Resumo do conteúdo contido na página número 1
VOL
READ
6 WRITE
2
ON/ READ/
DISC WRITE
Recordable
CDR200t
SERIES
User Guide
Guide de I’utilisateur
Bedienungsanleitung
Resumo do conteúdo contido na página número 2
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Systems Technology, Inc. Address: 100 Century Center Court San Jose, California 95112 Telephone: (408) 467-2330 FAX: (408) 437-8791 Type of Equipment: CD Recorder Model Name: CDR200t CDR200t-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received
Resumo do conteúdo contido na página número 3
Laser Diode Properties CAUTION Material : GaAlAs Use of controls or adjustments or performance of Wavelength : 780-790 nm procedures other than those specified herein may Emission Duration : Continuous result in hazardous radiation exposure. Laser Output Power : Less than 44.6 μW* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 This compact disc player is classified as a CLASS 1 LASER product. CLASS 1 LA
Resumo do conteúdo contido na página número 4
WARNING ¢ WARNING ¢ • The temperature where CDR200t is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CDR200t cover to reduce the risk of electric shock. • Always remove the disc before transporting CDR200t. i
Resumo do conteúdo contido na página número 5
Important Precautions Important Precautions Please read the following precautions before attempting to operate CDR200t. • Before recording a disc, be sure to clean the disc and CDR tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unuseable disc. • Always record in a dust-free environment. If the disc must be removed from CDR200t before recording is finished, store the disc in a clean, dust-free environment. • CDR200t co
Resumo do conteúdo contido na página número 6
Table of Contents Table of Contents Introduction ............................................................................. 1 CDR200t Features ......................................................... 1 Orange Book Compatible Recording ............................ 2 Chapter 1 - System Configuration ..................................... 3 For an IBM-PC computer with DOS or Windows ........ 3 For a Macintosh computer............................................. 3 About Discs ...
Resumo do conteúdo contido na página número 7
Introduction Introduction Thank you for purchasing a Yamaha CDR200t drive. Please read this manual before using the drive in order to make the best use of the superior CDR200t functions. After reading, please retain this manual for future reference. CDR200t Features n 2xS Recording - 6xS Reading The CDR200t is a CD-ROM recorder capable of recording at double speed (2xS), or normal speed (1xS). It can read discs at up to 6xS. n Compatible with Seven Different Formats The
Resumo do conteúdo contido na página número 8
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than the CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not possible to
Resumo do conteúdo contido na página número 9
Chapter 1 - System Configuration Chapter 1 - System Configuration In order to use the CDR200t, you will require the following. For an IBM-PC computer with DOS or Windows The following operating environment is required: • An IBM/AT or compatible PC with a 486/33MHz or better CPU • A vacant slot in which to install a SCSI card or a pre-installed SCSI card • A vacant half-height bay • Windows 3.1 or later, or Windows 95 • Sufficient hard disk space Note: You will need about twice as mu
Resumo do conteúdo contido na página número 10
Chapter 1 - System Configuration About Discs CD-R Discs On the CDR200t, you can use conventional CD-R discs that conform to the Recordable Compact Disc Systems Part II (Orange Book). Yamaha recommends the following Yamaha CD-R discs: > CDM12Y63 (f 120mm, 63 minutes) > CDM12Y74 (f 120mm, 74 minutes) > CDM12Y74M (f 120mm, 74 minutes) > CDM12Y74T (f 120mm, 74 minutes) Read-only Discs You can use discs with the logo which conform to the Compact Disc Read Only Memory standard (CD-
Resumo do conteúdo contido na página número 11
Chapter 2 - Installing the Yamaha CDR200t Drive Chapter 2 - Installing the Yamaha CDR200t Drive CDR200t drive settings Before installing the CDR drive into your computer, you will need to set the following jumpers. You set these jumpers by inserting jumper connectors into the jumper switch located on the rear panel of the CDR drive switch. ' SCSI ID settings ' Parity setting ' Terminator setting ' Block size setting Important: Use long-nose pliers to remove or insert jumper
