Manual do usuário Cornelius 10

Manual para o dispositivo Cornelius 10

Dispositivo: Cornelius 10
Categoria: Geladeira
Fabricante: Cornelius
Tamanho: 0.67 MB
Data de adição: 9/21/2014
Número de páginas: 42
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Cornelius 10. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Cornelius 10.

Para sua conveniência

Se a consulta dos manuais Cornelius 10 diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Cornelius 10 no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Cornelius 10 em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Cornelius 10 Manual de instruções - Online PDF
Advertisement
« Page 1 of 42 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Cornelius 10, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Cornelius 10. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

AURORAR10,000 PLUS
COOLING UNIT
Installation Manual
Part No. 300614000
November 8, 1989
Revised: April 12, 1993
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment
PRINTED IN U.S.A
Ó IMI CORNELIUS INC; 1989--93

Resumo do conteúdo contido na página número 2

TABLE OF CONTENTS Page GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 COOLING UNIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SYSTEM THEORY OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . .

Resumo do conteúdo contido na página número 3

TABLE OF CONTENTS (cont’ d) Page ADJUSTING CO2 REGULATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ADJUSTING DISPENSING VALVES WATER FLOW RATE . . . . . . . . . . . . . 14 ADJUSTING WATER-TO-SYRUP ‘ ‘ RATIO’ ’OF DISPENSED PRODUCT . 14 ADJUSTING SIZE OF DRINK DISPENSED . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 REPLENISHING CO2 SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 REPLENISHING SYRUP SUPPLY . . .

Resumo do conteúdo contido na página número 4

TABLE OF CONTENTS (cont’ d) Page COOLING UNIT CO2 INLET LINE CO2 GAS CHECK VALVE . . . . . . . . . . . 27 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 WATER-TO-SYRUP ‘ ‘ RATIO’ ’OF DISPENSED DRINK TOO LOW OR TOO HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 ADJUSTMENT OF DISPENSING VALVE SYRUP FLOW REGULATOR DOES NOT INCREASE

Resumo do conteúdo contido na página número 5

GENERAL INFORMATION IMPORTANT: To the user of this manual - This manual is a guide for installing, operating, and maintaining this equipment. Refer to Table of Contents for page location of detailed information pertaining to questions that arise during installation, operation, service and maintenance, or troubleshooting this equipment. GENERAL DESCRIPTION This section gives the description, theory of operation, and design data for the AuroraR10,000 Plus Cooling Unit, hereafter referred too as a

Resumo do conteúdo contido na página número 6

Table 1. Design Data COOLING UNIT DATA Model No. 416654 Overall Dimensions: Height 25-inches Width 36-1/2 inches Depth 24-1/2 inches NOTE: Overall dimensions if Cooling Unit is placed on optional Cooling Unit Stand (P/N 309309069). Height (approximate) 72-5/16 inches Width 37-1/2 inches Depth 25-3/8 inches Weights: Shipping 385 pounds Dry Weight pounds Ice Bank Weight 40 ±pounds Capacities: Water Bath (no ice bank) 18 gallons Compressor Horsepower 2 HP Refrigeration System: Refrigerant Type and

Resumo do conteúdo contido na página número 7

SYSTEM THEORY OF OPERATION (see Figure 2) A CO cylinder delivers carbon dioxide gas (CO ) to primary CO regulator assembly which deliver regulated 2 2 2 CO gas to adjustable secondary CO regulators. Secondary CO regulators delivers regulated CO gas to the 2 2 2 2 carbonated water tank inside the Cooling Unit and also to the soft drink tanks. Plain water enters the Cooling Unit and is pumped through and is pre-cooled by the refrigerated Hydro Boostâ coil. Cooled water continues through the plain

Resumo do conteúdo contido na página número 8

300614000 4 DOUBLE LIQUID COOLING UNIT SHUTOFF CHECK VALVE ASS’ Y(2) WATER FILTER VALVE ASS’ Y CARBONATED WATER TANK ASS’ Y PLAIN WATER DIET SYRUP SOURCE CO REGULATOR 2 TO WATER PRESSURE SUGAR SYRUP DISPENSING REGULATOR CO REGULATOR STATION 2 HYDRO BOOSTR CARBONATOR BYPASS SHUTOFF CO REGULATOR 2 VALVE CO MANIFOLD 2 CO GAS CHECK HYDRO BOOSTR 2 VALVE(10) COIL LIQUID CHECK VALVE PRIMARY CO REGULATOR 2 *WATER TANK WATER LEVEL CONTROL CARBONATED WATER PLAIN CO 2 CIRCULATING PUMP WATER PUMP CHECK VALV

