Resumo do conteúdo contido na página número 1
IP-4GVI63
Series
(Industrial Board)
INSTALLATION GUIDE
Installation Guide Revision A2
6007002463A20
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
© COPYRIGHT All rights reserved. The information contained in this guide has been validated and reviewed for accuracy. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, the Manufacturer assumes no responsibility for errors or omissions. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
Resumo do conteúdo contido na página número 4
CONTENTS SECTION 1 INTRODUCTION 1 1.1 Unpacking IP-4GVI63 Series 1 1.2 Description 3 1.3 Features 3 1.3.1 Graphic & Ethernet 3 1.3.2 Ultra ATA/66/100 4 1.3.3 Hardware Monitoring 4 1.3.4 I/O Shield Connector 4 1.3.5 Power-On/Off 5 1.3.6 IP-4GVI63 Series Overview 5 1.3.7 System Block Diagram 6 1.4 Specifications 7 SECTION 2 INSTALLATIONS 9 2.1 System Installation 9 2.1.1 CPU Installation 9 2.1.2 Heat Sink Installation 10 2.1.3 Memory Module Ins
Resumo do conteúdo contido na página número 5
CONTENTS SECTION 3 AWARD BIOS SETUP 36 3.1 BIOS Instructions 36 3.2 Main Menu 37 3.3 Standard CMOS Features 39 3.4 IDE Adapters 41 3.5 Advanced BIOS Features 43 3.6 Advanced Chipset Features 47 3.7 Integrated Peripherals 50 3.8 Power Management Setup 55 3.9 PnP/PCI Configurations 59 3.10 PC Health Status 60 3.11 Frequency/Voltage Control 62 3.12 Load Fail-Safe Default 64 3.13 Load Optimized Defaults 64 3.14 Supervisor/User Password Setting 65 3.15 Ex
Resumo do conteúdo contido na página número 6
iv
Resumo do conteúdo contido na página número 7
SECTION 1 INTRODUCTION 1.1 Unpacking IP-4GVI63 Series 1. Take out the IP-4GVI63 series unit from the carton box, check if the unit is properly secure in the plastic bag. 2. Check the contents of the carton box: Industrial Board Installation Guide Floppy ribbon cable ATA-66/100 HDD ribbon cable Driver Utility COM2 ribbon cable (1 Set) (for RS-232) 1
Resumo do conteúdo contido na página número 8
Introduction COM3 ribbon cable (1 Set) I/O Shield (for RS-232/422/485) 3. Optional Cable USB2.0 cable (optional) COM4 ribbon cable (optional) (for RS-232/422/485) 2
Resumo do conteúdo contido na página número 9
Introduction 1.2 Description The IP-4GVI63 Series combines the high performance and exceptional ® value of Intel 845GV chipset with a full-featured, new generation, industrial ® board. The Intel advanced 845GV chipset support regular socket 478-pins ® ® ® Intel Pentium 4 / Celeron processors of 1.3GHz and up to 3.06GHz, Furthermore, user can set the jumper to select the mobile CPU, that memory base on the FSB 400/533MHz operation supports DDR SDRAM interface. In the meantime, the 8
Resumo do conteúdo contido na página número 10
Introduction IO Connectivity - ICH4: - 6 Hi-Speed USB2.0 ports - 10/100 Base-TX Ethernet 1.3.2 Ultra ATA/66/100 The ICH4 provides two channel Ultra ATA/66/100 Bus Master IDE controller, that support Ultra ATA/66/100 protocols, perfect for such demanding applications as real-time video, multimedia, and high performance operating system. A new IDE cable is required for Ultra ATA/66/100. This cable is an 80-conductor cable; however the connectors are, of course, backwards com
Resumo do conteúdo contido na página número 11
Introduction 1.3.5 Power-On/Off (Remote) The board has a single 20-pins connector for ATX power supplies. For ATX power supplies that support the Remote On/Off feature, this should be connected to the systems front panel for system Power On/Off button. The systems power On/Off button should be a momentary button that is normally open. The board has been designed with “Soft Off" functions. You can turn Off the system from one of two sources: The first is the front panel Power O
Resumo do conteúdo contido na página número 12
Introduction 1.3.7 System Block Diagram VRM P4 Socket 478-pins Clock ADDR CTRL DATA AGP4X GMCH (845GV) CRT DDR266/333 X2 760 FC-BGA Device IDE Primary ATA100 Intel 82562 10/100 Base-TX IDE Secondary AC97 ICH4 Audio 421 BGA Codec USB Port 1/2 USB PCI BUS USB Port 3/4 USB Port 5/6 Super I/O Super I/O W83627HF W83627HF FWH Keyboard COM 3/4 Port Mouse COM 1/2 Port LPT Port Floppy Figure 2: System Block Diagram 6 PCI SLOTS
Resumo do conteúdo contido na página número 13
Introduction 1.4 Specifications Processor: ® ® ™ - Intel Pentium 4/Celeron processor with socket 478-pins package, Processor operating at 1.3GHz and up to 3.06GHz ® ® ™ - Intel Pentium 4 Mobile processor with socket 478-pins package, Processor operating at 1.2GHz and up to 2.4GHz - System bus frequency at 400/533 MHz FSB Chipset: ® - Intel 82845GV + ICH4 AGPset DRAM Module: - Two 184-pins Socket - For DDR 266/333 SDRAM memory - Support DDR SDRAM up to 2GB (Max.)
