Краткое содержание страницы № 1
EN-8500
EN-8500
18” LCD Monitor With TV Tuner
User’s
Manual
By Envision Peripherals, Inc.
www.envisionmonitor.com
Before operating your monitor,
please read this manual
thoroughly.
Краткое содержание страницы № 2
EN-8500 TABLE OF CONTENTS COVER ……………………………………………………………………… TABLE OF CONTENTS …………………………………………………... 1 FOR YOUR SAFETY ……………………………………………………… 2-3 SPECIAL NOTES ON LCD MONITOR …………………………………. 4 GENERAL NOTES ………………………………………………………… 5 FEATURES ………………………………………………………………… 6 PACKAGE CONTENTS ………………………………………………….. 7 INSTALLATION INSTRUCTIONS ………………………………………. POWER CORD ……………………………………………………….. 8 BASIC CONNECTIONS ……………………………………………… 9 PREPARING TO INSTALL THE OPTIONAL WA
Краткое содержание страницы № 3
EN-8500 FOR YOUR SAFETY Before operating the monitor please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential inst
Краткое содержание страницы № 4
EN-8500 SAFETY PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufac
Краткое содержание страницы № 5
EN-8500 SPECIAL NOTES ON LCD MONITORS NOTES The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of thefluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD panel used in this monitor is a very high technology prod
Краткое содержание страницы № 6
EN-8500 GENERAL NOTES S • Set your resolution to 1024 x 768 @ 60Hz refresh rate for optimum display quality. • The screen surface is very soft. Do not rub, touch or tap the screen surface with sharp object such as pen or pencil. This contact may scratch or damage the screen. These damages are not covered under the warranty. • Turn your computer OFF before installing your new monitor. Refer to your computer manual for the proper shut down procedure. • This is a Plug & P
Краткое содержание страницы № 7
EN-8500 BEFORE YOU OPERATE THE MONITOR FEATURES FEATURES • 18” TFT Color LCD Monitor with TV Tuner • Composite & S-Video Inputs • PIP (Picture-in-Picture) • Crisp, Clear Display for Windows • Recommended Resolutions: 1024 X 768 @60Hz ® • EPA ENERGY STAR • Ergonomic Design • Space Saving, Compact Case Design 6
Краткое содержание страницы № 8
EN-8500 CHECKING THE CONTENTS OF THE EN-8500 PACKAGE The product package should include the following items: 1. EN-8500 LCD Monitor with TV Tuner 2. Quick Start Guide 3. Remote Control with Batteries 3. Power adaptor & Power Cord 4. Driver Disk Containing Windows 95/98/ME/2000/XP INF & ICM Files 5. PC Stereo Cable 6. D-Sub Cable Quick Start Guide (QSG) Remote Control w/batteries Monitor Power Adapter Power Cord Driver Disk PC Stereo Cable D-Sub C
Краткое содержание страницы № 9
EN-8500 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS POWER CORD Power Source: 1. Make sure the power cord is the correct type that required in your area. 2. This LCD monitor has a universal power supply that allows operation from100 - 240V AC voltage area (No user adjustment is required.) 3. Connect the Power Adapter’s DC cord into your LCD monitor’s power input socket. Then connect the male side of the power cord into a 3-pin AC power outlet. Connect th
Краткое содержание страницы № 10
EN-8500 INSTALLATION INSTRUCTIONS (cont) BASIC CONNECTIONS NOTE: 1. Connect the Power Adapter DC Cord to the monitor’s 12VDC Input. 2. Connect one end of the D-Sub cable to the monitor’s D-Sub Input. 3. Connect the other end of the D-Sub cable to the computer’s VGA video output port. 4. Connect the antenna or Cable TV to the monitor’s TV input port. 5. Connect the power cord to the AC power outlet. 6. Connect the other end to the monitor’s power adapter. Ca
Краткое содержание страницы № 11
EN-8500 INSTALLATION INSTRUCTIONS (cont) Preparing To Install The Optional Wall Mount Arm (not supplied): This monitor can be attached to a wall mounting arm you can purchase separately. Turn the power OFF then dis-connect the cables from the monitor before performing the procedure below. Lay the monitor face down on a soft surface. 1. Press the “FOLD” button on the base of the monitor. 2. Fold the base so it is flush against the ba
Краткое содержание страницы № 12
EN-8500 3. INSTALLATION INSTRUCTIONS (cont) Attaching The Optional Wall Mount Arm (not supplied): Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Insert the 4 screws into the holes and tighten. 3. Insert the cables into the slot on the back of the monitor. NOTE: The Envision EN-8500 is in complian
Краткое содержание страницы № 13
Краткое содержание страницы № 14
EN-8500 ADJUSTING THE VIEWING ANGLE INSTALLATION INSTRUCTIONS • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s tilt angle. • You are able to adjust the monitor’s tilt angle from -5° to 25°. NOTES • Do not touch the LCD screen when you change the angle. It may cause damage or break the
Краткое содержание страницы № 15
EN-8500 OPERATING INSTRUCTIONS Press the Power Switch to turn the monitor ON or OFF. The other control knobs are located at the front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • Press the Power Switch to turn ON the monitor. The power indicator will light up. USER CONTROLS No. Name
Краткое содержание страницы № 16
EN-8500 OPERATING INSTRUCTIONS (cont) USER CONTROLS (cont) 7. MENU ALL Modes: Open OSD menu or select the highlighted FUNCTION when OSD menu is already active. 8. A-SEL PIP Mode: Audio source select (PIP audio or PC audio) 9. V-SEL ALL Modes: Video source select 10. Power Indicator Green: Power ON AMBER: OFF Mode 11. Power Switch All Modes: Switch monitor ON/OFF. 15
Краткое содержание страницы № 17
EN-8500 OPERATING INSTRUCTIONS (cont) REMOTE CONTROL 16
Краткое содержание страницы № 18
Краткое содержание страницы № 19
EN-8500 SELECT THE DIFFERENT INPUT SOURCE There are seven display modes that you can choose by V-SEL key. PC Mode : Display the video signal from the PC. PC+TV Mode (PIP mode): Display the TV signal in PIP and the background is PC video signal. PC+S-VIDEO Mode (PIP mode): Display the S-VIDEO signal in PIP and the background is PC video signal. PC+VIDEO Mode (PIP mode): Display the VIDEO signal in PIP and the background is PC video signal. TV Mode : Display the si
Краткое содержание страницы № 20
EN-8500 SCREEN CONTROLS PC SCREEN ADJUST Menus – Available in PC & PIP mode. Icon Menus and Sub-menus Function Descriptions BRIGHTNESS Adjust the picture brightness. Adjust the picture contrast. CONTRAST FOCUS Adjust the horizontal noise TRACK Fine tune the horizontal noise CLOCK Adjust the vetical noise Adjust the horizontal position of the picture. H.POSITION V.POSITION Adjust the vertical position of the picture. Adjust the color from redis