Resumo do conteúdo contido na página número 12
Chapter 2 - Installing the Yamaha CDR200t Drive ' SCSI ID settings The SCSI ID number is used so that the computer will recognize a connected SCSI device. You can assign 0 through 7 as the SCSI ID number. Usually, “7” is reserved for the SCSI card ID number, and “0” is reserved for the first SCSI device in the chain. Use a number between 1 and 6 for the CDR200t. Refer to the diagram below for more information on setting the SCSI ID number. The factory set ID number is “3”. Importa
Resumo do conteúdo contido na página número 13
Chapter 2 - Installing the Yamaha CDR200t Drive ' Parity setting Parity ON (with a jumper) — Parity Check will be performed. Normally, use this setting. Parity OFF (without a jumper) — Parity Check will not be performed. Parity ON Parity OFF ID SELECT ID SELECT PARITY PARITY TERMINATOR TERMINATOR BLOCK SIZE BLOCK SIZE 124 124 ' Terminator setting The terminator setting indicates whether or not this device is the last connected SCSI device. Terminator ON (with a jumper) — Use thi
Resumo do conteúdo contido na página número 14
Chapter 2 - Installing the Yamaha CDR200t Drive ' Block size setting Block size ON (with a jumper) — Block Size is set to 512Byte/sector. This function is valid only for workstations, such as those that run UNIX. Block size OFF (without a jumper) — Normally, use this setting. Block Size ON Block Size OFF ID SELECT ID SELECT PARITY PARITY TERMINATOR TERMINATOR BLOCK SIZE BLOCK SIZE 124 124 Cable Connection SCSI cable Connect a SCSI cable to the SCSI INTERFACE CONNECTOR on the rear
Resumo do conteúdo contido na página número 15
Chapter 2 - Installing the Yamaha CDR200t Drive Audio output cable Connect an audio output cable to the AUDIO OUT connector in the lower left corner of the rear panel. Make sure that the projection of the connector is facing upward. DC power cable Connect a DC power cable to the DC INPUT connector on the lower right corner of the rear panel. Make sure that the notch on the connector is facing upward. 9 ID SELECT PARITY SER. NO. AUDIO OUT DC INPUT TERMINATOR 124 BLOCK SIZE RGL 1 +5V
Resumo do conteúdo contido na página número 16
Chapter 3 - Operation Chapter 3 - Operation Front Panel 6 1 ON/ READ/ DISC WRITE READ Recordable VOL 6 WRITE 2 23 4 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotat- ing the control clockwise will increase the volume level. 4 ON/DISC LED This indicator ligh
Resumo do conteúdo contido na página número 17
Chapter 3 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. 11 READ/ ON/ READ DISC WRITE 6 WRITE VOL 2 Recordable
Resumo do conteúdo contido na página número 18
Chapter 3 - Operation Ejecting the Disc If the CDR200t is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the SCSI command prohibits the eject operation while the CDR200t is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) Press the eject button If the CDR200t is not powered on: Pressing the eject button will not eject the di
Resumo do conteúdo contido na página número 19
Troubleshooting Troubleshooting If CDR200t is not performing as expected, look up the symptoms in the following table, then see what to do. Symptoms What to Do The power to the CDR200t is off • Check the DC power cable connection. The power to the computer is off • Check to see if the SCSI card is correctly installed. The CDR200t is not recognized by • Check the SCSI cable connection. the computer. • Make sure that SCSI ID numbers are assigned exclusively. • Make sure that the last device in
Resumo do conteúdo contido na página número 20
Appendix Specifications Interface SCSI 2 Data Capacity 1.2m/sec: 666MB 1.4m/sec: 540MB Record/Read Speed 1xS (real-time), 2xS, 4xS (read), 6xS (read) Data Transfer Rate 6xS: 900KB/sec 4xS: 600KB/sec 2xS: 300KB/sec 1xS: 150KB/sec Burst Transfer Rate 4.2MB/sec (record asynchronous) 3.4MB/sec (read asynchronous) Buffer Size 1MB (250 sectors) Access Speed 250ms Installation Horizontal<– 15 degrees Disc Loading Disc tray Audio Out Frequency Response 20 - 20,000Hz (Line Out) (normal speed) Output Level
