Resumo do conteúdo contido na página número 1
USER’S MANUAL
version 1.0
AT Factor / Wide SCSI
for
TX2
Dual CPUs ATX Factor
for
ATX586
MAIN BOARD
Intelligent
Intel 430TX PCI Chipset
Resumo do conteúdo contido na página número 2
UPDATE INFORAMTION JULY 22, 97 1) When you install ATX power supply, please connect CASE STANDBY to front panel connector CN9/JP9 , pin 19-20 Power On. Then 2) The difference between TX2 and TX3 is that TX3 is without SCSI port/chip. Others 2 are the same. turn on ATX power supply.
Resumo do conteúdo contido na página número 3
Preface .................................................................. 1 CHAPTER 1 Hardware Installation for 4 ATX586 1.1 One Jumper to Set CPU..................... … 4 1.2 Two Jumper to Set CPU......... … … … … … 6 1.3 Other Hardware 7 Jumpers......................... 1.4 Install System DRAM 8 Memory............... 1.5 Install IDE, I/O and Front 10 Panel........ … … . 1.6 I/O Address And 12 IRQ................................ 1.7 Jumpers 12 List................
Resumo do conteúdo contido na página número 4
2.6 PNP/PCI 18 Configuration............................. 2.7 Integrated 18 Peripherals.............................. 2.8 AWARD BIOS Post 19 Code......................... CHAPTER 3 EIDE & FLASH BIOS 24 Part I. Installation Ultra EIDE 24 Driver............... Part II. Update Flash 48 BIOS............................. 4 SETUP......
Resumo do conteúdo contido na página número 5
Hardware Installation for TX2 49 4.1 One Jumper to Set CPU..................... … 50 4.2 Two Jumper to Set CPU......... … … … … … 52 4.3 Other Hardware 53 Jumpers......................... 4.4 Install System DRAM 54 Memory............... 4.5 Install IDE, I/O and Front 56 Panel........ … … . 4.6 I/O Address And 58 IRQ................................ 4.7 Jumpers 58 List............................................. 4.8 Pin Definition for Cable 59 Connection........
Resumo do conteúdo contido na página número 6
Inside the Document ATX586 Dual Pentium Main Board with Intel , resulting in Ultra IDE performance. ATX586 is for ATX platform with dual processors design, including Enhance I/O chip (SMC 669 compatible). There is an option that installing “ 82093AA” supports two Intel Pentium (MMX) CPU, said Dual Processors. Under single processor, the user installs Intel + . Excepting above mentioned, ATX586 is designed with Auto Switching between 3.3v and 2.8v CPU (when you use single CPU only), front panel
Resumo do conteúdo contido na página número 7
(Chapter 4 about is positions, jumpers and connectors for TX2. Due to the board supports full range of Pentium CPU MMX 75Mhz- + .) Simple features: ² Intel 430 TX PCISET . 82439TX System Controller (MTXC), 82371AB PIIX4 PCI to ISA / IDE Xcelerator, 82093AA I/O Advanced Programmable Interrupt Controller (IOAPIC). ² . ² Supports full range of Pentium Processor Family, up to Intel +. Pentium MMX-233Mhz, AMD K6-PR-233, CX 6x86 200 There is an auto- switching mode from 3.3v to 2.8v. ² Installing
Resumo do conteúdo contido na página número 8
