Resumo do conteúdo contido na página número 1
HEAT CONTROLLER, INC.
Dehumidifier
MODELS: BHD-301-D
BHD-501-D
BHD-651-D
Service Manual
CAUTION
-Before servicing the unit, read the "safety precautions" in this manual.
-Only for authorized service personnel.
Resumo do conteúdo contido na página número 2
CONTENTS 1. PREFACE 1.1 SAFETY PRECAUTIONS...........................................................................................................................3 1.2 FEATURES AND DIMENSIONS ................................................................................................................3 1.2.1 FEATURES........................................................................................................................................3 1.2.2 DIMENSIONS ......................
Resumo do conteúdo contido na página número 3
1. PREFACE This Service Manual provides various service information, including the mechanical and electrical parts. This dehumidifier was manufactured and assembled under the strict quality control procedures. The refrigerant is charged at the factory. Be sure to read the safety precaution prior to servicing the unit. 1.1 SAFETY PRECAUTIONS • Disconnect the power supply before servicing or replacing any component. • Do not cut off the grounding prong or alter the plug in any manner. 1.2 FEATURES
Resumo do conteúdo contido na página número 4
1.3 SPECIFICATIONS MODELS BHD-301-D BHD-501-D BHD-651-D ITEMS CAPACITY(Pints/24hrs) 30 50 65 POWER SUPPLY(Phase,V,Hz) 1Ø, 115V,60Hz INPUT(W) 490 615 710 RUNNING CURRENT(A) 4.8 5.9 7.0 ENERGY FACTOR(L/kw.h) 1.2 1.6 1.80 REFRIGERANT R22 REFRIGERANT CHARGE, oz(g) 5.29(150) 7.23(205) 8.82(250) THERMISTOR OPEN 33.8 ˚F(1±0.5°C) CLOSE 50 ˚F(10±0.5°C) SOLENOID VALVE Using Temp/Humid.:-4~122 ˚F(-20~50°C)/95%RH Rating:7W/90mA COMPRESSOR MODEL No. SD063SW YZG-A17D2T2 QA114CBG PROTECTOR OVERLOAD PROTECTOR F
Resumo do conteúdo contido na página número 5
1.4 CONTROL TYPE 1.4.1 Mechanical type Humidity Control • When you first use the dehumidifier, turn the humidity control to 5 or 6. If you still have moisture, turn the 5 4 6 humidity control to a higher setting. 3 7 High MAX is the highest setting. 2 8 • When excess moisture and dampness odors are Auto Low 1 9 Shut-Off gone, adjust the control to a lower setting. Use the Off Max Fan Speed dehumidifier as long as excess moisture is present. Humidity Control Figure 2 Fan Speed Auto Shut-Off
Resumo do conteúdo contido na página número 6
1.5 HOW TO OPERATE DEHUMIDIFIER 1.5.1 HOW DOES THE DEHUMIDIFIER WORK? Motor Condenser Moist, humid air is drawn over a cold refrigerated Fan Evaporator dehumidifying coil. Moisture in the air condenses on this coil and drains into a bucket (or through the bucket into a Dry Humid Air Out hose and drain). Air In Dry, clean air is drawn over the condenser where it is actually heated several degrees and discharged out the rear grill into the room. (See Figure 4) Rear Grille ■It is normal for the sur
Resumo do conteúdo contido na página número 7
1.5.5 HUMIDITY CONTROLLER 5(42%) 42% R.H 1.5.5.1 Mechanical Type 40% 4(50%) 6(35%) The humidity control can be set anywhere between Off and Max for normal operation. 3(60%) 7(30%) If you need more dehumidification, turn the Humidity Control toward Max. If you need less dehumidification, turn the Humidity Control toward Off. 2(70%) 8(25%) The relative humidity range is from 20% to 80%. (See Figure 6) 9(20%) Turn the Humidity Control to Off to stop the unit manually. 1(80%) Off Max. DEAD DIAL Figu
