Resumo do conteúdo contido na página número 1
Operation/Maintenance
Washer-Extractors
Cabinet Hardmount
Refer to Page 6 for Model Identification
CHM1772C
CHM1772C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F8208401R3
www.comlaundry.com February 2011
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Safety Information.............................................................................. 2 Table of Explanation of Safety Messages........................................................... 2 Important Safety Instructions ............................................................... 2 Contents Safety Decals ........................................................................................ 4 Operator Safety..........................................................................
Resumo do conteúdo contido na página número 4
Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING” WARNING and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These To reduce the risk of fire, electric shock, precautions are intended for the personal safety of the serious injury or death to persons when operator, user, servicer and those maintaining the using your washer, follow these basic machine. precautions: W0
Resumo do conteúdo contido na página número 5
Safety Information 9. Do not install or store the washer where it will be 20. If the supply cord is damaged, it must be replaced exposed to water and/or weather. by a special cord or assembly, available from the manufacturer or its service agent. 10. Do not tamper with the controls. 21. Be sure water connections have a shut-off valve 11. Do not repair or replace any part of the washer, or and that fill hose connections are tight. CLOSE attempt any servicing unless specifically the shut-off
Resumo do conteúdo contido na página número 6
Safety Information WARNING CAUTION This machine must be installed, adjusted, Be careful around the open door, and serviced by qualified electrical particularly when loading from a level maintenance personnel familiar with the below the door. Impact with door edges construction and operation of this type of can cause personal injury. SW025 machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment
Resumo do conteúdo contido na página número 7
Safety Information Do not bypass any safety devices in the machine. Operator Safety WARNING WARNING NEVER insert hands or objects into Operating the machine with severe out-of- basket until it has completely stopped. balance loads could result in personal Doing so could result in serious injury. injury and serious equipment damage. SW012 W728 To ensure the safety of machine operators, the following maintenance checks must be performed daily: 1. Prior to operating the machine, verify that al
Resumo do conteúdo contido na página número 8
Introduction Model Identification Information in this manual is applicable to these models: Model HCD020GD2 HCN020KCF HCU020KL2 SCN020JC2 SCN020WDV SCU020JLF HCD020JD2 HCN020KCV HCU020KY2 SCN020JCF SCN020WY2 SCU020JLV HCD020LD2 HCN020KD2 HCU020KYF SCN020JCV SCN020WYF SCU020JX2 HCL020GD2 HCN020KDV HCU020KYV SCN020JD2 SCN020WYV SCU020JXF HCL020GN2 HCN020KEF HCZ020GN2 SCN020JEF SCU020GC2 SCU020JXV HCL020HDF HCN020KEV HCZ020HN2 SCN020JXF SCU020GD2 SCU020JY2 HCL020HN2 HCN020KY2 SCL020GCZ SCN020JY2 SC
Resumo do conteúdo contido na página número 9
Introduction (Continued) Model HCD040LD2 HCN040KEV SCL040HN2 SCN040JD2 SCU040GC2 SCU040JYF HCL040GN2 HCN040KY2 SCL040HNF SCN040JE2 SCU040GD2 SCU040JYV HCL040HC2 HCN040KYF SCL040JC2 SCN040JEF SCU040GE2 SCU040KN2 HCL040HDF HCN040KYV SCL040JD2 SCN040JY2 SCU040GL2 SCU040KNF HCL040HE2 HCU040GC2 SCL040JDF SCN040JYF SCU040GN2 SCU040KNV HCL040HN2 HCU040GD2 SCL040JE2 SCN040JYV SCU040GX2 SCU040WEV HCN040GC2 HCU040GE2 SCL040JEF SCN040KN2 SCU040GY2 UCL040GN2 HCN040GD2 HCU040GL2 SCL040JX2 SCN040KNF SCU040HN2
Resumo do conteúdo contido na página número 10
Introduction (Continued) Model HCD080LDV HCN080KDV HCU080KCV SCN080JDF SCU080GXF SCU080KNV HCL080HNF HCN080KEV HCU080KYF SCN080JYF SCU080GYF UCL080GNF HCN080GCF HCN080KYF HCU080KYV SCN080JYV SCU080HNF UCL080HNF HCN080GDF HCN080KYV SCL080GNF SCN080KNV SCU080JCF UCL080KNV HCN080GEF HCU080GCF SCL080HNF SCN080LCV SCU080JCV UCN080GNF HCN080GNF HCU080GDF SCL080KNV SCN080LDV SCU080JDF UCN080HNF HCN080GXF HCU080GEF SCN080GCF SCN080LYV SCU080JDV UCN080KNV HCN080GYF HCU080GLF SCN080GDF SCN080WCV SCU080JEF
Resumo do conteúdo contido na página número 11
