Краткое содержание страницы № 1
73528
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Age: 1½ years - 5 years.
Weight Limit: 50 lbs. (23 kg).
Tools needed for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (all not included).
www.fisher-price.com
1
Краткое содержание страницы № 2
Fasteners Consumer Information WARNING To avoid serious injury: • Adult supervision is required. Cap Nut – 1* • Never use near cars and other motor vehicles, near streets, steps, sloped driveways, hills, *Note: For your convenience, an roadways, alleys, swimming pool areas or extra cap nut is included. other bodies of water. • Always wear shoes or sneakers. • Never allow more than one (1) rider. 3 #8 x / " Screw - 13 4 3 #10 x / " Screw - 11 4 #8 x 3" Screw – 1 Note: Tighten and loosen the
Краткое содержание страницы № 3
Parts Note: The base/handle assembly can be attached to the trike in either the Ride-on Rocker (page 9) Seat Pin or Learn to Pedal (page 10) mode. Seat Parts not shown: Assembly Tool and Label. Handlebar Frame Cover 2 Base/Handle Covers Frame Straight Axle 2 Rear Wheels Cap Nuts Footrest Fork Handle Bottom 2 Wheel Caps 2 Fork Covers Base Handle Pin Handle Top Front Wheel 4 Pedal Axle Covers Assembly 3
Краткое содержание страницы № 4
Assembly CAUTION Frame This product contains small parts in its Rear Wheel unassembled state. Adult assembly is required. Wheel Hole Cap Hole • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry, cloth before assembling this product. Straight Axle 2 Bottom View • Turn the frame upside down. Straight Axle • Insert the straight axle assembly through the holes in the rear of the frame. • Fit the wheel cap
Краткое содержание страницы № 5
Assembly Assembly Tool Rear Wheel Wheel Cap Spoke Side Up Cap Nut Straight Axle 4 • Fit the wheel cap into the center of the wheel. Tap the wheel cap with a hammer to secure it to the wheel. • Set the frame assembly aside. Pedal Axle Cover Assembled Rear Wheel Scrap Block 3 of Wood Pedal Axle • Turn the frame on its side with the exposed end of the straight axle up. Slot • Place the assembled rear wheel on the scrap block 5 of wood. Pedal Axle Metal Tab Cover • Slide the other rear whee
Краткое содержание страницы № 6
Assembly Front Wheel Assembly Handlebar Fork Arms Fork Cover Frame Neck Fork Post FIRST, insert the screw " ¾ so that is visible. THEN, tighten the screw. ¾" 6 Fork Covers Groove Pedal Axle 7 • Place the front wheel assembly between the fork arms so that the pedal axle fits into the groove at the bottom of each fork arm. • Turn the frame upright. • Place a fork cover over the pedal axle on one fork arm. • Insert the fork post up through • Insert two #10 x ¾" screws into the fork cover the
Краткое содержание страницы № 7
➥ Assembly Knobbed End Seat Frame Opening Footrest Footrest ➥ Knobbed End 2 8 1 3 • Insert the knobbed end of the foot- rest up through the opening in the 1 underside, center of the frame . 2 • Rotate the footrest ¼ turn . Top View • Slide the footrest toward the handlebar as far as it will go until Seat Mount 10 the top of the footrest is Seat Mount Adjustment Holes positioned over the opening’s rectangular cut-out. • Lower the knobbed end of the footrest into the rectangular 3 cut-
Краткое содержание страницы № 8
Assembly 13 11 Seat Pin • Insert 13 - #8 x ¾" screws into the handle top • While pushing down on the seat, insert the seat pin and tighten. through the hole in the seat and into a seat mount adjustment hole. Handle Top Base Wheel Grooves Retainers Handle Bottom 14 12 Base/Handle • Place the base/handle assembly on a flat surface so that • Fit the handle top and bottom to the end of the base, the wheel retainers are upright. as shown. • Fit the trike onto the base/handle assembly so that th
Краткое содержание страницы № 9
Assembly Ride-on Rocker IMPORTANT! Be sure to adjust the seat in the most Flared End forward position for Ride-on Rocker mode. Trike Handle Cover 15 Base/Handle • Position the base/handle covers so that the flared end faces the front of the trike. • Fit the base/handle covers onto the trike rear frame near the rear wheels. • Insert two #10 x screws into each base/handle cover ¾" and tighten. Assembly is now complete. Label Application Handle Center of Label Place Center of Label Here Base
Краткое содержание страницы № 10
Learn to Pedal Trike Learn to Pedal Trike Base/Handle 2 • Rotate the base/handle to the upright position. 3 Base/Handle Handle Pin • Insert the handle pin through one side of the base/handle, through the holes in the back of the frame and out through the hole in the other side of the base/handle. Make sure the handle pin “snaps” into place. • Pull on the handle pin to be sure it is secure. Handle Pin Front Wheel 1 Wheel Retainer Wheel Retainer • If you are converting from the ride-on rocker m
Краткое содержание страницы № 11
Pedal Trike Base/Handle 1 Handle Pin • If you are converting from the learn to pedal trike mode, remove the handle pin from the base/handle and the back of the frame. Base/Handle 2 • Rotate the base/handle down, under the trike, to the ride-on rocker position. 11
Краткое содержание страницы № 12
Pedal Trike Storage Flared End Base/Handle Cover Handle Cover Handle Pin 3 Base/Handle • Remove the screws from the base/handle covers. • Remove the base/handle covers. • Remove the base/handle. Handle Cover Helpful Hint: To store for future use, position the handle covers with the flared end upright and attach them to the handle using the four screws. Insert the handle pin into either the holes in the base/handle or through the holes in the retainers. Store the base/handle in a safe place