Resumo do conteúdo contido na página número 8
2. CIRCUIT DIAGRAM • MODEL : BHD-301-D PART NO. Q'TY RE- DESCRIPTION NO. PER SET MARKS BHD-301-D 6411A20001Z POWER CORD ASSEMBLY 1 S 1 6600FX5001G 1 S 2 SWITCH, ROCKER 4681A20040Q 3 MOTOR ASSEMBLY 1 S 0CZZA20005J 4 CAPACITOR 1 S TBZ31986001 COMPRESSOR, SET 1 S 5 EAF35787201 OLP 1 S 6 6871A20289B 1 S 7 PWB(PCB) ASSEMBLY, DISPLAY 6877A30013R 8 SENSOR ASSEMBLY 1 S 6601A30006A 9 SWITCH ASSEMBLY, ROTARY 1 S 6600A30003C SWITCH ASSEMBLY, MICRO 1 S 10 EBR39204301 PWB(PCB) ASSEMBLY, MAIN 1 S 11 S: SERVIC
Resumo do conteúdo contido na página número 9
• MODEL : BHD-501-D/BHD-651-D WIRING DIAGRAM MAIN PCB CN-FAN BK(HI) RD(LOW) MOTOR OR(COM) GN/YL F YL WH C CN-AC1 WH(BL) (N) BR BUCKET C CN-AC2 CN-SEN S/W HUMIDITY GN/YL SENSOR H R RD POWER RY-COMP S COMP. SMPS 4 3 BL THERMISTOR C FUSE 250V T3.15A O.L.P BK(BR) (L) 3854A20 02 24 47Z PART NO. Q'TY RE- DESCRIPTION NO. PER SET MARKS BHD-501-D BHD-651-D 6411A20001Z 1 POWER CORD ASSEMBLY 1 S EAU32357504 2 MOTOR ASSEMBLY 1 S EAU32357501 1 S 0CZZA20005N 0CZZA20005J 3 CAPACITOR CAPACITOR
Resumo do conteúdo contido na página número 10
3. DISASSEMBLY INSTRUCTIONS 3.1 MECHANICAL PARTS 3.1.1 BUCKET AND AIR FILTER 1. Turn the Humidity Control off(Mechanical type) or press the power button off. (Electronic type) 2. Disconnect the power supply. 3. Remove the bucket. (See Figure 9) 4. Pull out the air filter. (See Figure 10) Figure 9 Figure 10 3.1.2 FRONT CASE AND REAR GRILLE 1. Remove 2 screws which fasten the front grille. 2. Pull the front grille forward and upward. (See Figure 11) 3. Remove 6 screws that secure the rear grille.
Resumo do conteúdo contido na página número 11
3.2 CONTROL PARTS 3.2.1 POWER CORD ASSEMBLY 1. After opening the control box, remove the screw that holds the ground wire. (See Figure 15) 2. Disconnect the remaining leads of the power cord from the PWB(PCB) ASSEMBLY, MAIN, then remove it from the control box. Figure 15 3.2.2 SENSOR ASSEMBLY 1. Disconnect the sensor assembly from the PWB(PCB) ASSEMBLY, MAIN. 2. Remove the screw which fastens the humidity sensor. (See Figure 16) 3. Remove the thermistor from the holder. (See Figure 16) 4. Disc
Resumo do conteúdo contido na página número 12
3.2.6 CONTROL PANEL 3.2.6.1 CONTROL PANEL - Mechanical Type (BHD-301-D) 1. Disconnect housing and all leads of the rocker switch, SWITCH ASSEMBLY, ROTARY and PWB(PCB) ASSEMBLY, DISPLAY from PWB(PCB) ASSEMBLY, MAIN (3.1.3) 2. Pull out the knob assembly. 3. Remove the nut which fastens the SWITCH ASSEMBLY, ROTARY. 4. Remove the knob of the rotary switch by pulling it upward. 5. Pull out the rocker switch by pushing the hooks on the both sides of rocker switch. 6. Pull out the PWB(PCB) ASSEMBLY, DI
Resumo do conteúdo contido na página número 13
3.2.7 FAN AND MOTOR 1. Turn the nut left and full out the Fan by hands carefully. 2. Remove 2 screws that fasten Heat Exchange. 3. Lift the H/E and open the H/E around 45 degree clockwise carefully. (See Figure 21) 4. Unfasten 3 screws that secure the Motor and earth wire. (See Figure 22) 5. Remove the Motor. Figure 21 Figure 22 3.2.8 SHROUD AND DRAIN PAN 1. Discharge the refrigerant by using a refrigerant Recovery System. 2. After purging the unit completely, unbrace the Discharge and the Sucti
