Resumen del contenido incluido en la página 1
GUITAR AMPLIFIER GUITAR AMPLIFIER
Owner’s Manual
GUITAR AMPLIFIER GUITAR AMPLIFIER HEAD
Mode d’emploi
Bedienungsanleitung
Manual del Usuario
Manuale di Istruzioni
Handleiding
SPEAKER ENCLOSURE SPEAKER ENCLOSURE
Resumen del contenido incluido en la página 2
FCC INFORMATION (U.S.A.) tions does not guarantee that interference will not occur in all 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! installations. If this product is found to be the source of inter- This product, when installed as indicated in the instructions ference, which can be determined by turning the unit “OFF” contained in this manual, meets FCC requirements. Modifica- and “ON”, please try to eliminate the problem by using one of tions not expressly approved by Yamaha may void your a
Resumen del contenido incluido en la página 3
IMPORTANT SAFETY INSTRUCTIONS INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK, AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST. WARNING- When using any electrical or electronic prod- 8. This product was NOT designed for use in wet/damp loca- uct, basic precautions should always be followed. These precau- tions and should not be used near water or exposed to rain. Exam- tions include, but are not limited to, the following: ples of wet /damp locations are; near a swimming po
Resumen del contenido incluido en la página 4
Thank you for purchasing a Yamaha DG Series Guitar Amplifier. The DG Series Digital Guitar Amplifiers were initially conceived and entirely developed by Yamaha. These digital guitar amps deliver powerful tube amp sounds and offer superior stability compared to other tube amplifiers. With eight different amp type settings from which to choose, the DG Series Guitar Amplifiers allow you to create a wide variety of original sounds. A total of 128 sound settings can be stored in their internal memory
Resumen del contenido incluido en la página 5
Contents DG100-212A/DG80-210A/DG80-112A/DG130HA Precautions................................................................... 5 Utility Mode ................................................................. 12 Creating a Program Change Table ............................... 12 The Panel Controls ...................................................... 6 Set the MIDI Receive Channel...................................... 12 Front Panel ..........................................................
Resumen del contenido incluido en la página 6
DG100-212A/DG80-210A/DG80-112A/DG130HA The Panel Controls * The DG100-212A is shown in the illustration. Front Panel q w e r t y u i o !0 !3 !4 !5 !7 !1 !2 !6 * When the Amp Select button is pressed, knobs r – y return to their preset q Input Jack (INPUT HIGH, LOW) positions (GAIN and MASTER =7, Tone Controls all = 5). The position of Connect the guitar to this jack. Guitars with a high output level should the REVERB knob does not change. be connected to the LOW jack. Those with low output lev
Resumen del contenido incluido en la página 7
DG100-212A/DG80-210A/DG80-112A/DG130HA The Panel Controls Rear Panel Before making any connections, make sure that the power on the DG ampli- fier and any external devices is switched OFF. * The DG80-112A is shown in the illustration. !9 @0 @1 @3 @2 @4 @5 !8 OUT IN On the DG100-212A, you can connect the internal Mixer or additional amp speaker or, an external speaker to the amplifier. External Effector On the DG80-210A/DG80-112A, you can connect MIDI IN MIDI OUT the internal speaker or, an ext
Resumen del contenido incluido en la página 8
DG100-212A/DG80-210A/DG80-112A/DG130HA Connecting Speakers Before connecting speakers to the speaker jack(s) check the power rating and impedance of the speaker and make sure they meet or are within the requirements recommended for the equipment. For the DG100-212A Total Impedance The amplifier’s internal speaker (4 Ω ) is connected to the speaker jack. If it is necessary, you can disconnect the internal speaker and connect If two or more speakers are to be connected, you must take into an ext
Resumen del contenido incluido en la página 9
DG100-212A/DG80-210A/DG80-112A/DG130HA How to use your DG Series Amplifier To protect the speaker from possible damage, always set the OUTPUT knob to “0” before switching the power ON/OFF. First, achieve sound output Reverb Settings 1. With the DG amplifier’s power switched OFF, connect your gui- 1. Press the REVERB button to select a reverb type. Each time tar to the INPUT jack on the front panel. To start with, try using the REVERB button is pressed, the type will cycle through the LOW jac
Resumen del contenido incluido en la página 10
DG100-212A/DG80-210A/DG80-112A/DG130HA Recall and Store Preset setting data, specially created by Yamaha for the DG Series Amplifiers, is installed in memory numbers 1-80 when the amplifier is shipped from the factory. (Refer to the “Patch List” on page 83.) Setting data contains Amp Type and its settings (GAIN, MASTER, Tone Control, Reverb, Tremolo, Chorus and Tape Echo) that you can recall freely and use at any time. Motor drives in the knobs will automatically set the knobs to the correspondi
Resumen del contenido incluido en la página 11
