Resumo do conteúdo contido na página número 1
2723303
Owner's Manual
ELECTRIC NAILER
Model No.
836.272330
Serial No.
NOTE: Model and serial numbers may be found on the name plate
located on the tool.
You should record both numbers and retain them in a safe place.
its Safety Rules and Operating instructions.
CAUTION: Before using this Nailer, read this manual and follow all
E185030
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Resumo do conteúdo contido na página número 2
SECTION PAGE Warranty ................................................... 2 Product Specifications ........................................ 2 Safety Instructions ........................................... 3 Accessories and Attachments .................................. 6 Know Your Brad Nailer ........................................ 7 Operation .................................................. 7 Maintenance ................................................ 8 Troubleshooting Guide ..............
Resumo do conteúdo contido na página número 3
6. DON'T FORCETHETOOL. It will do GENERAL SAFETY INSTRUCTIONS the job better and safer if used at the rate for which it was designed. USETHE RIGHTTOOL Do not use Do not attempt to operate this tool until 7. a tool for a purpose it was not you have read and thoroughly intended. For example, do not force understand all instructions, safety a small tool or attachment to do the rules, etc., contained in this manual. job of a heavy-duty tool. Failure to comply can result in accidents involving fire,
Resumo do conteúdo contido na página número 4
13. DISCONNECTTOOL when not in 17. REPLACEMENT PARTS, When use, before servicing and when servicing, use only identical loading or changing accessories. replacement parts ordered from a Sears service facility. 14.AVOID UNINTENTIONAL 18.WEAR HEARING PROTECTION STARTING. Never carry tool with your finger on the switch. during extended periods of operation. 15.STAY ALERT, Watch what you are GUIDELINES FOR doing and use common sense. Do EXTENSION CORDS not operate tool when you are tired or under th
Resumo do conteúdo contido na página número 5
SPECIFIC SAFETY INSTRUCTIONS 10.DURING OPERATION, the nailer FOR THIS NAILER may feel warm to the touch. This is normal. However, if the nailer starts to feel hot, discontinue use until the unit cools down, DO NOT AIM NAILER OR SHOOT NAILS AT A PERSON OR ANIMAL. GROUNDING INSTRUCTIONS Released nails can cause severe injuries. 1. USE ONLYTHE NAILS INDICATED IN THE EVENT OF A MALFUNCTION in this manual. Use of accessories OR BREAKDOWN, grounding provides that are not designed for this tool a path
Resumo do conteúdo contido na página número 6
Figure A Figure B Grounding Lug is Connected to a g Plug Known Ground Grounding Prong __ 2-Prong ake Sure This Properly Grounded Receptacle 3-Prong Outlet FIGURE (A) Shows a 3-wire electrical plug and outlet that has a grounding If you have any doubts as to whether conductor. If a properly grounded outlet the tool is properly grounded or if the is not available, an adapter (FIGURE B) grounding instructions are unclear, can be used to temporarily connect check with a qualified electrician or this
Resumo do conteúdo contido na página número 7
Housing cap -- Trigger switch cord Housing Latch t Safety lock pin Nail magazine g mouth HOW TO LOAD YOUR BRAD 5. Load nails into the magazine, nail NAILER (FIGURE 1) points facing down toward the bottom of the nailer. 1. Unplug nailer from power source. 6. When loading different lengths, do not load nail heads into the 2. Use only brad nails recommended; see brad nail chart. upper part of the slot. 3. Push up the latch (1) toward the Load se that the nail points are at magazine and slide out th
Resumo do conteúdo contido na página número 8
TO NAIL (FIGURE 2) Do not allow familiarity of your nailer to Always wear safety goggles or safety make you careless. Remember that a glasses with side shields when careless fraction of a second is sufficient operating your nailer. Failure to do so to inflict severe injury. could result in objects being thrown Fig. 2 into your eyes, resulting in possible serious injury. 1. Plug nailer into 120 Volt, 60Hz power outlet, 2. Hold nailer firmly with the tacking 4 mouth (1) flat to the workpiece. 3 3.
Resumo do conteúdo contido na página número 9
CLEARING A JAMMED NAIL 7. Replace all parts in reverse order. 8. Tighten screws. (FIGURE 3) 9. Make sure that the safety lock pin is correctly sticking out of the tacking 1. Unplug the cord and remove all mouth assembly. brads from the magazine. 2. Remove the two screws and Fig. 3 washers (1) located on the tacking mouth cover. 3. Remove the cover (2). CAUTION: Be careful, the safety lock pin and spring may shoot forward. 4. Remove safety lock pin (3) and spring (4). NOTE: Safety lock pin (3) ha
Resumo do conteúdo contido na página número 10
MODEL NUMBER 836,27233 ELECTRIC BRAD NAILER Order by PART NUMBER, not by key number Key Number Part Number Description 1 DCA0060030 Slot-cover (B) 2 DCAO050080 Slot-cover (A) 3 BMSO040010 Screw 4 DCA0790070 Safety cover 5 BMDO010000 Washer 6 DHBO040010 Housing screw 7 BMS0040361 Screw 8 BMS0040210 Screw 9 DHA0190010 Safety spring 10 DAA0320060 Safety lock pin (Guide bar) 1t 2723301 Screwdriver 12 2723302 Carry case 13 2723303 Owner's manual 14 2723304 Hex Key Page 10
Resumo do conteúdo contido na página número 11
13
Resumo do conteúdo contido na página número 12
Forthe repair or replacement parts you need delivered directly to your home Call 7 am - 7 pro, 7 days a week 1-800-366-PART (1-800-366-7278) Forin-home majorbrandrepairservice Call24 hoursa day,7 daysaweek 1-800-4-REPAIR (1-800-473-7247) Forthe locationof a SearsPartsand RepairCenterinyourarea Call24 hoursa day,7 daysa week 1-800-488-1222 A For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 pm, Monday-Saturday 1-800-827-6655 The mo
