Manual do usuário Shindaiwa 89303

Manual para o dispositivo Shindaiwa 89303

Dispositivo: Shindaiwa 89303
Categoria: Roçadora
Fabricante: Shindaiwa
Tamanho: 1.87 MB
Data de adição: 7/12/2013
Número de páginas: 72
Imprimir o manual

Baixar

Como usar?

Nosso objetivo é fornecer-lhe o mais rapidamente possível o acesso ao conteúdo contido no manual de instruções para Shindaiwa 89303. Usando a pré-visualização online, você pode visualizar rapidamente o índice e ir para a página onde você vai encontrar a solução para seu problema com Shindaiwa 89303.

Para sua conveniência

Se a consulta dos manuais Shindaiwa 89303 diretamente no site não for conveniente para você, você tem duas soluções possíveis:

  • Visualização em tela cheia - Para visualizar facilmente o manual do usuário (sem baixá-lo para seu computador), você pode usar o modo de tela cheia. Para começar a visualização do manual Shindaiwa 89303 no modo de tela cheia, use o botão Tela cheia.
  • Download para seu computador - você também pode baixar o manual Shindaiwa 89303 em seu computador e mantê-lo em suas coleções. No entanto, se você não quer perder espaço no seu dispositivo, você sempre pode baixá-lo no futuro a partir de ManualsBase.
Shindaiwa 89303 Manual de instruções - Online PDF
Advertisement
« Page 1 of 72 »
Advertisement
Versão para impressão

Muitas pessoas preferem ler os documentos não na tela, mas na versão impressa. A opção de imprimir o manual também foi fornecida, você pode usá-la clicando na hiperligação acima - Imprimir o manual. Você não precisa imprimir o manual inteiro Shindaiwa 89303, apenas as páginas selecionadas. Respeite o papel.

Resumos

Abaixo você encontrará previews do conteúdo contido nas páginas subseqüentes do manual para Shindaiwa 89303. Se você deseja visualizar rapidamente o conteúdo das páginas subseqüentes, você pode usá-los.

Resumos do conteúdo
Resumo do conteúdo contido na página número 1

English................1
Español.........SP_1
Françias........FR_1
SHINDAIWA OWNER’S/OPERATOR’S MANUAL
C2510/EVC
BRUSHCUTTER
WARNING!
Minimize the risk of injury to yourself and oth-
ers! Read this manual and familiarize yourself with
the contents. Always wear eye and hearing protection
when operating this unit.
Part Number 89303 Rev. 06/2009

Resumo do conteúdo contido na página número 2

Introduction IMPORTANT! The Shindaiwa C4 series of hand-held WARNING! The information contained in these instruc- power equipment is designed and built The engine exhaust from this tions describes units available at the time to deliver superior performance and reli- product contains chemicals known to of publication. ability without compromise to quality, the State of California to cause can- comfort, safety or durability. Shindaiwa cer, birth defects or other reproduc- Shindaiwa Inc. r

Resumo do conteúdo contido na página número 3

Safety Work Safely WARNING! WARNING! Trimmers and brushcutters operate at Never make unauthorized Never operate very high speeds and can do serious dam- attachment installations. power equipment of any kind age or injury if they are misused or abused. if you are tired or if you are under the Never allow a person without training or - instruction to operate this unit! Stay Alert tion or any other substance that could You must be physically and mentally fit to affect your ability or judgem

Resumo do conteúdo contido na página número 4

Safety (continued) The Properly Equipped Operator Wear hearing protection devices and a Always wear eye protection such as broad-brimmed hat or helmet. A helmet goggles or safety glasses to shield is required when using a blade-equipped against thrown objects. brushcutter to clear small trees. Always wear a harness when operating the unit . It adds comfort and helps ensure safety by limiting Prolonged exposure to excessive noise movement fore and aft. When the harness is is fatiguing an

Resumo do conteúdo contido na página número 5

Product Description Ignition Switch Using the illustration as a guide, Throttle Interlock familiarize yourself with your machine and its various compo- nents. Understanding your machine helps ensure top performance, long Hanger Throttle service life and safer operation. Trigger Fuel Tank Grip Outer Tube Handle Gearcase WARNING! Cutting Attachment Do not make unauthorized Shield these units or their components. Engine Name C2510 Engine Model SF2510E Engine Type 4-cycle, vertical cylinder

