Краткое содержание страницы № 1
REV. E
TM
Cooler is Better!
USER’S
MANUAL
BLAST CHILLERS (SHOCK FREEZERS)
MODEL AP24BC250-3
MODEL AP24BCF300-3
MODEL AP40BC350-3
MODEL AP40BCF450-3
American Panel Corporation
5800 S.E. 78th Street, Ocala, Florida 34472-3412
Phone: (352) 245-7055 Fax: (352) 245-0726
E-mail: service@americanpanel.com
Краткое содержание страницы № 2
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual INDEX INTRODUCTION 3 CONTROLLER FEATURES 3 OPERATING MODES 3 AUTOMATIC MODE 3 MANUAL MODE 4 OPERATING CYCLES 4 PRINTER (OPTIONAL) 4 PC CONNECTION (OPTIONAL) 4 INSTALLATION OF REMOTE UNITS 5 REQUIREMENTS TO BE MET DURING INSTALLATION (8 STEPS) 5 INSTALLATION AT THE SAME LEVEL 5 INSTALLATION AT DIFFERENT LEVELS 6 CONNECTION PIPING FOR REMOTE CONDENSING UNITS 6 INSTALLATION 7 WARNINGS 7 PREPARATION 7 INSTALLATION 7 LOCA
Краткое содержание страницы № 3
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual MANUAL SOFT CYCLE PARAMETERS PROGRAMMING 22 MANUAL HARD CYCLE PARAMETERS PROGRAMMING 23 MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 24 3. RECIPE NAME PROGRAMMING 25 OPERATION 26 1. AUTOMATIC MODE - SOFT CHILL 26 2. MANUAL MODE - SOFT CHILL 27 3. HARD CHILL CYCLE 28 4. SHOCK FREEZE CYCLE 29 5. UV (STERILIZATION) CYCLE 29 6. DEFROST CYCLE 29 7. HEATED FOOD PROBE 30 8. PREPARING AND USING THE OPTIONAL PRINTER 31 9. TO CLEAR DA
Краткое содержание страницы № 4
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual INTRODUCTION Blast Chiller Models AP24BC250-3 and AP40BC350-3 are used to rapidly chill cooked foods to temperatures suitable for refrigerated storage. They are capable of lowering the core temperature o o of most foods from 160 F to 40 F in 90 minutes. Chiller/Freezer Models AP24BCF300-3 and AP40BCF450-3 have the same chilling capabilities as the Blast Chiller Models and when the shock o freezing option is selected, are capab
Краткое содержание страницы № 5
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual MANUAL MODE Operating time is set manually, by the operator, for the meal that has been chosen. Air temperature is controlled by the air probe. If the food probes have been inserted into the food they will provide temperature readouts only. The unit will automatically switch into the holding mode at the end of the cycle. OPERATING CYCLES The operator can choose from the following 6 operating cycles: MODE FOOD TEMP. US
Краткое содержание страницы № 6
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual INSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURING INSTALLATION (8 STEPS) COMPRESSOR FIG. 1 FIG. 2 1. Inclination of the piping. 2. Fastening of brackets on insulated piping. FIG. 3 FIG. 4 3. Airtight welding. 4. Create the vacuum and load the line. 5. Check for leaks. 6. Open the shut-off valves (A & B, FIG.4) on both sides of remote unit and of cabinet. 7. Check the exact
Краткое содержание страницы № 7
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual INSTALLATION AT DIFFERENT LEVELS If the remote condensing unit is installed at a higher level than the cabinet (FIG. 6) insert a siphon in the return line at every 6 ft. of difference in height. If the remote condensing unit is installed at a lower level than the cabinet (FIG. 7) it is not necessary to insert any siphons. FIG. 6
Краткое содержание страницы № 8
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual INSTALLATION WARNINGS READ ALL OF THE INSTRUCTIONS IN THIS MANUAL BEFORE YOU ATTEMPT TO INSTALL THE EQUIPMENT. ALWAYS DISCONNECT THE UNIT FROM THE POWER SOURCE BEFORE PERFORMING ANY SERVICE OR MAINTENANCE. INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED SERVICE AGENCY APPROVED & AUTHORIZED BY AMERICAN PANEL CORPORATION. DOING OTHERWISE MAY VOID THE WARRANTY. Note: Any changes made to the equipment with
Краткое содержание страницы № 9
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual ELECTRICAL AND REFRIGERATION SPECIFICATIONS CABINET REMOTE CONSENSER MODEL VOLTAGE POWER SUPPLY BTU/H AT 14°F EVAP. TEMP. TYPE AMPS CORD & 105°F COND. TEMP. AP24BC250-3 208/3/60 8 14-4 25,000 MEDIUM TEMP. -10°F/+40°F AP24BCF300-3 208/3/60 8 14-4 50,000 MEDIUM/LOW TEMP. -40°F/+40°F AP40BC350-3 208/3/60 10 14-4 35,000 MEDIUM TEMP. -10°F/+40°F AP40BCF450-3 208/3/60 10 14-4 70,000 MEDIUM/LOW TEMP. -40°F/+40°F NOTES: 1. T
Краткое содержание страницы № 10
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual l. Make sure that the fans inside the cabinet rotate clockwise. m. Make sure that the cabinet has been leveled. SPACES AROUND THE CABINET • At least 15" clear space is required above the unit for service. • At least 6" clear space is required on both sides of the cabinet. • At least 6" clear space is required on the rear of the cabinet for drain hookup and maintenance. • Enough space should be provided in front