DG100-212A/DG80-210A/DG80-112A/DG130HA Easy to Use Functions MIDI commands can be used to select memory numbers, control the reverb, tremolo, chorus and tape echo effects, and control volume on the DG amplifier. A speaker simulator can also be applied to the LINE OUT signal. What is MIDI? MIDI is the acronym for Musical Instruments Digital Interface. MIDI is a world-wide standard communication interface that allows MIDI compatible musical instruments, computers and other MIDI devices to share mu
Resumen del contenido incluido en la página 12
DG100-212A/DG80-210A/DG80-112A/DG130HA Utility Mode The Utility Mode is used to perform MIDI settings, set the speaker simulator and volume pedal position settings. To enter the Utility Mode, press and hold the button for more than one second, the “UTIL.” mode display lamp will light. Each of the settings will be stored in memory, even when the power to the amp is turned off. To exit from the Utility Mode, press the button, the “AMP” (amp mode) display lamp will light. * MIDI messages cannot
Resumen del contenido incluido en la página 13
DG100-212A/DG80-210A/DG80-112A/DG130HA Utility Mode Speaker Simulator ON/OFF MIDI Cable The DG amplifier’s speaker simulator provides the line signal with a realistic simulation of the natural sound of a speaker. The speaker simulator can be DG amplifier used on the line signal when the LINE OUT jack is connected to a mixer or Rear Panel MIDI OUT recorder. STATUS BANK MSB/MAX MIDI IN DATA/CTRL BANK LSB/MIN TOGGLE ON-OFF DEC INC MEMORY PC WRITE /NUMBER OF PGM 8.8.8. /NO ±10 /YES EDIT EDIT /EXIT
Resumen del contenido incluido en la página 14
DG100-212A/DG80-210A/DG80-112A/DG130HA Error Messages If an error occurs during operation, one of the following error message numbers will appear on the display. E1: Motor Drive Error CAUSE: The volume knob has not returned to its assigned position after 20 seconds has elapsed from the start of the recall operation or, the device does not recognize the recall command. SOLUTION: Turn off the power and return the device to the music dealer where you purchased it, or to the nearest Yamaha Service C
Resumen del contenido incluido en la página 15
DG100-212A/DG80-210A/DG80-112A/DG130HA Specifications Digital Section A/D Converter 20 bit Complete Digital Signal Processing D/A Converter 20 bit Internal 8 Channel Preset Digital Reverb (SPRING/HALL/PLATE) Sampling Frequency 48 kHz Digital Effects (Tremolo, Chorus, Tape Echo) Memory Number 128 Speaker Simulator (LINE OUT) Input Level/Impedance Analog Section INPUT HIGH: –30 dBm (THRU) / 1 MΩ DG100-212A : 100 W (4 Ω ) Solid State Power Amp INPUT LOW: –20 dBm (THRU) / 1 MΩ 30 cm Speaker (Celesti
Resumen del contenido incluido en la página 16
S412V/S112 Using the S412V/S112 The S412V is a speaker enclosure equipped with four Celestion “Vin- The S112 is a speaker enclosure equipped with a Celestion “G12H- tage 30” speakers. 100” speaker. * The power rating is 240 W. Use an amp head with a power * The power rating is 100 W. Use an amp head with a power output of less than 240 W. output of less than 100 W. * The impedance is 8Ω . Check the amp head’s impedance and * The impedance is 8Ω . Check the amp head’s impedance and make sure it m
Resumen del contenido incluido en la página 17
AMPLIFICATEUR DE GUITARE TÊTE D’AMPLIFICATEUR DE GUITARE ENCEINTE ACOUSTIQUE Mode d’emploi Nous vous remercions d’avoir fait l’acquisition d’un amplificateur de guitare de la série DG Yamaha. Les amplificateurs de guitare numériques de la série DG ont été conçus initialement et entièrement réalisés par Yamaha. Ces amplificateurs de guitare numériques délivrent des sons tout aussi puissants que ceux des amplificateurs à lampes tout en offrant une stabilité de fonctionnement supérieure compa- rée
Resumen del contenido incluido en la página 18
Table des matières DG100-212A/DG80-210A/DG80-112A/DG130HA Précautions d’usage .................................................. 18 Contrôle des effets de réverbération, trémolo, chœur et écho de bande par l’intermédiaire de MIDI .................... 24 Commandes en façade .............................................. 19 Simulateur de haut-parleur ........................................... 24 Façade .......................................................................... 19 Mo
Resumen del contenido incluido en la página 19
DG100-212A/DG80-210A/DG80-112A/DG130HA Commandes en façade * L’illustration ci-dessous représente le modèle DG100-212A. Façade q w e r t y u i o !0 !3 !4 !5 !7 !1 !2 !6 MASTER = 7, tous les potentiomètres de réglage de tonalité = 5). Le réglage du q Mini-prise d’entrée (INPUT HIGH, LOW) potentiomètre de réglage REVERB ne change pas. Raccordez la guitare à cette mini-prise. Les guitares à hauts niveaux de sortie doivent être raccordées à la mini-prise LOW. Les guitares à niveaux o Bouton de sél
Resumen del contenido incluido en la página 20
DG100-212A/DG80-210A/DG80-112A/DG130HA Commandes de la façade Face arrière Avant d’effectuer le moindre branchement, vérifiez que l’alimentation de l’amplifica- teur DG et de tous les appareils extérieurs a bien été coupée au préalable. !9 @0 * L’illustration ci-dessous représente le modèle DG80-112A. @1 @3 @2 @4 @5 !8 OUT IN Mixeur Avec le DG100-212A, vous pouvez raccorder le ou haut-parleur interne ou le haut-parleur externe à Effecteur extérieur amplificateur supplémentaire l’amplificateur.
