Resumo do conteúdo contido na página número 1
MINI VER MINI VERTICAL MILLING/ TICAL MILLING/
MINI VER MINI VER MINI VERTICAL MILLING/ TICAL MILLING/ TICAL MILLING/
DRILLING MACHINE DRILLING MACHINE DRILLING MACHINE
DRILLING MACHINE DRILLING MACHINE
44991
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2000 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape o
Resumo do conteúdo contido na página número 2
Specifications ITEM DESCRIPTION Power Consumption 120 VAC, 60 Hz, single phase Motor 4/5 HP Speed Ranges 0 ~ 1100 low RPM and 0 ~ 2500 high RPM Spindle R-8 Taper Chuck JT33 Taper; 7/64 to 1/2 inch capacity End Mill Capacity 1/2 inch Face Mill Capacity 1 inch Drill Capacity 1/2 inch Micro Feed Scale 0.002 inch per line Depth Scale 0 to 12 inches in 1/16 inch increments Table Slot Width 1/2 inch Table Size 15-7/8 (L) x 3-11/16 (W) inches Unit Height 33-11/16 inches Weight 115 lbs. Save This Manual
Resumo do conteúdo contido na página número 3
6. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restri
Resumo do conteúdo contido na página número 4
of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. This tool requires use of an extension cord of 0 to 10 amps capability (up to 50 feet), with wire size rated at 18 AWG. Longer extension cords require larger size wire. If you are using the tool outdoors, use an extension cord rated for outdoor use. (signified by “WA” on the jacket). 21. Maintenance. For your s
Resumo do conteúdo contido na página número 5
3. An optional oil pan can be placed under the machine before it is mounted to the table. 4. Before operation, loosen the slide, worktable, and drill-mill spindle. They were locked for shipping. 5. Remove all packing material and clean machine with nonflammable solvent. Oil the machine according to the lubrication requirements before running the machine. Assembly 1. Install the Chuck. - Thoroughly clean the tapered hole in the Chuck (164) and the Spindle (79) shaft of all dirt, grease, oil, an
Resumo do conteúdo contido na página número 6
Checks before Operation 1. Turn on the machine by lifting the cover and pulling out the Emergency Stop Switch (137). 2. Turn the Speed Control Knob (134) and verify spindle speed changes. 3. Verify that the spindle is rotating clockwise. 4. Operate the Longitudinal Axis (Working Table), Cross Axis (Saddle Seat), and Vertical Axis (Vertical Support), and verify their proper operation and movement. Caution: Avoid injury to you or damage to machine. Unplug the power cord from the electrical outlet
Resumo do conteúdo contido na página número 7
2. Adjust the position of the Limit Block (65) up or down. Refer to the Ruler (67) on the side of the Vertical Support (68). 3. Tighten the Handle. Adjusting the Vertical Support Angle (68) 1. Using the Large Wrench (accessory A), loosen Lock Nut (70) only enough to allow movement of the Vertical Support (68). (70) Caution: Avoid injury or damaging machine, hold the Vertical Support in place to keep it from fall- ing to the left or right during adjustment. 2. Adjust the Vertical Support angle as
Resumo do conteúdo contido na página número 8
10. When the drilling or milling is completed, press in on the Emergency Stop Switch and close its cover. 11. Unplug the line cord from the electrical outlet and clean the machine of all debris. Maintenance Caution: Avoid injuries or damage to equipment. Before performing any maintenance on this machine, unplug the power cord from the electrical outlet. Lubrication Requirements 1. Using a light oil and clean cloth, after each use, wipe down all metal parts of the machine to prevent rusting. 2. U
Resumo do conteúdo contido na página número 9
Parts List 4 NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 44991 Page 9 REV 03/05
Resumo do conteúdo contido na página número 10
with REV 11/02 SKU 44991 Page 10
Resumo do conteúdo contido na página número 11
Longitudinal (Y) Axis and Cross (X) Axis Assembly Drawing SKU 44991 Page 11
Resumo do conteúdo contido na página número 12
Vertical (Z) Axis Assembly Drawing SKU 44991 Page 12
Resumo do conteúdo contido na página número 13
Spindle and Gear Box Assembly Drawing SKU 44991 Page 13
