Resumo do conteúdo contido na página número 1
XP-15 Vector Processor
User Guide
Any trademarks or registered trademarks used in this document belong to the companies that own them.
Copyright © 2001, Texas Memory Systems, Inc. All rights are reserved. No part of this work may be
reproduced or used in any form or by any means - graphic, electronic or mechanical, including photocopying,
recording, taping, or information storage and retrieval systems - without permission of the copyrigh
Resumo do conteúdo contido na página número 2
Table of Contents Chapter 1 - Introduction ........................................................................................................................ 1-1 1.1 Related Texts .................................................................................................................................... 1-1 1.2 Typographical Conventions ............................................................................................................... 1-1 Chapter 2 - Overview...
Resumo do conteúdo contido na página número 3
Chapter 1 - Introduction The XP-15 vector processor is a PCI card that can be installed in a workstation and that delivers SuperComputer-class vector processing performance. This document is concerned with the installation and set-up of the XP-15. Chapter 2 gives an overview of the functionality of the XP-15. Chapter 3 describes the hardware and software installation of the XP-15. Chapter 4 describes a programming example for the XP-15 for use in an X-Midas environment. 1.1 Relat
Resumo do conteúdo contido na página número 4
Chapter 2 - Overview The XP-15 is a high-performance vector processor implemented on a single card suitable for installing in a PCI Local Bus card slot in a general-purpose computer. The XP-15 is based on the 8 GFLOPS TM-44 DSP chip from Texas Memory Systems and includes four 32 MB banks of fast local memory. The XP-15 is programmed by making calls to move data from host memory to XP-15 local memory, to perform one or more vector processing operations on the data, and to move results ba
Resumo do conteúdo contido na página número 5
Chapter 3 - Installation The XP-15 vector processor has currently been tested in the following computer platforms: q Compaq ALPHASERVER ES40. q Compaq ALPHASERVER DS10. XP-15 Software is currently available for the following operating system revisions: q TRU64 (Digital Unix) 5.1 3.1 Installing the XP-15 Hardware 3.1.1 Jumper Settings The XP-15 has no user-selectable jumpers. 3.1.2 Installing the XP-15 in a Computer Power-off the computer system. Select a suitable vacan
Resumo do conteúdo contido na página número 6
Enter the mount point of the CDROM - /cdrom What directory do you want to install the XP-15 software to - /usr/tms The XP15 software will be installed from /cdrom to /usr/tms Is this correct (y/n)?yes Installing the XP15 software. Finished installing the USER part of the XP15 software. The final step in installing the XP15 is to install the driver using a script that also asks a few questions. A typical run is shown, again with user responses underlined. #cd /cdrom #./inst
Resumo do conteúdo contido na página número 7
Xpmon[0]> t99 Running all tests: Performing SPRAG tests … . . testing many functions . . All tests should run without any errors. If any errors occur please contact Texas Memory Systems. 3.3.2 Programming Example Confidence Test The XP-15 confidence test is located on the XP-15 software CDROM in the examples/cfft directory, and a listing of the source code can be found in Appendix A. This simple application creates a signal co
Resumo do conteúdo contido na página número 8
The sample application is executed with one parameter on the command line: the XP-15 unit to be used. Typically, this will be unit 0 (zero) unless multiple XP-15s are installed in this host computer. % cfft -x 0 XP-15 Confidence test performing a 1048576 point CFFT on XP-15 #0 Allocate memory for test signal and FFT results Clearing results buffer Creating test signal Performing CFFT Wait for all XP-15 functions to complete First 10 values of CFFT results: 00: [ 16.0000, 0.0000]
Resumo do conteúdo contido na página número 9
Chapter 4 - X-Midas Programming Example: XTMIC This chapter describes the X-Midas programming example, how to execute it, and how to use it as a template for XP-15 applications. The source code is located on the XP-15 software CDROM in the examples/xtmic/ directory. 4.1 Overview The X-Midas programming example is a less robust version of the SAMTMIC software that currently runs on the SAM-450. The XP-15 implementation, referred to as the XTMIC, performs the same basic processing as
Resumo do conteúdo contido na página número 10
The XTMIC macro requires two command line parameters that determine which files the XTMIC will use for its processing. The input files must contain 16-bit integer data, and must have at least 1507328 elements. Assuming the input files are called input_a and input_b, the command line required to run the XTMIC would look like: % X-Midas> run_x input_a input_b XTMIC> Starting xtmic demo. XTMIC> Setting up files/pipes. XTMIC> Initializing XP15 buffers. XTMIC> Entering loop. Total i
Resumo do conteúdo contido na página número 11
Appendix A – XP-15 Confidence Test /************************************************************************** Copyright (c) 2001 by Texas Memory Systems, Inc. Texas Memory Systems, Inc. 11200 Westheimer #1000 Houston, TX 77042 (713) 266-3200 Module Name: cfft.c Package: CFFT demo Version: $Revision: $ Release Date: $Date: $ Description: XP15 FFT demo **************************************************
Resumo do conteúdo contido na página número 12
*/ while ((cc = getopt(argc, argv, "hx:")) != EOF) { switch (cc) { case 'x': xp15 = atoi(optarg); break; case 'h': case '?': default : help(); } } /* * Print some useful information */ printf("XP-15 Confidence test performing a %d point CFFT on XP-15 #%d\n", fft_size, xp15); /* * Allocate host memory for a test signal */ printf("Allocate me
Resumo do conteúdo contido na página número 13
status = vmov((TMS_FLOAT *)signal, (TMS_FLOAT *)cu, fft_size * 2); if (status < 0) sam_error(status); /* * Perform the CFFT */ printf("Performing CFFT\n"); status = cfft(cu, /* input buffer */ NULL, /* Twids not needed by XP-15 */ cy, /* output/scratch buffer */ 1, /* repeat value - 1 this time */ 1.0
Resumo do conteúdo contido na página número 14
results[ii].imag); } ecount++; } } if (ecount == 0) printf ("XP-15 confidence test completed with no errors\n"); else printf ("XP-15 confidence test completed with %d errors\n", ecount); exit(0); } /********************************************************************** Function: help Description: display help screen, and exits Arguments: none Returns: none *********************************************
Resumo do conteúdo contido na página número 15
Appendix B – PCI Local Bus Specifications The XP-15 interface adapter is a 3.3V signaling environment expansion card, as defined by the PCI Local Bus Specification 2.0, 2.1, and 2.2. This means that the XP-15 is designed to operate exclusively in 3.3V signaling environment system motherboards. During the development of the XP-15, the liberty was taken to add a second key slot on the PCI edge connector. This allows for operation and testing in most 5V signaling environment motherbo
Resumo do conteúdo contido na página número 16
Appendix C – XP-15 Hardware Control and Status Registers The XP-15 is a custom hardware adapter designed to provide processing power to a host computer (DEC Alpha, Intel PC, etc..). The XP-15's data bus is 32-bits or 64-bits wide (depending on the host PCI slot). The following tables describe the XP-15's hardware control registers. Each register is classified as read only, write only, or read/write. The least significant bit of each register is always tied to the least significa
Resumo do conteúdo contido na página número 17
3 ECHO RO Indicates the XP-15 has returned an ECHO packet 2 SPR RO Indicates the XP-15 has returned an SPR packet 1 DIAG RO Indicates the XP-15 has returned a diagnostic packet 0 STAT RO Indicates the XP-15 has returned a status packet Low PCI SN command address register (32 bits, R/W) Bit # Name Type Description 31-3 NA R/W This register is used to establish the low 32-bits of the PCI address for SN commands to the XP-15. This register consists of the bottom 32-bits of a 32-bit co
