Resumo do conteúdo contido na página número 1
Planning Information
Built-In Model 650G
Over-and-Under Refrigerator/Freezer with Glass Door
Front venting allows Hermetically sealed
unit to be completely refrigeration units
built in
Serial and model
number plate
Lighted electronic
control panel
Triple-pane
UV resistant low-
Adjustable spill-proof
energy glass door
glass shelves
Model 650G/F
Framed
Egg container
High humidity
crisper drawer
Automatic ice maker Four-sided
Magnetic gaskets
Model 650G/O
Overlay
Two-tier wire Door closers
storage
Resumo do conteúdo contido na página número 2
Planning Information Built-In Model 650G FEATURES 36" (914) wide over-and-under refrigerator/ Door alarm will let you know with an audible freezer with glass door beeping if your refrigerator door or freezer drawer are left ajar Framed, overlay and stainless steel applica- tions provide complete design flexibility Automatic ice maker provides an ample supply of crescent-shaped ice Sub-Zero's dual refrigeration system ensures the freshest food and energy efficiency Triple-pane UV-resistant low-e
Resumo do conteúdo contido na página número 3
Planning Information Built-In Model 650G SPECIFICATIONS Model 650G Over-and-Under Refrigerator/Freezer with Glass Door Overall Width 36" (914) Overall Height 84" (2134) MODEL OPTIONS Overall Depth 24" (610) Framed Design 650G/F Refrigerator Capacity 16.0 cu ft (453 L) Overlay Design 650G/O Freezer Capacity 4.9 cu ft (139 L) Classic Stainless Steel 650G/S Minimum Height (levelers in) 83" (2108) Platinum Stainless Steel 650G/P 1 Door Swing Clearance 36 /16" (916) Carbon Stainless Steel 650G/B Elec
Resumo do conteúdo contido na página número 4
Planning Information Built-In Model 650G INSTALLATION SPECIFICATIONS 24" EXTEND WATER LINE (610) APPROX. 36" (914) ROUGH FROM BACK WALL OPENING DEPTH SHUT-OFF VALVE TOP VIEW 7" E (178) 6" (152) LOCATE ELECTRICAL WITHIN SHADED AREA 1 35 /2" (902) ROUGH OPENING WIDTH 3 1 83 /4" 75 /2" (2127) (1918) ROUGH OPENING HEIGHT WITH STANDARD 11" (279) GRILLE LOCATE WATER SUPPLY WITHIN SHADED AREA 3" (76) 18" 6" (457) (152) W FRONT VIEW DIMENSIONS 1 Finished Rough Opening
Resumo do conteúdo contido na página número 5
Planning Information Built-In Model 650G INSTALLATION NOTES Refer to the illustrations and specifications A line filter is required when water condi- for overall dimensions, finished rough opening tions have a high sediment content. The ice dimensions and installation specifics. maker operates on water pressure of 20 psi (1.4 bar) to 100 psi (6.9 bar). In some cases a Allow the door to open a minimum of 90˚ or reverse osmosis water filter system may not be you'll have problems removing drawers.
Resumo do conteúdo contido na página número 6
Planning Information Built-In Model 650G ADDING PANELS In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front door panels. FRAMED PANELS If you and your client have ordered a framed or overlay 1 design model, you will be adding panels to give the unit PANELS /4" (6) TH
Resumo do conteúdo contido na página número 7
Planning Information Built-In Model 650G FRAMED PANELS The refrigerator door panel must include a cut-out to accommodate the window. Refer to the chart below for exact dimensions. The glass portion of the door must be exposed and not covered by any part of the panel. An 11" (279) louvered grille is standard on framed applica- H tions. Optional louvered grilles are available in 1" (25) height increments from 10" (254) to 15" (381). C You may choose to use Sub-Zero's optional panel grille for C C
Resumo do conteúdo contido na página número 8
Planning Information Built-In Model 650G OVERLAY PANELS The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels—the 1 decorative overlay panel, a .10" (3) spacer panel and a /4" OVERLAY PANELS (6) backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or more likely, three different panels.
