Manual do usuário Sears N8MPN100F14B1

Manual para o dispositivo Sears N8MPN100F14B1

Dispositivo: Sears N8MPN100F14B1
Categoria: Forno
Fabricante: Sears
Tamanho: 4.02 MB
Data de adição: 11/16/2013
Número de páginas: 56
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Sears N8MPN100F14B1. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Sears N8MPN100F14B1.

Para sua conveniência

Se a consulta dos manuais Sears N8MPN100F14B1 diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Sears N8MPN100F14B1 no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Sears N8MPN100F14B1 em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Sears N8MPN100F14B1 Manual de instruções - Online PDF
Advertisement
« Page 1 of 56 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Sears N8MPN100F14B1, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Sears N8MPN100F14B1. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

N8MPN& N8MPL
80+Single Stage
*8MPN& *8MPL
* Denotes Brands (C, H, T)
Category I Furnace
See section 5 for Category [ definition.
SAFETY REQUIREMENTS
Recognize safety information. This is the safety-alert symbolZl._. When you see this symbol on the furnace and in instruction manuals be alert
to the potential for personal injury.
Understand the signal words DANGER, WARNING, or CA UTION. These words are used with the safety-alert symbol. DANGER identifies the
most serious hazards, those that will r

Resumo do conteúdo contido na página número 2

START-UP CHECK SHEET (Keep this page for future reference) Recommended, but not required, Dealer Name: Address: Business Card Here City, State(Province), Zip or Postal Code: Phone: Owner Name: Manual Gas Shut-Off Upstream YES_I NO_I Address: of Furnace/Drip- Leg? City, State(Province), Zip or Postal Code: YES_I NO_I Drip-Leg Upstream of Gas Valve? NO[_I Blower Speed Checked? YES _1 Model Number: YEs_I NO[31 All Electrical Connections Tight? Serial Number: Gas Valve turned ON? YES _1 NO[_I Natura

Resumo do conteúdo contido na página número 3

1. Safe Installation Requirements • This furnace is not to be used for temporary heating of buildings or structures under construction. See "2. Installation, Item 10'_ FIRE, EXPLOSION, AND ASPHIXIATION HAZARD • This furnace is NOT approved for installation in mo- Improper adjustment, alteration, service, bile homes, trailers or recreation vehicles. maintance or installation could cause death, • Seal around supply and return air ducts. personal injury, and/or property damage. • Install correct fi

Resumo do conteúdo contido na página número 4

Frozen Water Pipe Hazard Ifyourfurnace remains off for an extended time, the pipes in your home could freeze and burst, resulting in serious water damage. If the structure will be unattended during cold weather you should take these precautions. FROZEN AND BURST WATER PIPE HAZARD Turn off the water supply to the structure and drain the water Failure to protect against the risk of freezing could lines if possible and add an antifreeze for potable water to result in property damage. drain traps an

Resumo do conteúdo contido na página número 5

• The furnace, ductwork and filters are cleaned as neces- The air temperature rise is within the rated rise range on sary to remove drywall dust and construction debris from the furnace rating plate, and the firing rate has been setto all HVAC system components after construction is com- the rating plate value. pleted. The filters used to clean the circulating air during the • Verify proper furnace operating conditions including igni- construction process must be either changed or thor- tion, ga

Resumo do conteúdo contido na página número 6

Dimensions and Clearances (*8MPN/L Models) MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS FOR ALL UNITS REAR 0 TOP FRONT (combustion air openings 3" in furnace and structure) 5113 Required For Service *24" _E ALL SIDES Of SUPPLY PLENUM 1" "24"Min. SIDES 0 VENT LEFT SIDE Single-Wall Vent 6" -- 3314 Type B-1 Double Wall Vent 1" 5f__ _ _1 TOP OF FURNACE 1" --A_ -- B -- "30" clearancerecommendedfor furnaceremoval. Horizontalposition:Linecontactispermissibleonly betweenlines formed by intersectionsof to

Resumo do conteúdo contido na página número 7

iiiiiiiiiiiiiiiii_!!!!!!!!:!i:iil ¸;i ¸ii ¸ii ¸ii ¸ii ¸ii ¸ii ¸ii ¸ii ¸ii ¸ii ¸i ¸iiiiliiiiii;;;iiiiiiii;i;il;i;i;i;iiii_ilili;i;i;i;;i;i;il;i;iiiii ¸i;iiiii!!! The horizontal furnaces may be installed directly on combustible wood flooring or supports, however, it is recommended for further i!i!i!i!i!i!i!i!i!i!i! i i i i i ii i ! i ! i!! i!i!!i!iiii! iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i i i i i T p,ca, Up.ow ,nsta.at,on fire protection cement board or sheet metal is placed between