Resumo do conteúdo contido na página número 9

INSTALLATION This section covers unpacking and inspection, selecting location, installing the Cooling Unit and the Remote Condenser Coil and Fan Assembly preparing for operation, and operation. UNPACKING AND INSPECTION NOTE: The Cooling Unit and the Remote Condenser Coil and Fan Assembly were thoroughly inspected before leaving the factory and the carrier has accepted and signed for them. Any damage or irregularities should be noted at time of delivery (or not later than 15 days from date of del

Resumo do conteúdo contido na página número 10

fused as indicated on the Unit nameplate. The power circuit may also be wired through an equivalent HACR type circuit breaker rather then the disconnect switch. THE POWER CIRCUIT MUST BE MADE UP OF COPPER CONDUCTORS AND ALL WIRING MUST CONFORM TO NATIONAL AND LOCAL ELECTRICAL CODES; (4) Close to a plain water source supply line with proper requirements; (5) Sufficient space around Cooling Unit (see Figure4) for proper air circulation (18-inches on sides and back, front side open to room, and top

Resumo do conteúdo contido na página número 11

CONNECTING ELECTRICAL POWER CIRCUIT TO COOLING Unit (see Figures 5 and 9) IMPORTANT: Before 208/230VAC single-phase 60Hz electrical power circuit is connected to the cooling unit, service power voltage entering the building must be identified. Service power voltage entering the building will either be 208 or 230VAC and may be posted on the main service box. If not, the installer must contact the local electrical power company for information. If these two voltage identification attempts should f

Resumo do conteúdo contido na página número 12

CONNECTING ELECTRICAL POWER CIRCUIT TO REMOTE CONDENSER COIL AND FAN ASS’ Y (see Figure 5 and 9) CAUTION: The Cooling Unit refrigeration system is cooled by a Remote Condenser Coil and Fan Assembly (P/N 309602000) that is authorized by IMI Cornelius Inc. Use of an unauthorized Remote Condenser Coil and Fan Assembly will automatically void the Cooling Unit factory warranty. NOTE: Electrical power circuit may be connected to the Remote Condenser Coil and Fan Assembly (P/N 309602000) in two ways. T

Resumo do conteúdo contido na página número 13

2. Connect flexible plain water inlet supply line (1/2-inch I.D. min.), meeting water inlet supply line requirements of preceding CAUTION note, to Cooling Unit 3/8-in. flare (5/8-18) bulkhead fitting on back of Unit labeled ‘ ‘ WATER INLET’ ’ . DO NOT OPEN WATER INLET SUPPLY LINE SHUTOFF VALVE AT THIS TIME. CONNECTING CO INLET SUPPLY LINE TO COOLING UNIT 2 (see Figure 2) WARNING: CO displaces oxygen. Strict attention must be observed in the prevention of 2 CO (carbon dioxide) gas leaks in the en

Resumo do conteúdo contido na página número 14

18--IN. COOLING UNIT 18--IN. 18--IN. AIR FLOW (OPEN TO ROOM) FIGURE 4. COOLING UNIT SPACE REQUIRED PLACING COOLING UNIT IN OPERATING POSITION 1. Very carefully, move Cooling Unit back into operating position leaving space around Unit (see Figure 4) as specified in SELECTING LOCATION. MAKE SURE THERE ARE NO KINKS IN COOLING UNIT INLET LINES, AND (IF APPLICABLE) REMOTE CONDENSER AND FAN ASSEMBLY REFRIGERATION LINES. NOTE: To comply with National Sanitation Foundation (NSF) requirements, Cooling Un

Resumo do conteúdo contido na página número 15

5. Adjust carbonator secondary CO regulator (see Figure 2) to a nominal 90-psi. Loosen CO regulator 2 2 adjusting screw locknut. Turn adjusting screw to the right (clockwise) until regulator gage registers nominal 90-psi, then tighten adjusting screw lock nut. CO PRESSURE TO CARBONATORS MUST NOT EXCEED 2 120-PSIG. OPERATION WARNING: Disconnect electrical power to Cooling Unit and Remote Condenser Coil and Fan Assembly to prevent personal injury before attempting any Cooling Unit or Remote Conden

