Resumo do conteúdo contido na página número 1
Cordless Driver Drill
Equipped with Electric Brake
MODEL 6201D
MODEL 6201DW
With Fast Charger
INSTRUCTION MANUAL
SPECIFICATIONS
Model 6201D
Capacities No load speed IRPM)
Dimensions Net
1L x W x H) weight
High Low
Steel Wood Wood screw Machine screw
10 mm 21 mm 6.1 mm x 55 mm - - 350 237 mm x 57 mm x 243 mm 1.7 kg
(318'7 1 113116") I l1/4" x 2-3/16") I 6mm '"4'' 1
1 I 19-318" x 2-114" x 9-9/16") I 13.7 lbsl
* Battery Cartridge 9100 Model DC9700 Fast Charger
Voltage Charging time
Resumo do conteúdo contido na página número 2
I M PO RTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence o
Resumo do conteúdo contido na página número 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t
Resumo do conteúdo contido na página número 4
I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 4
Resumo do conteúdo contido na página número 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and e
Resumo do conteúdo contido na página número 6
Installing or removing battery cartridge .Always switch off the tool before insertion or removal or the battery cartridge. 0 To remove the battery cartridge, pull out Battery cartridge the set plate on the tool and grasp both I sides of the cartridge while withdrawing it from the tool. 0 To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fu
Resumo do conteúdo contido na página número 7
Installing or removing driver bit or drill bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. To install the bit, push the sleeve up to- ward the "FREE" side and turn the sleeve I FREE side counterclockwise while holding the ring with your other hand as illustrated at right. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. Then pu
Resumo do conteúdo contido na página número 8
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. 7 CAUTION : Before inserting the -attery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch to the left for clockwise rota- tion
Resumo do conteúdo contido na página número 9
Adjusting fastening torque Pointer 1 Drill marking The fastenina toraue can be adiusted in six - stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the -8- marking. The clutch will slip at varying torque levels when the pointer is set at the numbers 1 to 5. The clutch is designed not to slip at the -8- marking. Befor
Resumo do conteúdo contido na página número 10
Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the *’- marking. Then proceed as follows. 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with acenter- punch and hammer at the point to be drilled plac
Resumo do conteúdo contido na página número 11
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11
Resumo do conteúdo contido na página número 12
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bit Fast charger Model DC9700 I Size 1 Part No. Part No. 1 131 03-2 Phillips - 1 I Slotted I # 5F I 78401 0-OA I L' ~ 1 #7F 1784011-0A 12V Fast charger Model DC9012 Part No. 11307
Resumo do conteúdo contido na página número 13
Feb.-25-'92 US CORDLESS DRIVER DRILL Model 6201D Note: The switch and other part configurations may differ from country to country. 13
Resumo do conteúdo contido na página número 14
Feb.--25-'92 US MODEL 6201D ,& DESCRIPTION IikM ,& DESCRIPTION MAC MACHINE ~ - !! 1 1 Housing Set IWith Item 601 33 1 Flat Washer 16 34 1 Spur Gear 15 2 1 Name Plate 3 1 Pan Head Screw M4x22 IWith Washer1 35 1 Spur Gear 15 36 1 Spur Gear 15 4 7 Tapping Screw BT4x20 5 1 Hand Strap 37 1 Internal Gear 48 1 set Plate 38 1 Flat Washer 10 6 39 1 DC Motor 9 6 V 7 1 Switch 8 1 Lever 40 1 Sponge 14-72 41 1 sponge 14-72 9 1 Switch Lever 1 Pan Head Screw M5x22 42 1 Plane Bearing 4 10
Resumo do conteúdo contido na página número 15
P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or ma
