Resumo do conteúdo contido na página número 1
Frigorifero/congelatore
Model:
da incasso
LB30AFNF
Manuale di installazione
FB30AFNF
Built-in Fridge/Freezer
Installation Manual
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
20 Contents 1. Note before installing .............................................................. 21 2. Components to install .............................................................. 22 3. Assembly/Disassembly diagram of Built-in refrigerator ............ 23 4. Dimension of Built-in refrigerator and furniture ....................... 24 5. Installing the built-in refrigerator ............................................. 25 6. Procedure to install 1) Preparing before installing the refr
Resumo do conteúdo contido na página número 4
21 1. Note before installing Caution Install the product at the place avoiding the heat from the heater or the boiler or the direct sunlight, with the shade and the good ventilation always. Prepare the furniture possible to circulate air by referring to the size. Install the product for air to smoothly flow via the front intake hole. If not, it may cause to prevent the normal performance of the product. Install the product at the place where no outsider enters or exits because it may damage t
Resumo do conteúdo contido na página número 5
22 2. Components to install Top cover of refrigerator Hinge holder Depth adjusting bracket Depth adjusting bracket (diameter = 5.5mm) (diameter = 8mm) Qty: 1EA Qty: 1EA Qty: 2EA Qty: 2EA Hinge bracket Hinge bracket cover Paper jig Top bracket of furniture door Qty: 1EA Qty: 1EA Qty: 1EA Qty: 1EA Depth adjusting bracket Depth adjusting bracket cover Depth adjusting bracket cover Top bracket cover of furniture door Qty: 2EA Qty: 2EA Qty: 2EA Qty: 1EA Cap screw Front cover of hinge V
Resumo do conteúdo contido na página número 6
23 3. Assembly/Disassembly diagram of Built-in refrigerator
Resumo do conteúdo contido na página número 7
554mm 400mm 570mm Inner dimension 400mm or longer 600mm 595mm 400mm or longer 24 4. Dimension of Built-in refrigerator and furniture The entire furniture thickness shown at this figure is based on 15mm. The furniture dimension should comply with the figure. 1775 mm 1830mm 1688.5 mm or longer 1800mm or longer Inner dimension 39mm 50mm Caution When the furniture thickness is changed, the door size of the furniture is changed. Furniture thickness Furniture door size 18mm 1836mm or longer 20mm
Resumo do conteúdo contido na página número 8
Wall Wall Wall 25 5. Installing the built-in refrigerator The minimum space for ventilating should be prepared for the smooth heat exchange of the refrigerator. 2 1. It should be structured for air to enter from the intake hole and to exit from Ceiling the discharge hole. min. 50mm 1 2. The passage ¡ should be secured when the passage ¨ is not secured. 2 3. 200cm or more of the air ventilation at ¨ and ¡ should be secured. min. 30mm Caution Requirements for the furniture floor - Floor: We recom
Resumo do conteúdo contido na página número 9
26 6. Procedure to install 1) Preparing before installing the refrigerator 1. Installing the top cover of the refrigerator 1) Fold the top cover of the refrigerator ¨ in advance as shown at the figure. 1 2) Fix the top cover of the refrigerator ¨ at the place by 45mm from the end of the furniture with the wood screws (three 1 spots). (If the thickness of the furniture is 18mm or 20mm, cut and install the top cover of b the refrigerator ¨ as described at the following “Reference“.) Referenc
Resumo do conteúdo contido na página número 10
27 6. Procedure to install 1) Preparing before installing the refrigerator 2. Insert the hinge base into the hinges (two spots). (See Figure 1) (If the thickness of the furniture is 20mm, do not install the hinge base .) 3. Tilt backward the refrigerator and loosely fix the height adjusting bracket at the bottom (two spots) of the refrigerator door by using the hinge screws as shown at the figure. (Figure 1) 2 2 3 e 3 e 2) Case related work after placing the refrigerator 4. Put out the powe
Resumo do conteúdo contido na página número 11
Front of furniture 28 6. Procedure to install 2) Case related work after placing the refrigerator 6. Adjust the horizontal/vertical level of the refrigerator by turning the level adjusting leg( ). When the top side is deep The refrigerator is tilted backward, so turn counterclockwise the level adjusting leg to adjust the level. When the bottom side is deep The refrigerator is tilted forward, so turn clockwise the level adjusting leg to adjust the level. Use the spanner to make sur