² 24 Programmable Interrupts: 13 ISA supported; 4 PCI; 1 interrupt/ SMI# rerouting; 2 motherboard ; 1 interrupt used for INTR input; 3 general purpose; independently programmable for edge/level sensitivity interrupts; each interrupt can be programmed to inputs. ² 4 * 32-bit PCI, 4 * 16 bit ISA Slots for ATX586 ² 2 * Ultra EIDE, support 4 IDE devices. EPP/ECP/SPP printer port. 2 * 16550 UART serial ports. PS/2 mouse port. IR, infrared, port, option for FIR, fast infrared. ² IDE controller: I
Resumo do conteúdo contido na página número 9
Chapter 1 Installation For ATX586 1.1 One Jumper to Set CPU , Simple Jumper No more CPU jumper setting when Single Processor Intel 133Mhz, +, CYRIX 166 AMD K5-133 CPU . (At the moment , JP6: 1- ) Intel ) 1-2 SHORT 2-3 SHORT 2-3 SHORT 1-2 SHORT 1-2 SHORT AMD ) 1-2 SHORT 2-3 SHORT 2-3 SHORT 1-2 SHORT 1-2 SHORT CYRIX ) + 2-3 SHORT 2-3 SHORT + 2-3 SHORT + 2-3 SHORT When you want to install two CPU, they are perfect are the same voltage 2.8v (P55C) or 3.3v(P54C). Different voltage can’t be st
Resumo do conteúdo contido na página número 10
Map of ATX586 Mother Board Default Setting for Intel Pentium 133Mhz, + AMD K5-133,CYRIX P166 ,512K PB Cache 1.2 Two-Jumper Setting for CPU 10
Resumo do conteúdo contido na página número 11
JP6/JP7 : Set CPU External Bus Frequency Rate (BF1, BF0) JP6/JP7: 1-2 , SHORT for Intel 90/100Mhz, MMX 233Mhz, AMD K5 75-133, JP6: 1-2 and JP7: 2-3 SHORT for Intel 120/ + 133 Mhz, CYRIX 120 - + (Default) JP6/JP7: 2-3 SHORT for Intel MMX150/166Mhz, SHORT and SHORT for Intel MMX 180/ 200Mhz,and AMD (JP6 means BF1 and JP7 means BF0. When 2-3 short means ACTIVE, 1-2 short means NON-ACTIVE) 11 K6 PR200. 1-2 JP7: JP6: 2-3 AMD K6 PR166Mhz 200 AMD K6 PR233Mhz
Resumo do conteúdo contido na página número 12
JP8/9: Set CPU External Bus Frequency Selection (FS0, FS1, FS2) JP8: 1-2 and JP9: 2-3 SHORT : 75Mhz for CX + JP8/9:1-2 SHORT: + Mhz for CX 166 , AMD K6, MMX. Intel/AMD 100/133/ 166/ 200 / JP8: 2-3 and JP9: 1-2 SHORT : 60Mhz for CX +, Intel/AMD 90/120/150 /180Mhz + SHORT 1.3 Other Hardware Jumpers J1 : Set the CPU Type: when you install two CPUs please use J1 to indicate the Voltage of CPU. If you only install one CPU, skip this à OPEN for P55C(Intel MMX, AMD K6, Default. 2.8v à 1-2, 3-4,
Resumo do conteúdo contido na página número 13
JP15: 2MB FLASH BIOS ONLY 2-3 SHORT for normal (set by factory). Default. 1-2 SHORT reserved for factory set only. JP16: Select FLASH BIOS 2-3 SHORT for 5v Flash BIOS, normal, Default.. 1-2 SHORT for 12v Flash BIOS (set by factory), JP18: JP13: CMOS. When you forget the password, clear CMOS, restart! 2-3 SHORT for normal. Default. 3-4 SHORT to clear CMOS (power must be off). OPEN for external battery installed. It is an important jumper. When BIOS setting is changed by user becoming unstable
Resumo do conteúdo contido na página número 14