Resumo do conteúdo contido na página número 8

3. Newlabels forrightside-up application onoutside ofblower kinking of the pressure switch hose, trim the hose to remove ex- compartment door may bepurchased inakitfrom your distrib- cess length. utortocover upside-down labels. Note: When drilling new holes make sure metal shavings do not fall on or in components, as this can shorten the life of the furnace. Downflow Venting: Thecombustion venter MUST berotated to vent outtheside foralldownflow installations, (see Figure 5).Bot- tom venting isno

Resumo do conteúdo contido na página número 9

7. Tighten the three (3) or four (4) screws that secure the venter NOTE: Unused open vent hole must be covered. A Vent Cover is supplied with Vent Pipe Shield Kit NAHAOO2VC. A 55/16" diameter assembly to the collector box. Do tighten screws enough to compress venter gasket. Vent Cover is available separately from your distributor, or one can be fabricated with sheet metal for all side vent installations. 8. Replace power leads to venter motor and reconnect hose to pressure switch. 4. Combustion

Resumo do conteúdo contido na página número 10

Outside Air (This is ONLY a guide. SubJect to codes of country having jurisdiction.) ThisinstallationNOTapprovedinCanada Vent GasVent G Vent_j_.Gable , GableV_/) ba_ventilated Attic'_ I Top Above Insulation_ (1) I 1 €_:;;_l TM I/ SoffitVen, Soffit Vent I_ utletAir (1) Outlet/1_ II _. Air(1) Inlet F...... NG_ _,, _ r-_ Inlet Air (1) -- Air (2) Inlet Air (1) ........ Air (2) MinimumOne Inletand OneOutlet AirSupply is Required May be in andCombination Shown Inlet Air OpeningMust beWithin12"(300mm)o

Resumo do conteúdo contido na página número 11

The Standard Method may be used, if the space has no less vol- (ACH) and equal to or greater than 0.10 ACH. Infiltration rates ume than 50 cubic feet per 1,000 BTUH of the maximum input rat- greater than 0.60 ACH shall not be used. The minimum required ings for all gas appliances installed in the space. The standard volume of the space varies with the number of ACH and shall be method permits indoor air to be used for combustion and ventila- determined per Table 2 or Equations 1 and 2. Determine

Resumo do conteúdo contido na página número 12

Z223.1-2002/N FPA 54-2002; and/or Section 7andAppendix Cof theCSA B149.1-05, National Standard ofCanada, Natural Gas andPropane Installation Code; thelocal building codes; furnace CARBON MONOXIDE POISONING HAZARD andventmanufacturer's instructions. Failure to follow the steps outlined below for each NOTE: The following instructions comply with the ANSI appliance connected to the venting system being placed Z223.1/NFPA 54 National Fuel Gas Code and CSA B149.1 Natu- into operation, could result in

Resumo do conteúdo contido na página número 13

13.2 or a listed, metal lining system. (See Section 7 Masonry Combined Venting into a Masonry Chimney Chimney Venting of these instructions.) Listed, corrugated metallic chimney liner systems in masonry Venting into a masonry or concrete chimney is only permitted chimneys shall be sized by using NFGC tables per 13.1.7 for dedi- as outlined in the NFGC or NSCNGPIC venting tables. Follow cated venting and per 13.2.19 for common venting with the maxi- all safe venting requirements. mum capacity red

Resumo do conteúdo contido na página número 14

Other than Direct Vent Termination Clearance iiiiiiiiiiiiiiiiiiiiiiiiiiiii i i! ii ii ! i ! !i ! ii i i i i i i i i i i i AREA WHERE TERMINAL IS NOT PERMITED IVIVENTTERMINAL AIRSUPPLVINLET Item Clearance Descriptions Canadian Installation (1) U.S. Installation (2) A Clearance above grade, veranda, porch, deck, balcony, or 12" (30cm) # 12" (30 cm) anticipated snow level B Clearance to a window or door that may be opened 6" (15 cm) for appliances _< 10,000 BTUH (3kW), 12" (3

