fit the keyhole opening in the hinge ove
Resumo do conteúdo contido na página número 13
ELECTRONIC CONTROL SETUP Pricing After the door is opened and closed following the completion of a cycle, the display indicates the cycle price (unless set for free operation). As coins or debit inputs arrive, the display will change to lead the user through the initiation of a cycle. There are four (4) types of pricing: Fixed ‘Vend’ Pricing A dryer set up for ‘Fixed Cycle’ operation can only accept additional time accumulated by increments equal to the length of a complete dry cycle. A maximum
Resumo do conteúdo contido na página número 14
CONTROL SET-UP PROCEDURES DISPLAY IMPORTANT: Read all instructions before operating. After the dryer has been installed and plugged in, the display will show ‘0 minutes.’ The fabric setting buttons along with the digital display are used to set-up the dryer controls. Once the dryer has been plugged in and the dryer door opened and closed, the display will show the vend price. PN models are The display can contain 4 numbers and/or letters and a decimal factory preset for free cycles; the display
Resumo do conteúdo contido na página número 15
CODE EXPLANATION CODE EXPLANATION MONEY COUNTER OPTION OPTIONS TO USE IF SPECIAL PRICING IS SELECTED (continued): 1.00 This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’. SPECIAL PRICE START HOUR 7.0 0 Not Selected ‘OFF’. 1.00 NOTE: Uses the 24 hr. clock. Selected ‘ON’. 1.0C This is the start hour, 0-23 hours. Select START HOUR 7.0 0 by pressing WHITES AND COLORS button. Press DELICATES button 3 consecutive times to select ‘ON’ and 3 consecutive times to remove (Not Selected ‘OFF’.) Press
Resumo do conteúdo contido na página número 16
If cycle counter (9 0C) is selected, the following is true: CODE EXPLANATION 1 00 Represents the number of cycles in HUNDREDS. 1 02 = 200 COIN SLIDE OPTION 8.00 This option is either SELECTED ‘ON’ or NOT SELECTED ‘OFF’. 2 00 Represents the number of cycles in ONES. 2 25 = 225 Replacement of metercase will be needed for coin slide mounting. TOTAL CYCLES = 225 Not Selected ‘OFF’. 8.00 This is ‘VIEW ONLY’ and cannot be cleared. Selected ‘ON’. 8.CS NOTE: This option needs to be set to ‘00’ unless th
Resumo do conteúdo contido na página número 17
MAYTAG COMMERCIAL WASHER, DRYER, STACKED DRYER/ DRYER, COMMERCIAL STACK LAUNDRY, AND MULTI-LOAD COIN OPERATED COMMERCIAL WASHERS AND DRYERS WARRANTY LIMITED WARRANTY ON PARTS For the first five years from the date of purchase, when this commercial appliance is installed, maintained and operated according to the instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation (thereafter “Maytag”) will pay for factory specified parts or original equipment manufact
Resumo do conteúdo contido na página número 18
SECURITE DU SECHE-LINGE Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres. Tous les messages de sécurité suivront le symbole d’alerte de sécur
Resumo do conteúdo contido na página número 19
ELIMINATION DU SECHE-LINGE EXIGENCES D’INSTALLATION Outillage et pièces Rassembler les outils et pièces nécessaires avant de commencer l’installation. Lire et respecter les instructions d’installation fournies avec chacun des outils de cette liste. Pièces fournies Outillage nécessaire Retirer le sac de pièces du tambour du sèche-linge. Vérifier la Clé à tube de 200 mm (8") Couteau utilitaire présence de toutes les pièces. ou 250 mm (10") Brides de fixation Clé à molette de 200 mm Patin
Resumo do conteúdo contido na página número 20
Distances de séparation minimales Exigences d’emplacement AVERTISSEMENT 356 mm (14") max 381 mm (15") Porte du placard Risque d'explosion 0 mm 0 mm 0 mm (0") (0") (0") Garder les matières et les vapeurs inflammables, telle que l'essence, loin de la sécheuse.
25 mm (1") Ne pas installer dans un garage.
Placard, vue latérale Encastrement, vue avant Le non-respect de ces instructions peut causer un décès, une explosion ou un incendie. On doit prévoir un espacement additionnel pour tenir compte é