Resumo do conteúdo contido na página número 6

Assembly This unit comes fully assembled with the This unit comes fully assembled with the Engine and shaft assembly exception of the cutting attachment shield exception of the cutting attachment shield and cutting attachment. Cutting attachment shield and cutting attachment. IMPORTANT! Cutting attachment Prior to Assembly The terms “left”, “left-hand”, and “LH”; Before assembling, make sure you have all “right”, “right-hand”, and “RH”; “front” and Kit containing cutting attachment th

Resumo do conteúdo contido na página número 7

Assembly (continued) Cutting Attachment Shield - C unit 1. Insert the cutting attachment shield TX unit between the outer tube and the cutting attachment mounting plate. Outer Tube Socket-Head Bracket NOTE: Cap Screws It may be necessary to loosen the retain- ing nut and clamp screw to adjust cutting attachment shield mounting plate. Shim 2. Fit the two shims and the bracket over Clamp Screw the outer tube and loosely install the four socket-head screws. 3. Tighten the four socket-head cap

Resumo do conteúdo contido na página número 8

Assembly (continued) Adjust throttle lever free play The throttle lever free play should be approximately 4 - 6 mm (3/16” - 1/4”). Make sure that the throttle lever oper- ates smoothly without binding. If it becomes necessary to adjust the lever 4-6 mm free play, follow the procedures and illus- (3/16”-1/4”) trations that follow. Throttle Free Play 1. Loosen the air cleaner cover knob(s) and remove the air cleaner cover. Throttle Lever Free Play Remove air cleaner cover 2. Loosen the lock

Resumo do conteúdo contido na página número 9

Assembly (continued) Installing Brushcutter Blade Shaft Bolt WARNING! Do not attach any blade to a unit without proper installation of Bolt Guard all required parts. Failure to use the Holder B proper parts can cause the blade to Blade and/or bystanders. Gear Shaft 1. Turn the unit upside down so the gear Holder A case output shaft is facing UP and remove the shaft bolt, bolt guard and holder B from the gear case shaft. Output Shaft 2. Align the hole in blade holder A with the matching

Resumo do conteúdo contido na página número 10

Mixing fuel Mixing fuel Examples of 50:1 mixing quantities CAUTION! CAUTION! U.S. METRIC This engine is designed to operate on 2-cycle 2-cycle Never use any type of gasoline con- Gasoline Gasoline mixing oil mixing oil a 50:1 mixture consisting of unleaded taining more than 10% alcohol by vol- US Gallons Fl.oz. Liter cc. gasoline and ISO-L-EGD or JASO FD ume! Some types of gasoline contain 1 2.6 4 80 class 2-cycle mixing oil only. Use of alcohol as an oxygenate. Oxygenated 2 5.2 8 160 non-a

Resumo do conteúdo contido na página número 11

Starting the Engine IMPORTANT! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP. Ignition WARNING! Return Tube Throttle Lock Primer Bulb switch Button Never start the engine from the operating position. ON 1. Slide the ignition switch to the “ON” Throttle lever position. 2. Set the throttle lever to the “fast idle”: a. Squeeze the throttle lever toward the handgrip on the shaft tube. Press primer bulb.

Resumo do conteúdo contido na página número 12

Starting the Engine (continued) Starting A Flooded Engine 1. Disconnect the spark plug lead and use 3. Open the choke and fully depress the 5. Repeat the starting procedure for a the spark plug wrench to remove the throttle lever with your left hand, then warm engine. spark plug (turn counter clockwise to pull the starter handle rapidly with your 6. If the engine still fails to start, refer to remove). right hand to clear excess fuel from the the troubleshooting section near the combustion

Resumo do conteúdo contido na página número 13

Operation Shoulder strap IMPORTANT! WARNING! Adjust the shoulder strap so the shoul- Always wear a shoulder strap der pad rests comfortably on the off-side or harness when operating this unit. Shoulder strap shoulder and the cutting path of the cut- Using a harness with a brushcutter required for use ting attachment is parallel to the ground. with Brushcutters allows you to maintain proper control Make sure all hooks and adjustment of the unit and reduces fatigue during devices are sec

Resumo do conteúdo contido na página número 14

T U C T O N O D Operation (continued) Using a blade Whenever you strike a hard object Brushcutter Shoulder Strap WARNING! with a blade, always stop the A shoulder strap provides additional pro- brushcutter and carefully inspect the tection against blade thrust. In addition, a Before working with a blade-equipped blade for damage. NEVER OPER- shoulder strap gives significant support and unit, always inspect and clean the ATE THE BRUSHCUTTER WITH A comfort to help ensure safe and effici