Краткое содержание страницы № 11
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual USING THE HURRICHILL™ TECHNOLOGY BLAST CHILLING All cooked food rapidly loses its quality and aroma if it is not served promptly. Natural bacteria growth, the main reason why food becomes stale, takes place at an exponential rate between 140°F and 40°F. However lower temperatures have a hibernating effect that increases as the temperature drops, thereby gradually reducing bacterial activity until it stops altogether. Only
Краткое содержание страницы № 12
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual PANNING AND LOADING PANNING 1. Standard pan depth is 2-1/2”. Other depths can be used but are not recommended as their use would require an increase in the cycle time. 2. Stainless steel or aluminum pans are recommended, as plastic containers will increase the chilling time. 3. Crockery or stainless steel cylinders, 6” dia. and 10” max. height, are acceptable. 4. Slack filled Cryovac bags can be used if placed on wire
Краткое содержание страницы № 13
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS 12
Краткое содержание страницы № 14
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual KEYBOARD KEYS ON/OFF & START/STOP CYCLE KEYS ON/OFF SOFT CYCLE START/STOP HARD CYCLE SHOCK CYCLE PROGRAMMING KEYS AUTOMATIC CYCLE UP MANUAL CYCLE DOWN UV LIGHT CYCLE SELECT DEFROST CYCLE ENTER PRINT HEAT PROBE CYCLE KEY COMBINATIONS Initial Programming state – to initially set the device o With the display reading "OFF", press and hold (“START/STOP”) for 5 seconds Cyc
Краткое содержание страницы № 15
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual PROGRAMMING 1. INITIAL PROGRAMMING NOTE: Initial programming is preset at the factory. Use this section only if changes are desired. If no changes are to be made, skip to Page 17 ( 2. Programming the cycles ). OFF a. With the display reading "OFF", press ("START/STOP") for a few seconds. INITIAL PROGRAMMING b. To change the language, press or then SELECT LANGUAGE ENGLISH ENGLISH Blinks press
Краткое содержание страницы № 16
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual INITIAL PROGRAMMING g. To set the day, press or then press SET DAY 03(day) 03 Blinks . INITIAL PROGRAMMING h. To set the hour, press or (be sure to continue to press the buttons until the hour and "AM" SET TIME 10(hours) 10:25 AM Blinks or "PM" show correctly) then press . INITIAL PROGRAMMING i. To set the minutes, press or then press SET TIME 25(minutes) 10:25 AM Blinks . INITIAL PROGRAMMING
Краткое содержание страницы № 17
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual The low food alarm temperature should be left at o INITIAL PROGRAMMING 35 F. However, to make a change: SOFT & HARD LOW FOOD ALARM 35 Blinks o. To change the temperature, press or 35 °F then press . INITIAL PROGRAMMING p. To change to YES or NO, press or then SHOCK FREEZE? YES Blinks YES * press . * YES for shock freezers (AP24BCF300-3, AP40BCF450-3) NO for blast chillers (AP24BC250-3, AP40BC350-3)
Краткое содержание страницы № 18
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual For YES, the display will show: INITIAL PROGRAMMING The printer baud rate should be left at 1200. However, to make a change: PRINTER BAUDRATE 1200 Blinks 1200 x. To change the baud rate, press or then press . INITIAL PROGRAMMING y. To change the timing, press or then PRINT & SAVE EVENTS 15 Blinks EVERY 15 MIN press . INITIAL PROGRAMMING z. To change to YES or NO, press or then PRINT D
Краткое содержание страницы № 19
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING PARAM. PROGRAMMING The LED for "A" will be "ON". AUTOMATIC MODE The LED'S for cycles will be blinking. CHOOSE PROGRAMMING CYCLE c. Press . The LED for "SOFT" will be steady "ON". PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE d. To change the temperature, press or LOW AIR TEMPERATURE 28 Blinks 28 °F then press . PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE e. To change the
Краткое содержание страницы № 20
AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual then press . o * 0 F for shock freezers (AP24BCF300-3, AP40BCF450-3) o 10 F for blast chillers (AP24BC250-3, AP40BC350-3) PARAM. PROGRAMMING AUTOMATIC HARD CYCLE k. To change the temperature, press or HIGH AIR TEMP PART 1 10 Blinks 10 °F ** then press . o ** 10 F for shock freezers (AP24BCF300-3, AP40BCF450-3) o 20 F for blast chillers (AP24BC250-3, AP40BC350-3) PARAM. PROGRAMMING AUTOMATIC HARD CYCLE l. T
