Resumo do conteúdo contido na página número 1
Installation
Automatic
Washers
W001C
W001C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 38910R8
February 2007
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Replacement Parts.............................................................................. 3 Table of Installation........................................................................................... 5 Dimensions and Specifications............................................................. 5 Contents Before You Start................................................................................... 6 Tools ............................................................................
Resumo do conteúdo contido na página número 4
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910 2
Resumo do conteúdo contido na página número 5
Replacement Parts If replacement parts are required, contact the source from which you purchased your washer. 38910 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3
Resumo do conteúdo contido na página número 6
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910 4
Resumo do conteúdo contido na página número 7
Installation Dimensions and Specifications 71,1 cm (28 in.) 56,2 cm (22,13 in.) 10,2 mm 66 cm 65 cm (0,4 in.) (26 in.) (25,6 in.) TLW2075N * With leveling legs turned into base. 38910 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 *73,7 cm (29 in.) *109,2 cm (43 in.) *91,4 cm (36 in.) *134,6 cm (53 in.) *102,2 cm (40,25 in.)
Resumo do conteúdo contido na página número 8
Installation Electrical Before You Start Refer to serial plate for specific electrical Tools requirements. For more detailed information, refer to For most installations, the basic tools you will need section on Electrical Requirements. are: Water Washer needs two standard 19,05 mm (3/4 inch) water 2 3 supply faucets with a pressure between 138 and 1 827 kPa (20 to 120 pounds per square inch). For more detailed information, refer to section on Water Supply Requirements. 4 D074I D074I 1 W
Resumo do conteúdo contido na página número 9
Installation NOTE: Do not tilt washer to front or sides when Installing the Washer moving. NOTE: If the washer is delivered on a cold day The shipping brace and plug should be saved and must (below freezing), or is stored in an unheated room be reinstalled whenever washer is moved or or area during the cold months, do not attempt to transported to a new location. This will prevent operate it until the washer has had a chance to damage to washer components. warm up. NOTE: Refer to your Us
Resumo do conteúdo contido na página número 10
Installation Step 3: Connect Fill Hoses NOTE: Refer to section on Water Supply Requirements before connecting fill hoses. The appliance is to be connected to the water mains 1 using new hose-sets and old hose-sets should not be reused. 3 Turn on the water supply faucets and flush the lines for 2 approximately two minutes to remove any foreign materials that could clog the filter screens in the fill hoses, or the screens in the water mixing valve. 5 NOTE: When installing in a newly construc
Resumo do conteúdo contido na página número 11
Installation Step 4: Connect Drain Hose to Drain Standpipe Installation Receptacle Place the adapter into the standpipe. Remove the drain hose from its shipping position on Remove the beaded tie-down strap from accessories the rear of the washer by unhooking the hose from the bag and place around standpipe and drain hose, retainer clamp. approximately 30 cm (12 inches) down from the top of pipe and tighten strap to hold hose to standpipe. This Find the instructions, on the following pages,
Resumo do conteúdo contido na página número 12
Installation High Standpipe Installation Low Standpipe Installation Place the adapter into the standpipe. Remove the No. 562P3 Siphon Break Kit is required for this type beaded tie-down strap from accessories bag and place of installation. This kit is available (as optional around standpipe and drain hose, approximately 30 cm equipment at extra cost) through an authorized dealer (12 inches) down from the top of pipe and tighten strap or parts distributor. Installation instructions are to hol
Resumo do conteúdo contido na página número 13
Installation Sink Installation In the Wall Installation For this type of installation, use the beaded tie-down For installations of this type, the drain hose MUST be strap (supplied in accessories bag), or use a large wire secured to one of the inlet hoses using the beaded tie- tie (available from your local hardware store) and down strap from accessories bag. secure the drain hose to the cabinet top hinge. Refer to NOTE: End of drain hose must not be below height Figure 9. This will prevent
Resumo do conteúdo contido na página número 14
Installation Laundry Tub Installation Step 5: Position and Level the Washer For this type of installation, the drain hose MUST be Position washer so it has sufficient clearance for secured to the stationary tub to prevent hose from installation and servicing. dislodging during use. Use the beaded tie-down strap Place rubber feet on all four leveling legs. (supplied in accessories bag) to secure hose. Place washer in position on a clean, dry, and We recommend leaving the standpipe adapter on t
Resumo do conteúdo contido na página número 15
Installation Step 6: Plug In the Washer Step 8: Check Lid Switch Refer to section on Electrical Requirements, and plug Washer should stop spinning when lid is opened. the washer in. W376IE0C W504SE3B Figure 15 W504SE3B Step 9: Check Installation Figure 13 Refer to Installer Checklist on the back cover of this Step 7: Add Water to the Washer manual and make sure that washer is installed correctly. To prevent damage to pump, do not run washer before adding at least one quart water to the tub.
Resumo do conteúdo contido na página número 16
Installation Electrical Requirements WARNING (240 Volt, 50 Hertz with 3 Prong Earthing Plug) Improper connection of the equipment- earthing conductor can result in a risk of NOTE: The wiring diagram is located in the electric shock. Check with a qualified control hood. electrician or serviceman if you are in doubt as to whether the washer is properly earthed. WARNING W218 To reduce the risk of fire, electric shock or Do not modify the plug provided with the washer – if personal injury, a
Resumo do conteúdo contido na página número 17
Installation Water Temperature Water Supply Requirements Cold: WARNING Recommended cold water temperature is 10° to 24° Celsius (50° to 75° Fahrenheit). Under certain conditions, hydrogen gas may be produced in a hot water system that Hot: has not been used for two weeks or more. Recommended hot water temperature is 60° to HYDROGEN GAS IS EXPLOSIVE. If the hot 66° Celsius (140° to 150° Fahrenheit). water system has not been used for such a period and before using the washer, turn on Warm
Resumo do conteúdo contido na página número 18
Installation Water Pressure Pressure must be a minimum of 138 to a maximum of 827 kPa (20 to 120 pounds per square inch) static pressure measured at the faucet. NOTE: For water pressure over 827 kPa (120 pounds per square inch) we recommend the installation of a pressure limiting valve (Part Number PSL50DK). This item may be purchased by calling 1300 652 100. NOTE: Water pressure under 138 kPa (20 pounds per square inch) will cause an extended fill time in the washer. Risers Risers (or a
Resumo do conteúdo contido na página número 19
Information for Handy Reference Date Purchased Model Number Serial Number Store Name Store Address Phone Number Service Agency Service Agency Address Phone Number NOTE: Record the above information and keep your sales slip. Model and serial numbers are located on the nameplate. Customer Care Centre and Information: 1300 652 100 38910 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17
Resumo do conteúdo contido na página número 20
Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 38910 18