Resumo do conteúdo contido na página número 15

7. Masonry Chimney Venting Ira claytile-lined masonry chimney is being used and it is exposed Chimney Inspection to the outdoors below the roof line, relining might be required. All masonry chimney construction must conform to Standard Chimneys shall conform to the Standard for Chimneys, Fire- ANSI/NFPA 211-2003 and to any state or local codes applicable. places, Vents, and Solid Fuel Burning Appliances ANSI/NFPA The chimney must be in good condition and a complete chimney 211-2003 in the United

Resumo do conteúdo contido na página número 16

CHIMNEY INSPECTION CHART Foradditionalrequirementsrefer tothe NationalFuelGasCodeNFPA541ANSI Z223.1-2002andANSIINFPA211-2003Chimneys,Fireplaces, Vents,andSolidFuel Burnin9 Appliancesin the U.S.A. orto the CanadianInstallationCodeCSA B149.1-05 in Canada. Rebuild I Reline andtile debris? Removemortar 1_ .._ tile m.isalignment, Yes mg sections, _10 No adapter venting Not Suitable ins[ruc_lons Tor w /,%-\ opp,cotion / Oondonsoto ",,

Resumo do conteúdo contido na página número 17

If the inspection of a previously used tile-lined chimney: Exterior Masonry Chimney, a. Shows signs of vent gas condensation, the chimney should FAN+NAT Installations with be relined in accordance with local codes and the authority Type-B Double-Wall Vent Connectors having jurisdiction. The chimney should be relined with a © NFPA & AGA listed metal liner, Type-B vent, or a listed chimney adapter kit to reduce condensation. If a condensate drain is required Table A- by local code, refer to the NF

Resumo do conteúdo contido na página número 18

Vent dampers onanyappliance connected to the common vent can cause condensation and corrosion in the venting system. Do not use vent dampers on appliances common vented with this fur- nace. 8. Gas Supply and Piping Gas Piping Requirements NOTE: The gas supply line must be installed by a qualifted service CARBON MONOXIDE POISONING, FIRE AND technician in accordance with all building codes. EXPLOSION HAZARD. NOTE: In the state of Massachusetts. Failure to follow safety warnings exactly could a. Ga

Resumo do conteúdo contido na página número 19

5, Use ground joint unions and install a drip leg no less than 3" long to trap dirt and moisture before it can enter gas control Gas Valve with Elbows (N8MP) valve inside furnace. 6, Provide a 1/8" NPT plugged tapping for test gauge connection immediately up stream of gas supply connection to furnace. 7. Use two pipe wrenches when making connections to prevent furnace gas control valve from turning. NOTE: If local codes allow the use of a flexible gas appliance con- nector, always use a new list

Resumo do conteúdo contido na página número 20

2. Follow steps 2 through 4 Piping with Street Elbows. Typical Gas Piping ('aMP) FIRE OR EXPLOSION HAZARD. Failure to properly install metal gas connector could result in death, personal injury and/or property damage. A flexible corrugated metal gas connector must be properly installed, shall not extend through the side of the furnace, and shall not be used inside the furnace. Black iron pipe shall be installed at the furnace gas control valve and extend a minimum of 2" outside furnace. 25-25-02


Manuais similares
# Manual do usuário Categoria Baixar
1 Sears 8MPL075B12B1 Manual de instruções Forno 0
2 Sears 8MPL100F20B1 Manual de instruções Forno 0
3 Sears 8MPL075F16B1 Manual de instruções Forno 0
4 Sears 8MPL100J20B1 Manual de instruções Forno 0
5 Sears 8MPN075F16B1 Manual de instruções Forno 0
6 Sears 8MPN075B12B1 Manual de instruções Forno 0
7 Sears 8MPL125J20B1 Manual de instruções Forno 0
8 Sears 8MPN100F20B1 Manual de instruções Forno 0
9 Sears 8MPN100F14B1 Manual de instruções Forno 0
10 Sears 8MPN050B12B1 Manual de instruções Forno 0
11 Sears 8MPN100J20B1 Manual de instruções Forno 0
12 Sears 8MPN150J20B1 Manual de instruções Forno 0
13 Sears 8MPN125J20B1 Manual de instruções Forno 0
14 Sears 9MPD Manual de instruções Forno 0
15 Sears 9MPD075F12B1 Manual de instruções Forno 0
16 Adams Condensing Oil-Fired Manual de instruções Forno 2
17 AirComm Corporation 10016 Manual de instruções Forno 0
18 AirComm Corporation 7516 Manual de instruções Forno 0
19 AirComm Corporation 50 Manual de instruções Forno 0
20 Air King 9320 Manual de instruções Forno 2