Introduction Nameplate Location Replacement Parts The nameplate is located at the rear of the machine and If literature or replacement parts are required, contact inside door. Always provide the machine’s serial the source from whom the machine was purchased or number and model number when ordering parts or contact Alliance Laundry Systems at (920) 748-3950 when seeking technical assistance. for the name and address of the nearest authorized parts distributor. Customer Service 1 For technica
Resumo do conteúdo contido na página número 12
Introduction Model Number Familiarization Guide Sample Model Number: *CN040GC2OU1D01 Product Family *C Agency Approval N Washer-Extractor Capacity (pounds dry weight of laundry) 040 Type of Control G Actuation (C = Coin drop) C Washer-Extractor Speed Capability (2 = 2 speed) 2 Electrical Characteristics O Panel Type U Design Series 1 Heat Feature (D = Direct Steam) D Option Identification (varies from machine to machine) 01 * Denotes Brand Model No Model No.. *CN040GC2OUID01 S Se er rial No ial
Resumo do conteúdo contido na página número 13
Operation 4. Close door and turn handle counter clockwise. Operating Instructions Refer to Figure 5. 1. Turn on main power source (circuit breaker). NOTE: For 125 capacity models through 1/31/11, 2. Turn handle clockwise to open. Refer to close door and turn handle clockwise. Figure 3. For 125 capacity models starting 2/1/11, close door NOTE: For 125 capacity models through 1/31/11, and turn handle counter clockwise. press the Unlock/Stop keypad, push the button on door handle and turn han
Resumo do conteúdo contido na página número 14
Operation 7. Add liquid and/or powder supplies to supply b. Bleach: dispenser. Refer to Figure 6. • Liquid - Compartment 3 a. Detergent: • Powder - Compartment 2 • Liquid - Compartment 1 (prewash) + c. Softener: Compartment 3 • Liquid - Compartment 4 • Powder - Compartment 1 (prewash) + Compartment 2 a. DETERGENT Powder Liquid CHM2227N CHM2228N b. BLEACH Liquid Powder CHM2230N CHM2229N c. SOFTENER CHM2231N Figure 6 8. For vended models only. Insert coin(s) or card make payment and select the
Resumo do conteúdo contido na página número 15
Maintenance 3. Check door interlock before starting operation: WARNING a. Attempt to start the machine with the door open. The machine should not start with the Sharp edges can cause personal injury. door open. Wear safety glasses and gloves, use proper tools and provide lighting when b. Close the door and start the machine. The handling sheet metal parts. machine should not start with the door W366R1 unlocked. c. Attempt to open the door while the cycle is in IMPORTANT: Replace all pan
Resumo do conteúdo contido na página número 16
Maintenance Weekly Monthly 1. Check the machine for leaks. NOTE: Disconnect power to the machine at its source before performing the monthly maintenance a. Start an unloaded cycle to fill the machine. procedures. b. Verify that door and door gasket do not leak. 1. Use the following procedures to determine if c. Verify that the drain valve is operating and V-belt(s) require replacement or adjustment. Call that the drain system is free from obstruction. a qualified service technician in eit
Resumo do conteúdo contido na página número 17
Maintenance c. For flat-pulley drive systems, verify allowable distance of belt from edge of pulley. Refer to Table 1 below. Flat-Pulley Alignment Allowable Model 1 Distance from Edge 20 .09 in. (2 mm) 2 30 .09 in. (2 mm) 40 .09 in. (2 mm) 60 .38 in. (10 mm) H039I Table 1 1 Deflection d. For F and variable-speed models only, 2 Span Length verify that V-belts are properly tensioned by applying a set force to the belts and measuring Figure 8 the deflection to determine the belt tension.
Resumo do conteúdo contido na página número 18
Maintenance 7. Use compressed air to clean lint from motor. 8. Clean interior of machine, both basket and shell, by wiping with a water-soaked sponge or cloth. 9. Use compressed air to clean all electrical components of moisture and dust. 10. Verify the insulation is intact on all external wires 1 and that all connections are secure. If bare wire is evident, call a service technician. 11. For F and variable-speed models only, clean 2 AC drive cooling fan blades monthly (more often if requi
Resumo do conteúdo contido na página número 19
Maintenance • Remove discoloration or heat tint from Care of Stainless Steel overheating by scouring with a powder or by • Remove dirt and grease with detergent and water. employing special chemical solutions. Thoroughly rinse and dry after washing. • Do not leave sterilizing solutions on stainless • Avoid contact with dissimilar metals to prevent steel equipment for prolonged periods of time. galvanic corrosion when salty or acidic solutions • When an external chemical supply is used, ar
