Resumo do conteúdo contido na página número 1
MODEL G0702
12" DISC SANDER w/BRAKE
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Table of Contents INTRODUCTION ............................................................................................................................... 2 SECTION 1: SAFETY ....................................................................................................................... 5 SECTION 2: CIRCUIT REQUIREMENTS ........................................................................................ 8 SECTION 3: SETUP ........
Resumo do conteúdo contido na página número 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Resumo do conteúdo contido na página número 5
M Ma a a a a a a a a a a a a achin a a ac c c c c c c c c c c c c c c c c c c c c chi e Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0702 12" DISC SANDER WITH BRAKE Weight.............................................................................................................................................................. 103 lbs. Length/Width/Height..........................................................
Resumo do conteúdo contido na página número 6
Identification A. F. B. G. C. H. D. I. E. J.
Resumo do conteúdo contido na página número 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indicat
Resumo do conteúdo contido na página número 8
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROP- 16. REMOVE CHUCK KEYS OR ADJUSTING ERLY SUPERVISED PERSONNEL TO TOOLS. OPERATE MACHINERY. 17. DAMAGED MACHINERY. 8. KEEP CHILDREN/VISITORS AWAY. 18. DO NOT FORCE MACHINERY. 9. UNATTENDED OPERATION. 19. SECURE WORKPIECE. OFF 10. DO NOT USE IN DANGEROUS 20. DO NOT OVERREACH. ENVIRONMENTS.
Resumo do conteúdo contido na página número 9
Additional Safety Instructions for Sanders 6. PREVENTING FINGER INJURIES. 1. AVOIDING WORKPIECE GRAB. 7. AVOIDING ENTANGLEMENT. 2. AVOIDING KICKBACK. 8. DUST HAZARD. 3. SAFE SERVICING. 4. SAFE SANDING OPERATIONS. do not sand it. 9. WEAR RESPIRATOR. 5. AVOIDING ENTANGLEMENT. No l
Resumo do conteúdo contido na página número 10
SECTION 2: CIRCUIT REQUIREMENTS Power Connection Device 110V Operation Figure 1 Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not Figure 1. correctly grounded or connected to the power source. Get help if you do not know what you are doing. Full Load
Resumo do conteúdo contido na página número 11
SECTION 3: SETUP Unpacking This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with please imme- the controls and opera- diately call Customer Service at (570) 546-9663 tions before starting the for advice. machine! Otherwise, filing a freight claim can be difficult. Wear safety glasses dur- ing the entire setup pro- cess! Inventory This machine and its com- po
Resumo do conteúdo contido na página número 12
Cleanup Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machinery. Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area. NOTICE Avoid chlorine-based s
Resumo do conteúdo contido na página número 13
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for working clearances. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted location.
Resumo do conteúdo contido na página número 14
Mounting Figure 5 Figure 3 Figure 5. Figure 4 Figure 4.
Resumo do conteúdo contido na página número 15
6. OFF Test Run 7. Figure 6 Troubleshooting Page 19 Figure 6. 8. To test run the machine: 1. 2. 3. 4. 5. ON
Resumo do conteúdo contido na página número 16
SECTION 4: OPERATIONS Operation Overview To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning Operations any operations. To complete a sanding operation, the operator does the following: 1. Damage to your eyes and lungs could result from using this machine without proper pro- tective gear. Always wear safety glasses and 2. a respirator when operating this machine. 3.
Resumo do conteúdo contido na página número 17
6. Attaching Sandpaper 7. X & Y Miter Slots To attach sandpaper: To sand using the miter slot: 1. 1. 2. 3. one-half 2. 4. Figure 8 Figure 7 Figure 8. Note: For sanding curves or irregular shapes, remove the miter gauge from the disc table. Always keep th
Resumo do conteúdo contido na página número 18
Miter Sanding Angle Sanding Figure 10 To perform miter sanding operations: 1. 2. Note: The miter gauge can be used in either direction in the slot to achieve the proper rela- tion of the workpiece to the disc. 3. Figure 9 Figure 10. To perform angle sanding operations: 1. . 2. Figure 11 Figure 9. Figur
Resumo do conteúdo contido na página número 19
SECTION 5: ACCESSORIES ® PRO-STICK Abrasive Surface Cleaners Sanding Discs from ISO 9002 Factories MODEL and TYPE GRIT Size Model Figure 12. G0572—Bench Top Dual Fan Dust Filter Figure 14 1 G3119— 2 ⁄2" x 3" Duct Adapter 1 G3119— 2 ⁄2" x 4" Duct Adapter Figure 13. Figure 15.
Resumo do conteúdo contido na página número 20
SECTION 6: MAINTENANCE Lubrication Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. Unpainted Cast Iron Schedule Daily Check: Figure 16 ® G5562—SLIPIT 1 Qt. Gel ® G5563—SLIPIT 12 oz Spray ® G2871—Boeshield T-9 12 oz Spray ® G2870—Boeshield T-9 4 oz Spray ® H3788—G96 Gun Treatment 12 oz Spray Weekly Maintenance: ® H3789—G96 Gun Treat