Resumo do conteúdo contido na página número 14
3.3 REFRIGERATING CYCLE 3.3.1 CONDENSER, EVAPORATOR AND CAPILLARY TUBE 1. Remove the insulation on the Heater/Evaporator (H/E) assembly 2. Pierce the pinch-off tube to discharge the refrigerant, using a refrigerant recovery system. 3. After discharging the refrigerant completely, remove 2 screws between the housing assembly and the H/E. (See Figure 25) 4. Lift the H/E and open the H/E around 45 degree counterclockwise carefully. Figure 25 Figure 26 5. Unbraze each of interconnecting tubes of the
Resumo do conteúdo contido na página número 15
3.4 HOW TO REPLACE THE REFRIGERATION SYSTEM 1. When replacing a refrigeration component, be sure 7. Recharge as follows : to discharge the refrigerant system by using a 1) Refrigeration cycle systems are charged from the refrigerant recovery system. High-side. If the total charge cannot be put 2. After discharging the unit completely, remove the in the High-side, the balance will be put in the desired component, and unbraze the pinch-off suction line through the access valve which you tubes.
Resumo do conteúdo contido na página número 16
Equipment needed: Vacuum pump, charging cylinder, manifold gauge, brazing equipment. pinch-off tool capable of making a vapor-proof seal, leak detector, tubing cutter, hand tools to remove components, service valve. EVAPORATOR ASSEMBLY (LOW PRESSURE SIDE) CONDENSER ASSEMBLY (HIGH PRESSURE SIDE) COMPOUND GAUGE MANIFOLD GAUGE CAPILLARY TUBE SEE INSETS BELOW COMPRESSOR Figure 29 LOW HI EXTERNAL VACUUM PUMP CHARGING CYLINDER Figure 30B-Charging Figure 30A-Pulling Vacuum —16— A B A B B A C
Resumo do conteúdo contido na página número 17
4. TROUBLESHOOTING GUIDE CONDITION CAUSE REMEDY 1. Dehumidifier does not start. (Both No power Check power supply at outlet. compressor and fan motor do not Correct if none. operate.) Poor plug contact at outlet. Install plug properly or replace it. Bucket is full. If Auto Shut Off lights, empty the bucket and replace properly. Humidity control is at Off position Turn the humidity control switch toward Max. Wire disconnected or loose Connect wire. Refer to wiring diagram for terminal identifica
Resumo do conteúdo contido na página número 18
CONDITION CAUSE REMEDY 5. Noisy operating Fan If cracked, out of balance, or partially missing, replace it Loose foreign material inside the housing. Remove it. Tube hits frame. Adjust tubing routine carefully. Fan blade hits frame Check Motor Mount. If loose, tighten it. Internal compressor noise. Replace compressor. Loose set screws Tighten them. Worn bearings of Motor Assembly If knocking sounds continue when running or loose, replace the motor. If the motor hums or noise appears to be inter
Resumo do conteúdo contido na página número 19
5. Exploded View • MODEL:BHD-301-D W0CZZ-2 149980 349600 554030 354210 268711-2 359012 264110 249950 346811 435300 131400 165010 135312 266002 238310 149410 268711-1 436500 266003 352113 235512 35211A 152302 266010 552111 752140 330870 567502 130410 554160 144410 148391 550140 — — —19 —
Resumo do conteúdo contido na página número 20
• MODEL:BHD-501-D W0CZZ-2 149980 349600 554030 354210 W0CZZ 359012 268711-2 249950 346811 435300 264110 131400 165010 135312 238310 235512 268711-1 436500 352113 35211A 152302 266010 552111 752140 330870 567502 130410 554160 144410 148391 550140 — — —20—