Resumo do conteúdo contido na página número 9
Planning Information Built-In Model 650G OVERLAY PANELS The refrigerator door panel must include a cut-out to accommodate the window. Refer to the chart below for exact dimensions. The glass portion of the door must be exposed and not covered by any part of the panel. An 11" (279) panel grille is standard on overlay applica- H tions. Optional panel grilles are available in 1" (25) height increments from 10" (254) to 15" (381). A A A OVERLAY PANEL DIMENSIONS H WIDTH HEIGHT 7 7 Refrigerator Door P
Resumo do conteúdo contido na página número 10
Planning Information Built-In Model 650G OVERLAY PANELS IMPORTANT NOTE: For overlay door panels, it is neces- sary to rout a space for the unit‘s lower hinge plate so that it does not strike the door panel. Refer to the top illustration on this page. You will minimize the reveal between the bottom of the OVERLAY PANELS overlay door panel and the top of the overlay drawer panel. Refer to the bottom illustration on this page. Overlay Panel If you choose not to rout a space for the lower hinge plat
Resumo do conteúdo contido na página número 11
Planning Information Built-In Model 650G SIDE PANELS Side panels can be used with the framed, overlay and stainless steel design applications. When planning for side panels with the installation of the Built-In model, you need to be aware of space configuration to achieve a pleasing fit. Depending on the exact panel you are using with your SIDE PANELS unit, the height of the panel will vary. Cut-outs around the toe kick and grille area are required if 1 a /4" (6) thick panel will be inserted int
Resumo do conteúdo contido na página número 12
Planning Information Built-In Model 650G HANDLE PROFILE – FRAMED APPLICATION OPTIONAL EXTENDED FULL-LENGTH HANDLE 1" 2" 3" (25) (51) (76) 1 1 /4"(32) PANEL STANDARD FULL-LENGTH 1"(25) PANEL HANDLE 3 /4"(19) PANEL 1 /2"(13) PANEL 1 /4"(6) PANEL 1 /4"(6) FRAMED PANEL DOOR FULL-SCALE TEMPLATES HANDLE PROFILE The following full-scale illustrations enable you The full-scale illustration above shows handle to understand some of the unique situations placement for the framed application standard you
Resumo do conteúdo contido na página número 13
Planning Information Built-In Model 650G HANDLE PROFILE – STAINLESS STEEL / OVERLAY APPLICATIONS STANDARD STAINLESS STEEL HANDLE 2" 3" 1" (51) (76) 1 1 /4" (32) PANEL 1" (25) PANEL 3 /4" (19) PANEL 5 /8" (16) PANEL 1 /2" (13) PANEL 1 /4" (6) PANEL 1 /4" (6) APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR DOOR NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK. PANEL AND HANDLE PROFILE The full-scale illustration above shows han
Resumo do conteúdo contido na página número 14
Planning Information Built-In Model 650G PANEL AND HANDLE PROFILE – 130˚ DOOR OPENING 130˚ DOOR OPENING SUB-ZERO UNIT WITH 2" (51) FILLER STRIP SUB-ZERO UNIT (TOP VIEW) FILLER STRIP 2" (51) ALLOW FOR FILLER LAP BEHIND FLANGE DOOR CLOSED OVERLAY PANEL MAIN FRAME 3/4" (19) THICK (NOMINAL) HINGE APPROX PROFILE OF STAINLESS STEEL DOOR STANDARD AND HANDLE FRAMED FULL-LENGTH HANDLE DOOR OPEN @ 130˚ OPTIONAL FRAMED EXTENDED FULL-LENGTH HANDLE The full-scale illustration above shows the panel To obt
Resumo do conteúdo contido na página número 15
Planning Information Built-In Model 650G OVERLAY PANEL APPLICATION – 90˚ DOOR OPENING 90˚ DOOR OPENING NOMINAL OVERALL WIDTH OF SUB-ZERO (TOP VIEW) SUB-ZERO UNIT 7 23 /8" (606) TO REAR OF SUB-ZERO MAIN FRAME 0" (0) 1 /4" (6) DOOR CLOSED 1 /2" (25) 3 /4" (19) HINGE 1" (25) 1 1 /4" (32) 1 1 /2" (38) 3 1 /4" (44) 2" (51) 1 2 /4" (57) 1 2 /2" (63) DOOR OPEN @ 90˚ 3 2 /4" (70) 3" (76) 1 3 /4" (83) 1 3 /2" (89) OVERLAY PANEL 3/4" (19) THICK (NOMINAL) *Approximate thickness of wrapped stainless steel