JP12: 1-2 SHORT: SMI by PIIX4 ( Single CPU request SMI), Default. SMI 1.4 Install System DRAM Memory The board supports 2pcs 72-pin, 32-bit SIMMs (Single Inline Memory of 4, 8, 16, 32MB to form a memory size between 8MB to 128MB. The SIMMs can be 60ns or 70ns Fast Page Mode (FPM), or Enhanced Data Out (EDO) (BEDO & Parity are not supported). SIMMs must be installed in pairs so that each bank (see Map of ATX-586)contains 64-bit of same memory chips. It is available for 3.3v (power level) U
Resumo do conteúdo contido na página número 15
8MB * 32 DS X 8MB * 32 DS 1MB * 32 SS 8MB * 32 DS 2MB * 32 DS 8MB * 32 DS 4MB * 32 SS 8MB * 32 DS 8MB * 32 DS 16MB * 32SS X 16MB * 32SS 16MB * 32SS 1.5 Install IDE, Enhanced I/O and Front Panel Connectors There is a special design that CN9 is for Key Lock, Sleep/Resume SW, Speaker, IDE LED, TB SW, Reset SW, and Turbo LED. It is convenient for you to connect the cable from front board of Case. CN9: 1-5, Key Lock - Keyboard lock switch & power LED connector. 1. Power LED (+), 2. N/C, 3. GND,
Resumo do conteúdo contido na página número 16
JP17: IR, fast infrared port. PIN-1: IRRX, PIN-2: GND; PIN-3: IRTX; PIN-4: VCC COM1-2/CN1-CN5: Support 16550 high speed PS/2 Mouse CN2: LPT/CN4: Printer port with ECP/ PP. bi-direction. It can be used with external IDE/ SCSI device. AT POWER CONNECTOR/CN6: For normal AT ATX POWER CONNECTOR/CN7: For ATX USB1/: 4-PIN connectors. PIN-1: VCC(5V), PIN-2: USB-, PIN-3: USB+, PIN-4: GND 16 factor style power supply style power supply PS/2 mouse port. 5-pin Mouse: serial ports/ UART.
Resumo do conteúdo contido na página número 17
IDE 1: Primary IDE port to support ATAPI Mode 5 IDE devices IDE 2: Secondary IDE port to support ATAPI Mode 5 IDE devices. FDC/CN8: 1.6 I/O Address and IRQ/DRQ On Board I/O IRQ GAME X X 4 X 3 X 3 X 3 X X X 7 7 7 6 2 PS/2 MOUSE X X 1.7 Jumpers and Connectors List ITEMS DESCRIPTION 3-4 17 Set CPU External Bus Frequency Rate (BF0, BF1) JP7 Set CPU External Bus Frequency Rate (BF0, BF1) JP6 for 512K Cache 1-2 for 256K Cache, JP2 12 3F0-3F7 FDD1 3 (ECP) 3BC-3BF LPT3 3 (ECP) 278-27F LPT2 3 (ECP
Resumo do conteúdo contido na página número 18
Set CPU External Bus Frequency (FS0, FS1, FS2) Set CPU External Bus Frequency (FS0, FS1, FS2) 2-3 Normal CMOS, 3-4 CMOS Clear Select Recovery BIOS 2-3 for 5v Flash BIOS, 1-2 for 12v Indicate the CPU voltage Parallel Port Connector Floppy Drive IDE Drive connector &&& 18 IDE1-2 USB Connector USB1 Front Panel Connector CN9 CN8 ATX Power Supply Connector CN7 AT Power Supply CN6 COM2 CN5 CN4 Keyboard CN3 PS/2 MOUSE Connector CN2 COM1 CN1 J1 Choose Power Supply JP18 IR Connector JP17 JP16 JP15 JP13
Resumo do conteúdo contido na página número 19
19
Resumo do conteúdo contido na página número 20
Chapter 2 AWARD, PnP GREEN BIOS SETUP 2.1 BIOS Setup Powe on the computer and press key immediately and the screen will display you CMOS SETUP UTILITY as ROM PCI/ISA BIOS (2A59GT4A) CMOS SETUP UTILITY AWARD SOFTWARE, INC. Esc : Quit ↑↓←→ F10 : Save & Exit Setup (Shift) F2: Change Color Time, Date, Hard Disk Type....... 2.2 Standard CMOS Setup The STANDARD CMOS SETUP allows user to configure system setting such as current date and time, type 20 : Select Item EXIT WITHOUT SAVING LOAD S