Resumo do conteúdo contido na página número 15

Maintenance General maintenancel IMPORTANT! WARNING! WARNING! MAINTENANCE, REPLACEMENT Before performing any mainte- Non-standard accessories, cut- OR REPAIR OF EMISSION CONTROL nance, repair, or cleaning work on the ting attachment, or replacement parts DEVICES AND SYSTEMS MAY BE PER- unit, make sure the engine and cutting may not operate properly with your unit FORMED BY ANY REPAIR ESTABLISH- attachment are completely stopped. and may cause damage and lead to MENT OR INDIVIDUAL; HOWEVE

Resumo do conteúdo contido na página número 16

Maintenance (continued) 10-Hour maintenance (more frequently in dusty conditions) Loosen fasteners 1. Remove the air filter cover by loosen- ing the cover screw(s) and lifting. 2. Remove and inspect the pre-filter. If the pre-filter is torn or otherwise dam- aged, replace it with a new one. 3. Clean the pre-filter with soap and water. Let dry before reinstalling. 4. Inspect the air filter element. If the ele- Filter element ment is damaged or distorted, replace it with a new one. 5. Tap filter gen

Resumo do conteúdo contido na página número 17

Maintenance (continued) 50-hour maintenance Remove and replace the fuel filter element. Use a hooked wire to extract the fuel filter from inside the fuel tank. Inspect the fuel filter element. If it shows signs of contam- ination, replace with a genuine Shindaiwa replacement fuel filter element. CAUTION! Make sure you do not pierce the fuel line Hooked wire with the end of the hooked wire. The line is delicate and can be damaged easily. Before reinstalling the new filter element, inspect the

Resumo do conteúdo contido na página número 18

Maintenance (continued) If the engine becomes sluggish and low on power, check and clean the spark arrester screen. Engine Cover WARNING! Engine Cover Never operate the unit with a Screws arrester! Operating with a missing or and could also damage your hearing. 1. With a 3 mm hex wrench remove the engine cover screws and the engine cover. 2. With a 4 mm hex wrench, remove the 3 muffler bolts and the muffler. 3. With a small flat bladed screwdriver remove the 2 screws holding the

Resumo do conteúdo contido na página número 19

Maintenance (continued) Blade Sharpening WARNING! Shindaiwa Tornado™ Blade Multiple-tooth Circular Blade Wear protective gloves when handling or performing maintenance Round on the blade. File When the cutting edges of the blade become dull, they can be resharpened with a few strokes of a file. Round File In order to keep the blade in balance, all cutting edges must be sharpened equally. Maintain a radius of 0.04 to 1 to 1.5 mm (0.06”) WARNING! The top plate of each at the base of each too

Resumo do conteúdo contido na página número 20

Troubleshooting Guide ENGINE DOES NOT START What To Check Possible Cause Remedy Faulty recoil starter. Consult with an authorized servicing dealer. NO Fluid in the crankcase. Does the engine crank? Internal damage. YES Loose spark plug. Tighten and re-test. NO Good compression? Excess wear on cylinder, piston, Consult with an authorized servicing rings. dealer. YES Fuel incorrect, stale, or contaminated; Refill with fresh, clean unleaded gasoline mixture incorrect. with a pump octane of 87 or


Manuais similares
# Manual do usuário Categoria Baixar
1 Shindaiwa 89302 Manual de instruções Roçadora 3
2 Shindaiwa 89304 Manual de instruções Roçadora 1
3 Shindaiwa C242/EVC Manual de instruções Roçadora 15
4 Shindaiwa 81359 Manual de instruções Roçadora 0
5 Shindaiwa BRUSHCUTTER C3410 Manual de instruções Roçadora 23
6 Shindaiwa 81644 Manual de instruções Roçadora 0
7 Shindaiwa C2510 Manual de instruções Roçadora 52
8 Shindaiwa 81714 Manual de instruções Roçadora 0
9 Shindaiwa C2510/EVC Manual de instruções Roçadora 11
10 Shindaiwa 81704 Manual de instruções Roçadora 0
11 Shindaiwa C282 Manual de instruções Roçadora 3
12 Shindaiwa C254 Manual de instruções Roçadora 4
13 Shindaiwa C3410/EVC Manual de instruções Roçadora 99
14 Shindaiwa C344 Manual de instruções Roçadora 24
15 Shindaiwa X7502825300 Manual de instruções Roçadora 0
16 Alamo SR14 Manual de instruções Roçadora 1
17 Alamo SR20 Manual de instruções Roçadora 2
18 Alamo GR60 Manual de instruções Roçadora 2
19 Alamo GR72 Manual de instruções Roçadora 1
20 Alamo TW84 Manual de instruções Roçadora 2