Resumo do conteúdo contido na página número 12
29 6. Procedure to install 2) Case related work after placing the refrigerator 7. Make sure that the end of the hinge base is aligned with the front right of the furniture. Furniture Hinge base Hinge Front side of the furniture 8. Fix the top hinge and the bottom hinge by (Figure 3) the hinge screws (four spots). (See Figure 3) When fixing the screws, be careful of being f damaged by the hinge operation. 9. Use the ruler to make sure that the left depth and the right depth are constant as
Resumo do conteúdo contido na página número 13
30 6. Procedure to install 2) Case related work after placing the refrigerator 10. Open the refrigerator door, place the hinge (Figure 5) bracket at the top left of the refrigerator, and fix them at the furniture and the e refrigerator respectively with the wood screw (one spot) and the bracket screws (two 5 b spots). (See Figure 5) 11. Insert the hinge bracket cover from the left (Figure 6) and then press it. (See Figure 6). 6 Reference If the furniture thickness is 15mm, about 6mm of gap
Resumo do conteúdo contido na página número 14
31 6. Procedure to install 3) Furniture door related work 12. Place the paper jig on the reference line of the paper jig at the rear side of the furniture door. (See Figure 7) Reference - Place the reference line of the paper jig at 1595mm from the floor of the furniture. - If the furniture door is long, place the reference line of the paper jig at 1595mm plus ‘A’ from the floor of the furniture. (Figure 7) Reference line Reference line of paper jig (for of paper jig (for the right hinge) th
Resumo do conteúdo contido na página número 15
32 6. Procedure to install 4) Refrigerator door related work 15. Insert the height adjusting nuts (two spots at the bottom) into the height adjusting screw, and then place the top bracket of the furniture door at the height adjusting screw of the top of the refrigerator door. Use the height adjusting nut to adjust the height of the furniture door and set the level. (See Figure 10) (Figure 10) When installing the furniture door, be careful of being injured or damaging the furniture door when t
Resumo do conteúdo contido na página número 16
33 6. Procedure to install 4) Refrigerator door related work 17. Loosely fix the top bracket with the height adjusting nuts (Figure 13), and adjust the depth gap between the furniture door and the front of the furniture to 4mm. At this time, adjust the location of the furniture door for the furniture door not to touch the furniture when opening/closing the door. d 8 (Figure 13) 18. Use the spanner to check the dimension. (See Figure 15) (Figure 14) Parallel Cooling room Parallel Furniture
Resumo do conteúdo contido na página número 17
34 6. Procedure to install 4) Refrigerator door related work 21. Move the furniture door to the depth (Figure 16) direction to adjust the depth gap to 4mm (See Figure 14), and fix the depth adjusting bracket to both sides (two spots) of the 9 refrigerator door with the door screw . (Figure 16) a 22. Use the wood screws (four spots) to the depth adjusting bracket , move the furniture door to the depth direction to adjust the depth gap to 4mm (See Figure 14, Figure 17), and secure the loosely
Resumo do conteúdo contido na página número 18
Refrigerator side 35 6. Procedure to install 5) Installation checkup and finishing work 24. Insert the font cover of the hinge into the front of the inside. (two spots) 25. Insert the ventilation cover into the rectangular floorcloth pan. 26. Attach the gasket as shown at the figure. Attach it to the opposite side from the hinge side. If the gasket is long, cut it 1800mm according to the length to use. 27. Insert the cap screw as shown at the figure. 16 14 16 16 13 14 15 (Figure 19)
Resumo do conteúdo contido na página número 19
36 6. Procedure to install 6) Changing the opening direction of the refrigerator door Before installing, change the door to work. 1. Loosen the screws and at the hinge of the case section, and push the door to the right to disconnect. (See Figure 20) 2. Completely loosen the screws and , and then fix them at the opposite side loosely. (See Figure 20) 3. Loosen the screws and fixed to the door to disconnect (Figure 20) the hinge. 4. Move the disconnected hinge to the diagonal direction
Resumo do conteúdo contido na página número 20
5mm 37 6. Procedure to install 7) Furniture door gap When installing two pieces of furniture closely, keep the gap between them 5mm or more.
