Resumo do conteúdo contido na página número 1
WS-7136U
Wireless 433 MHz
Temperature Station
Instruction Manual
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS Topic Page Inventory of Contents 3 Additional Equipment 4 Quick Setup 5-9 Detailed Setup Guide Battery Installation 10-12 Setting the Time Format 13 Setting the Temp. Format 13-14 Setting the Time 14-15 Features Minimum and Maximum 16-17 Temperatures Resetting Minimum and 17 Maximum Temperatures Adding additional remote 17-19 temperature sensors (optional) Viewing and operating multiple 20 remote temperature sensors Mounting 21-22 Troubleshooting 23-26 Ma
Resumo do conteúdo contido na página número 3
INVENTORY OF CONTENTS 1. The indoor Figure 1 temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket. (Figure 2) 3. Mounting hardware. 4. Instruction Manual and Warranty Card. Figure 2 3
Resumo do conteúdo contido na página número 4
ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA 1.5V batteries. (for the indoor temperature station) 3. 2 Fresh AA 1.5V batteries. (for the temperature sensor) 4
Resumo do conteúdo contido na página número 5
QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of all units for 10 minutes. 3. Place the batteries into the remote temperature sensor first, then into the indoor temperature station. (All remote temperature sensors must be started before the indoor weather stations) 4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES. 5
Resumo do conteúdo contido na página número 6
In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both the indoor temperature and the outdoor temperature after the 15 minutes please retry the set up as shown on page five. After both the indoor temperature and outdoor temperature are displayed for 15 minutes you can place your remote temperat
Resumo do conteúdo contido na página número 7
Notes on Outdoor Sensor Placement The remote temperature sensor should be placed in a dry, shaded area. Fog and mist will not harm your remote temp/humidity sensor but direct rain must be avoided. The remote temperature sensor has a range of 80 feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or window can have up to 30 feet of resistance and an interior wall can have up to 20 feet of resistance. Your distance plus resistance shou
Resumo do conteúdo contido na página número 8
To complete the set up of your indoor temperature station after the 15 minutes have passed, please follow the steps below. 1. Press and hold the “SET” button for 5 seconds. Note: A “12h” or “24h” will appear on the top line. (“12h” for AM/PM, “24h” for military time) a. To change between “12h” and “24h” press and release the “RESET/+” button. b. When you have your choice shown on the display press and release the “SET” button once. 2. Degree Fahrenheit will now show. a. To ch
Resumo do conteúdo contido na página número 9
and release the “SET” button once. 3. An hour will now be flashing. a. Press and release the “RESET/+” button until the correct hour is shown. Note: When in the 12h mode “PM” is displayed in the upper left corner of the display between noon and midnight. During the AM hours this area will be blank. b. When the correct hour is shown, press and release the “SET” button once. 4. A minute will now be flashing. a. Press and release the “RESET/+” button until the correct minutes a
Resumo do conteúdo contido na página número 10
DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR Battery Battery cover compartment 1. Remove the mounting bracket. 2. Remove battery cover. 3. Observing the correct polarity, install 2 AA batteries—make sure they do not spring free, or start-up problems may occur. 4. Replace cover. 10
Resumo do conteúdo contido na página número 11
B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons for 15 minutes. This may interfere with the signals, causing temperatures to register incorrectly. 1. Remove the battery Battery cover cover on the backside. To do this, push up and pull out. 2. Observing Battery Compartment the correct polarity, install 2 AAA batteries. 3. Replace battery cover. 4. Wait 15 minutes or until both the indoor and outdoor temperatures are sho
Resumo do conteúdo contido na página número 12
indoor temperature in the INDOOR LCD and outdoor temperature in the OUTDOOR LCD. II. PROGRAMMING SEQUENCE The programming sequence and default (factory) settings for the indoor temperature station is as follows: 1. Time Format (default 12h) 2. Temperature Format (default °F) 3. Time-Hour (default 12) 4. Time-Minute (default 00) Programming Note: The instructions are arrange so that you can program each feature independently. If you would like to program the indoor temperat
Resumo do conteúdo contido na página número 13
III. SETTING THE TIME FORMAT 1. Press and hold the “SET” button for 5 seconds. 2. “12:h” will begin to flash. 3. Press and release the “RESET/+” button to select your desired time format. 4. Press and release the “SET” button to advance to the temperature format setting or wait 15 seconds for the display to return to the normal mode. IV. SETTING THE TEMPERATURE FORMAT 1. Press and hold the “SET” button for 5 seconds. 2. “12:h” will begin to flash. 3. Press and release the “
Resumo do conteúdo contido na página número 14
5. Press and release the “RESET/+” button to select your desired temperature format. 6. Press and release the “SET” button to advance to the time setting or wait 15 seconds for the display to return to the normal mode. V. SETTING THE TIME 1. Press and hold the “SET” button for 5 seconds. 2. “12:h” will begin to flash. 3. Press and release the “SET” button twice. 4. The hour will begin to flash. 5. Press and release the “RESET/+” button to advance the hour to your desired hour
Resumo do conteúdo contido na página número 15
move to the minute setting. 7. The minutes will begin to flash. 8. Press and release the “RESET/+” button to set the minutes. 9. Press and release the “SET” button to advance to the time setting or wait 15 seconds for the display to return to the normal mode. Note: There is “PM” displayed to the left of the hour when between noon and midnight. During the AM hours this area will be blank. 15
Resumo do conteúdo contido na página número 16
FEATURES A. MINIMUM AND MAXIMUM TEMPERATURES 1. Press and release the “MIN/MAX” button, “MIN” appears above and to the right of each temperature and the recorded minimum temperatures are displayed along with the time of the recorded minimum outdoor temperature. 2. Press and release the “MIN/MAX” button to toggle to the maximum temperatures, “MAX” appears above and to the right of each 16
Resumo do conteúdo contido na página número 17
temperature and the recorded maximum temperatures are displayed along with the time of the recorded maximum outdoor temperature. Please note that the flashing time is the time of the recorded outdoor temperature minimum or maximum. B. RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES To reset both the minimum and maximum temperatures—press and hold the “MIN/MAX” button for 5 seconds. C. ADDING ADDITIONAL REMOTE TEMPERATURE SENSORS (OPTIONAL) The WS-7136U is able to receive si
Resumo do conteúdo contido na página número 18
additional remote sensor units with the WS-7136U. These extra sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly. A TX6U will monitor temperature only, a TX3U will monitor temperature and display the temperature on its LCD, the TX3UP will monitor the temperature via a probe for use in pools, spas, etc. Note: When setting up multiple units it is important to remove the batteries from all existing units in operation, then t
Resumo do conteúdo contido na página número 19
1. It is necessary to remove the batteries from all units currently in operation. 2. Remove the battery covers to all remote sensor units. 3. Place all remote sensor units in a numeric sequential order. 4. In sequential order, install batteries (follow the same battery installation procedures seen in section “I” of the Detailed Set-Up Guide) into the remote sensors. 5. Install batteries into the indoor temperature station. 6. Follow the Detailed Set-Up Guide for programming and ope
Resumo do conteúdo contido na página número 20
D. VIEWING AND OPERATING WITH MULTIPLE REMOTE SENSOR UNITS 1. To view the temperature of a different remote sensor unit, press and release the “CH” button. A shift from one “boxed” number to the next should be observed in the OUTDOOR LCD. 2. To view the Minimum/Maximum temperature: first select from which remote temperature sensor to read data from (indicated by the “boxed” number). Pressing and releasing the “MIN/MAX” button will toggle through the minimum and maximum indoor t