Resumo do conteúdo contido na página número 14
Introduction Onboard PCI / IDE: ® - Intel 82801DB (ICH4) controller - PCI rev2.2 Compliant - ACPI Compliant Power Management - PCI bus IDE port with PIO /Ultra DMA-100 x 2 (up to 4 devices) Rear I/O Connectors: - PS/2 mouse and PS/2 style keyboard - D-Sub 25-pins printer port connector D-Sub 9-pins COM1 serial port connector for RS-232 D-Sub 15-pins VGA connector - 2 x USB2.0 connectors - RJ-45 Ethernet and 2 x USB2.0 connectors - Audio for Line-In, Line-Out, MIC phone
Resumo do conteúdo contido na página número 15
SECTION 2 INSTALLATIONS 2.1 System Installation 2.1.1 CPU Installation Carefully follow the steps below in order to install the CPU: 1. Check and confirm that you are going to install correctly CPU type and pin numbers (figure 3). 2. Lift the releasing lever of the Socket 478. 3. Align the pin of the CPU against the pinholes of the Socket 478. Be sure to pay attention to the orientation of the CPU. Figure 3: CPU Socket 4. Push down the CPU into t
Resumo do conteúdo contido na página número 16
Installations Removing a CPU: 1. Before removing the CPU, turn off the IP-4GVI63 Series power; then wait for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cools down. 2. To remove the CPU, lift the releasing lever of the Socket 478. Note: The CPU and the heat radiation plate are hot. They may cause burns. To remove the CPU, reverse the installation steps. 2.1.2 Heat Sink & Retention Module Installation Make sure that good contact is ma
Resumo do conteúdo contido na página número 17
Installations 2.1.3 Memory Module Installation Figure 5 display the notch marks and what they should look like on your DIMM memory module. DIMMs have184-pins and two notches, that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90-degree angle and pressing straight down (figure 6) until it fits tightly into the DIMM socket. Figure 5: DIMM Memory and 184-pins Socket Figure 6: Memory In
Resumo do conteúdo contido na página número 18
Installations Carefully follow the steps below in order to install the DIMMs: 1. To avoid generating static electricity and damaging the DIMM, ground yourself by touching a grounded metal surface or using a ground scrap before you touch the DIMM. 2. Do not touch the connector of the DIMM. Dirt residue may cause a malfunction. 3. Hold the DIMM with its notch to the front side of the IP-4GVI63 Series and insert it completely into the socket. A DIMM should be inserted into the inner
Resumo do conteúdo contido na página número 19
Installations 2.1.4 Setting Jumpers There are jumpers on the system board of the IP-4GVI63 Series. You can set the jumpers to make the necessary operations. Figure 7: Jumper Connector For any three-pins jumpers (figure 7), the jumper setting is 1-2 when the jumper connects pin 1 and 2. The setting is 2-3 when pin 2 and 3 are connected and so on. You could see one of the lines surrounding jumpers is thick, which indicates pin NO.1. To move a jumper from one p
Resumo do conteúdo contido na página número 20
Installations 2.2 Board Layout Jumper & Connector Location KBMS1 JP1 POWER FAN FAN2 ATX1 FAN1 COM1 CPU FAN LPT1 VGA1 ATX2 USB1 USB2 LAN CN1 J1 AGP1 ADD ONLY PCI1 WOL1 PCI2 BAT1 PCI3 JP3 IDE1 IDE2 PCI4 JBAT1 J2 COM2 PCI5 FAN3 FDD1 PCI6 J3 JCN1 JPB1 JCN2 JPB2 USB3 FAN4 14 REV:1.0 CD IN1 AUX IN1 IP-4GVI63 DIMM1 DIMM2 CHASSIS FAN
