Руководство по эксплуатации Sunrise Medical One-Arm Drive Quickie IRIS

Краткое содержание страницы № 1

One-Arm Drive Option
Supplement to Quickie 2, Quickie TS, Quickie IRIS,
Zippie 2, Zippie GS, Breezy Series
User
Instruction
Manual
Note: This supplement contains information on the
assembly and adjustments for the One-Arm Drive
Components of a Quickie 2, Quickie TS, Quickie IRIS,
Zippie 2, Zippie GS & Breezy Series wheelchairs
ONLY.
Please refer to the Quickie 2, Quickie TS, Quickie IRIS,
Zippie 2, Zippie GS, or Breezy Series User Instruction
Manual for Safety Tips,Troubleshooting, Maintenance,

Краткое содержание страницы № 2

1. SUNRISE LISTENS II. TABLE OF CONTENTS SUNRISE LISTENS 1. SUNRISE LISTENS .......................................................................... 2 Thank you for choosing the One-Arm Drive Option. We want to hear your 11. TABLE OF CONTENTS ................................................................ 3 questions or comments about this manual and the service you receive from your supplier. Please feel free to write or call us at the address and telephone 111. SPECIFICATIONS AND FEATURES

Краткое содержание страницы № 3

III. SPECIFICATIONS AND FEATURES IV. ASSEMBLY A. INSTALLING AXLES 1 1. Installation 2 6 a. Mount axle plates on each side of the chair Breezy 500 & 510 (Fig. 1), Breezy 600 & Quickie LXI (Fig. 2), Zippie GS (Fig. 1a), Breezy (Fig. 3), Zippie 2 (Fig. 1a), Quickie TS (Fig. 4), and Quickie IRIS (Fig. 5) must use bushings for proper installation. NOTE: DO NOT use camber with one-arm drive. 5 1 4 2 3 5 Fig. 1 Fig. 1a 4 3 Quickie TS (Rear views of the wheelchairs) ONE-ARM DRIVE 1. Inner Handrim Fig.

Краткое содержание страницы № 4

IV. ASSEMBLY IV. ASSEMBLY 2. Opposite Side Assembly (Fig. 8) B. INSTALLING HUBS a. Add one washer (5a) to axle (1). 4 1. Installation (Figs. 5 & 6) 6 b. Insert axle with washer through bearings a. Thread screw (4) partially through 3 in axle plate. threaded hub (3) to position hubs on 1 5 5a c. Add spacer (2) to axle. both sides of wheel. 3 d. Add wheel (4) to axle. 1 b. Insert alignment tool or axle with key 2 2 e. Insert key (3) into keyway on axle (1). (2) through hub and wheel assembly, f.

Краткое содержание страницы № 5

V. ADJUSTMENTS V. ADJUSTMENTS A. REAR AXLES - CENTER OF BALANCE 1. Notes Always adjust rear wheel locks after you a. The position of the rider’s weight relative make any change to the axle position. Make sure lock arms embed in tires at least to where you set the rear axles 1/8 inch when locked. If you fail to do so, determines the center of balance. the locks may not keep the rear wheels These are the most important from rolling. Refer to User Instruction adjustments on your chair. Manual for

Краткое содержание страницы № 6

V. ADJUSTMENTS V. ADJUSTMENTS E. REVERSING ONE-ARM DRIVE 4. Quickie TS (Fig. 14) b MOUNTING SIDES Quickie IRIS (Fig. 15) a The one-arm drive may be mounted on a. The center of gravity is adjusted by either side of the chair. moving the rear axle forward or back- b Follow one-arm drive assembly instruc- ward to the additional holes located tions in reverse order to disassemble. along the frame. c. To remount on opposite side follow b. Rotating the entire axle brackets allows a one-arm drive assem

Краткое содержание страницы № 7

Sunrise Medical, Inc. 7477 East Dry Creek Parkway • Longmont, Colorado • 80503 USA (303) 218-4500 or (800) 333-4000 in Canada (800) 263-3390 ©2003, Sunrise Medical 7.03 930331 Rev. F