Resumo do conteúdo contido na página número 1
TeamStation™ System 4.0 and 4.0a
Installation & Use
System 4.0 Restore Procedure
Use the restore procedure to configure the Intel® TeamStation™ System to its
factory-installed configuration.
WARNING! This procedure will erase all of the files on the disk, including the Intel
TeamStation System directory of numbers, any documents stored on the system
with the Intel TeamStation Document Server, and any applications and their data.
You will need to copy files and data that you want t
Resumo do conteúdo contido na página número 2
System 4.0a Restore Procedure In the event of a problem that makes the hard drive of the Intel® TeamStation™ System 4.0a unusable, the system administrator can reload the base Intel TeamStation System software. This process takes approximately 45 minutes. For the restore process, you will need: • Intel TeamStation System Restore Diskette • Intel TeamStation System Restore CD • Microsoft Windows* NT* Workstation 4.0 CD • Windows NT Certificate of Authenticity (located on the cover of
Resumo do conteúdo contido na página número 3
15. Install Update 1 to complete the Restore process. Run the update file found on the Intel TeamStation System Update 1 CD, as instructed in the Intel TeamStation System Version 4.0a, Update 1 Installation document. o North American English: TS40AU1NA.EXE o United Kingdom: TS40AU1EU.EXE o French: TS40AU1FR.EXE o German: TS40AU1GR.EXE o Italian: TS40AU1IT.EXE 16. Reboot the system. Note: If you use a television set as your display, follow instructions in the Version 4.0a README fi
Resumo do conteúdo contido na página número 4
8. Highlight ‘TCP/IP Protocol’ and click ‘OK’. 9. If a DHCP (Dynamic Host Control Protocol) server is available and DHCP will be used click ‘Yes’ at the prompt. If a static IP address will be used click ‘No’ at the prompt. 10. Insert the Microsoft Windows NT 4.0 CD. 11. When setup will prompts for the location of files enter ‘D:\I386\’ and click ‘Continue’. 12. Setup will prompt to configure RAS (Remote Access Services) for TCP/IP (check the Microsoft web site at http://www.microsoft.c
Resumo do conteúdo contido na página número 5
18. Click ‘Yes’ to reboot the system. 19. Click ‘OK’ at the ‘Invalid Display Settings’ error message. 20. Select the ‘Desktop Area’ to 800x600 and ‘Color Palette’ to 65536 Colors in the ‘Display Properties’. 21. Click ‘Test’ in ‘Display Properties’ to confirm the settings. 22. Click ‘OK’ in ‘Display Properties’ when the test is completed. • Tips and Tricks for Voicecrafter* 3000 Training 1. Make Sure the mic is at least 10 feet from the monitor (speakers) 2. Make sure the filter o
Resumo do conteúdo contido na página número 6
b. Press F2. The Display will show: AUTOADAPTION GAIN ADJUST DISABLED 8. Set the Mic Default Gain a. Click on "default" in the first row of buttons, under mic 1. The display should read: MIC 1 DEFAULT GAIN +03dB b. Press F2 to change this to -1dB. 9. Train the Voicecrafter a. Press on the Train Button. The display will show: TRAIN: F2 - REFRESH TRAIN F3 - CONFIG TRAIN b. Press F3. Be VERY SILENT! The Voicecrafter will be training. c. When the training is complete, you wil
Resumo do conteúdo contido na página número 7
• Reset 29 inch NEC Multisync to factory default settings The Intel® TeamStation™ System ships with an optional Monitor. Use the following instructions to reset the NEC MultiSync* 29 inch monitors to factory defaults. Default Settings for the NEC MultiSync* XV29: Press the "Recall" key on the remote control and use the following information to verify the settings. Volume 112 Mute off Woofer on (****should be off****) Brightness 128 Contrast 195 V-size 156 V-position 78 H-size 210
Resumo do conteúdo contido na página número 8
MultiFrame Alignment (First, Second, Third and fourth rows turn Green) (Aligning communications) If CRC errors continue to occur, the Fourth row will turn red (Rows 1, 2, and 3 will all be green) This indicates a problem on the ISDN line. If there are transmit errors (the system receives notification from the remote side that it received an error in the transmission), the third row will light up with blue. It is possible to have both CRC errors and transmit errors at t
Resumo do conteúdo contido na página número 9
One column has 4 green lights, but the second column has a steady blue and red on the third and fourth row: The second channel is experiencing a high rate of errors. Common causes include: • The connection is going over a 56K trunk. To specify using 56K channels instead of 64K channels, append a # sign at the end of the first number. Example: 15552251111# 15552251112 • The ISDN line has a problem. Contact the ISDN service provider to test the ISDN line. First channel shows 2 light
Resumo do conteúdo contido na página número 10
Data sharing on MCUs Lucent MCU 4.4 and Video Server 5.3 experience data-sharing difficulties. Microsoft Office 97* application are not properly shared to all participants and may not be visible at all endpoints. The Whiteboard tool may experience similar problems. This may also be noticed if an endpoint leaves the conference and then reenters. • LAN/WAN Network or TCP/IP Setup and Connection Information Installing TCP/IP or TCP/IP Connection Type is disabled Installation of TCP/IP on
