Résumé du contenu de la page N° 1
Model PRO9801C
Owner’s Manual
5 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override your security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand t
Résumé du contenu de la page N° 2
Protected Push Button LED Valet/Override Switch In Windshield Receiver 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming Intrusion Alert With Memory Instant Siren Activation When Used Starter Disable Output Additional Engine Immobilizer Output, (Optional Relay Required) True Last Door Arming (Hardwire Only) Defective Zone By-Pass Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared) Car Horn Output For Additional Alarm Response (Improved
Résumé du contenu de la page N° 3
known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system. Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then re-transmits your signal, the alarm system will not respond. If your transmitter button is pressed more than fifty times while it is out of range of the vehicle (for example, children playing with your keys), the transmitter
Résumé du contenu de la page N° 4
The dash mounted LED begins to flash slowly. Parking Lights flash one time. Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. Doors Lock - Optional NOTE: If the optional Headlamp illumination fe
Résumé du contenu de la page N° 5
Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle. DISARMING THE SYSTEM NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers
Résumé du contenu de la page N° 6
Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. Siren will not sound. If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered. Doors Unlock - Optional 2 Step Doors Unlock -
Résumé du contenu de la page N° 7
3. To return to normal operation, press and release the Push-Button switch any time the ignition is on. NOTE: Always remember to return the vehicle to the valet off position. This will ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: Using The Receiver's Push-Button Override Switch Your Security System can be disarmed without the use of the keychain transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter i
Résumé du contenu de la page N° 8
2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the Receivers Push-button switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 seconds, begin to press and release the Receivers Push-button switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5) 6. Within 10 seconds of the last press of the
Résumé du contenu de la page N° 9
NOTE: Your system must be programmed by the installation center to enable this feature. REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic: 1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for 3 seconds. If the button i
Résumé du contenu de la page N° 10
To change or adjust the shock sensor, press and release the ARM button of your keychain transmitter. 1. Within 2 seconds of arming, press and release the ARM button 1 time to defeat the pre-detect stage of the shock sensor. (The lights will flash and the siren will chirp once.) 2. Within 2 seconds of step 1, press and release the ARM button 2 times to defeat the pre and full detect stages of the shock sensor. (The lights will flash and the siren will chirp twice.) 3. Within 2 seconds of step 1,
Résumé du contenu de la page N° 11
lights will flash or turn on depending on the programming set up by your installation center. When you arrive at your vehicle, disarm the alarm system by pressing and releasing the arm/disarm button of your keychain transmitter. Enter the vehicle and turn the ignition key to the on position. NOTE: This system has the ability to be configured to a single press start if you so desire. Please check with your installation center if your system was changed from the default safe start setting of two p
Résumé du contenu de la page N° 12
The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. CANCELING THE AUTOMATIC START UP TIMER To cancel the automatic start up timer do one of the following: 1. Start the vehicle manually with the use of the ignition key and depress the brake pedal. 2. Remote start the vehicle using your keychain RF transmitter. NOTE: Option button used in combination is only available on the alternate remote transmitter and not available on the LCD Transmitt
Résumé du contenu de la page N° 13
ADDITIONAL REMOTE FUNCTION (CHANNEL 6 ) Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter, or by and independent button or combination of buttons. For your vehicle this output is: Controlled By: Trunk/Key Button Option Button Lock + Unlock Buttons Lock + Trunk/Key Buttons Unlock + Trunk/Key Buttons Other Transmitter button configurations are also available. Consult your installation center for other configurations not listed above that m
Résumé du contenu de la page N° 14
2. Set the parking, (hand), brake. 3. Be certain your foot is off the brake pedal. 4. Press the receiver's program/Push-Button switch 2 times within 5 seconds. The parking lights will flash two times indicating the mode was successfully entered. If your parking lights flashed four times, this indicates the turbo mode was on and is now turned off. With the turbo timer mode selected on, after you've arrived at your destination and while the engine is still running, set the parking brake, pause 2 s
Résumé du contenu de la page N° 15
NOTE: The engine can be started in many modes armed, disarmed, valet, etc... The screen shown is Locked/Armed and running. When the Panic Mode has been activated and the system is armed, the vehicle's lights will flash, the siren and lock icon will be displayed on the LCD screen and the siren will beep. If the system is disarmed and the Panic Mode is activated, the lights will flash, the unlock icon will be displayed, and the siren will beep on the LCD screen. Whenever the vehicle is operated fr
Résumé du contenu de la page N° 16
ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE: If the arm/disarm chirp tones have been turned off at the vehicle, when you arm, or disarm, the display will indicate this as shown and there will be no arm/disarm chirps at the transmitter. This is true if the transmitter is set for vibrate mode. When the vehicle is armed, and a door is opened, or ajar, the transmitter will chirp 3 times, the lights will flash, and the display will indicate a door trigger as shown on the previous page. When the door i
Résumé du contenu de la page N° 17
ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below: NOTE: The Transmitter must be within operating range of the vehicle, approximately 1000 ft. Check Vehicle Status: Press the lock+key+option buttons simultaneously for 1 second. The v
Résumé du contenu de la page N° 18
Note this feature must be activated at the vehicle at the prescribed time. Once activated at the vehicle, you can toggle the feature on by simultaneously pressing the Lock + Option buttons of the transmitter. The 24 hour icon will appear and the transmitter will emit a tone confirming the feature is active. NOTE: The unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide. NOTE:To insure accu
Résumé du contenu de la page N° 19
Battery Indicator: Your transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deterio- rates, the bars will disappear. 1 bar indicates the battery should be replaced. Replace battery with a fresh 1.5V AAA battery and dispose of the used battery properly. Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote: R
Résumé du contenu de la page N° 20
Temperature Start Mode. This icon will appear when the temp start mode is activated. The vehicle will start one time automatically when the temperature reaches 0*. Caution Be certain vehicle is outside before activating this mode. To toggle this feature on or off, from the Locked/Armed mode, press the Option and Lock buttons simultaneously. (Available on certain remote start models only). Throughout this manual you will find screen shots where they apply if using the two way transmitter. If usi