Resumo do conteúdo contido na página número 16

Low-Calorie (diet) Syrup Soft Drink Tank CO Regulator. 2 Adjust low-calorie (diet) soft drink tank secondary CO regulator for low-calorie drink at 10-psig for 2 syrup lines up to 30-feet in length. Syrup lines longer than 30-feet in length may require a slightly higher CO regulator setting to 12-psig maximum. Excessive CO pressure may cause low-calorie syrup 2 2 carbonation resulting in foam. IMPORTANT: Syrup systems must be sanitized as instructed before syrup is connected into syrup systems. 1

Resumo do conteúdo contido na página número 17

OPERATORS INSTRUCTIONS This section covers operating controls, daily pre-operation check, adjustments, replenishing CO and syrup 2 supplies, cleaning and sanitizing, Cooling Unit maintenance, Remote Condenser Coil and Fan Assembly maintenance, lubrication, and servicing CO gas check valves. 2 WARNING: Disconnect electrical power to Cooling Unit and Remote Condenser Coil and Fan Assembly to prevent personal injury before attempting any internal maintenance. Only qualified personnel should service

Resumo do conteúdo contido na página número 18

DAILY PRE-OPERATION CHECK 4. Make sure CO cylinder regulator assembly 1800-psi gage indicator is not in shaded (‘ ‘ change CO 2 2 cylinder ’ ’ ) portion of dial. If so, CO cylinder is almost empty and must be replaced. 2 5. Sufficient syrup supply in all soft drink tanks. If not, replenish syrup supply as instructed. ADJUSTMENTS ADJUSTING CO REGULATORS 2 CO regulators should be periodically checked for proper pressure settings and if necessary, adjusted as 2 instructed. ADJUSTING DISPENSING VALV

Resumo do conteúdo contido na página número 19

SANITIZING SYRUP SYSTEMS Syrup systems should be sanitized every 90 days as instructed following Sanitizer Manufacturer ’ s recommendations. COOLING UNIT MAINTENANCE COOLING UNIT AIR INTAKE AND EXHAUST FILTERS CAUTION: Air filters on the Cooling Unit must be removed and cleaned every 30 days as instructed. Excessive accumulation of dust, lint, and grease on the air filters will restrict airflow through the Unit which will cause the refrigeration system to overheat. The Cooling Unit cabinet is eq

Resumo do conteúdo contido na página número 20

REMOTE CONDENSER COIL AND FAN ASS’ Y MAINTENANCE (see Figure 5) CAUTION: Remote Condenser Coil and Fan Assembly connected to the Cooling Unit is equipped with a condenser coil that must be cleaned every 30-days. Allowing condenser coil to become clogged will cause refrigeration system to overheat which will automatically shut refrigeration system down. After condenser coil has been cleaned, high-pressure cutout sensing switch (see Figure 5) will have to be pressed to restart refrigeration system


Manuais similares
# Manual do usuário Categoria Baixar
1 Cornelius CH Series Manual de instruções Geladeira 0
2 Cornelius CH1500-CH7500 Manual de instruções Geladeira 2
3 Cornelius CH 551 Manual de instruções Geladeira 0
4 Cornelius CH 1502-A Manual de instruções Geladeira 3
5 Cornelius CH 1503-A Manual de instruções Geladeira 0
6 Cornelius CH 1500-A Manual de instruções Geladeira 1
7 Cornelius CH751 Manual de instruções Geladeira 1
8 Cornelius CH750 Manual de instruções Geladeira 0
9 Cornelius CH550 Manual de instruções Geladeira 0
10 Cornelius Chiller ("CH" Series) CH 251 Manual de instruções Geladeira 1
11 Cornelius CH951 Manual de instruções Geladeira 0
12 Cornelius Chiller ("CH" Series) CH 250 Manual de instruções Geladeira 0
13 Cornelius REACH-IN REFRIGIRATOR COR20RRTM Manual de instruções Geladeira 0
14 Cornelius REACH-IN REFRIGIRATOR COR40RRTMD Manual de instruções Geladeira 3
15 Cornelius REACH-IN REFRIGIRATOR COR22RRTM Manual de instruções Geladeira 0
16 2JANE Surround Sound System HTS-GS1 Manual de instruções Geladeira 4
17 3Com Phaser 7750 Manual de instruções Geladeira 1
18 3Com iQ 10 Manual de instruções Geladeira 0
19 3Com PowerDual iQ 10 iQ 10C Manual de instruções Geladeira 1
20 3Com PowerDual iQ 10 iQ 10P Manual de instruções Geladeira 2