DSC POWERSERIES PC1616の取扱説明書

デバイスDSC POWERSERIES PC1616の取扱説明書

デバイス: DSC POWERSERIES PC1616
カテゴリ: 家庭用防犯システム
メーカー: DSC
サイズ: 0.76 MB
追加した日付: 5/9/2013
ページ数: 16
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスDSC POWERSERIES PC1616の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、DSC POWERSERIES PC1616に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書DSC POWERSERIES PC1616をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書DSC POWERSERIES PC1616のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - DSC POWERSERIES PC1616の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
DSC POWERSERIES PC1616 取扱説明書 - Online PDF
Advertisement
« Page 1 of 16 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書DSC POWERSERIES PC1616を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書DSC POWERSERIES PC1616の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

PC1616/PC1832/PC1864 STANDARD INSTALLATION GUIDE
This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616,
PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual
which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com.
NOTE: All necessary information required to meet UL Listing requirements is contained

ページ2に含まれる内容の要旨

Hardware Installation Begin the installation by mounting the cabinet in a dry protected area with access to unswitched AC power. Install Hardware in the sequence indicated below. Do NOT apply power until installation is complete. NOTE: All wiring entry points are designated by arrows. All circuits are classified UL power limited except for the battery leads. Minimum 1/4” (6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and connections. 1. K

ページ3に含まれる内容の要旨

Hardware Installation (Cont.) North America Only POWER LIMITED Stand Off PC Board 1. Insert Stand off into cabinet mounting hole in the Cable Tie (not supplied) recommended desired location. Snap-in- place. Cabinet 2. Position circuit board mounting holes over UA503 DSC standoffs. Press firmly Primary:120VAC/60Hz. Secondary: 16.5VDC 40VA on board to snap-in-place. PC1616/1832/1864 DSCPTD 1640U Class II Transformer WARNING: NOTE: Do not connect High Voltage. Disconnect AC Power transformer to rec

ページ4に含まれる内容の要旨

Hardware Installation (Cont.) 4. AUX Power Wiring The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LED’s etc.… If the total current required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below. NOTE: Min/max operating voltages for devices, sensors and modules is 9.5VDC - 14VDC Refer to the list of Compatible Devices on the first page for the current draw of individual devices 5. PGM Wiring PGMs switch to

ページ5に含まれる内容の要旨

TESTING & TROUBLESHOOTING Testing:  Power up system  Program options as required (See Programming Section on reverse side) Note: For advanced programming refer to the PC1616/1832/1864 Reference manual  Violate, then restore zones  Verify correct Reporting Codes are sent to the Central Station Troubleshooting: LCD5500 LCD Programmable-Message Keypad Press [✱][2] to view a trouble condition.  The trouble light will flash and the LCD will display the first trouble condition present.  Use

ページ6に含まれる内容の要旨

Trouble Cause Troubleshooting Trouble [1] Service Required Press [1] to determine specific trouble [1] Low Battery Main panel battery less than 11 VDC NOTE: If battery is new allow 1 Hr. for battery to charge.  Verify voltage measured across AC terminals is NOTE: This trouble condition will not AC. Replace transformer if required. 16-18 V clear until the battery voltage is  Disconnect battery wire leads 12.5VDC min., under load.  Verify battery charging voltage measured across bat

ページ7に含まれる内容の要旨

Trouble Cause Troubleshooting Trouble [2] AC Failure No AC at panel AC input Verify voltage measured across AC terminals is 16-18VAC. terminals Replace transformer if required. Trouble [3] Telephone Line Trouble Phone Line Voltage at TIP, RING on  Measure the voltage across TIP and RING on the panel: DC DC (approx) main panel less than 3V  No phone off-hook – 50V  Any phone off-hook – 5VDC (approx)  Wire incoming line directly to TIP and RING.  If trouble clears, check wiring or the RJ-

ページ8に含まれる内容の要旨

Trouble Cause Troubleshooting Trouble [5] Zone Fault (Cont.) One or more wireless devices have  If the trouble occurs immediately, a conflict with a hard not checked in within the wired zone exists: programmed time  The zone being used is already assigned to a PC5108 zone expander  The zone being used is assigned as a keypad zone  Perform a Module Placement Test – Program Section [904] and verify the wireless device is in a good location.  If bad test results occur, test th

ページ9に含まれる内容の要旨

PROGRAMMING the required data. The Ready light will turn OFF and the Armed light How to Program: will turn ON. At any time the [#] can be pressed to exit any program section. All DSC recommends filling in the Programming Worksheet with the required changes made up to that point will be saved. programming information before programming the system. This will reduce the time required to program and will help eliminate errors. HEX (or hexadecimal) digits are sometimes required. To enter a HEX

ページ10に含まれる内容の要旨

[402] Downloading Computer Phone Number (32-digits) KEYPAD FUNCTION KEY DEFINITIONS 00 Null Key (Key not used) 17 [][0] Activate Stay/Away IDII___II___II___II___II___II___II___II___II___II___II___II___II___II___II___I 01 Partition 1 Select 18 Identified voice prompted 02 Partition 2 Select help I___II___II___II___II___II___II___II___II___II___II___II___II___II___II___II___I 03 Stay Arm 19 Command output 3 [73] 04 Away Arm 20 Not used [403] Downloading Access Code 05 [][9] No e

ページ11に含まれる内容の要旨

[005] System Times [013] – First System Option Code This section programs the entry and exit delays for the control panel. The first two toggle options in this section are used to determine what After entering section [005] press [1] to select partition 1. type of EOL resistors are being used, toggle option [1] to determine if Enter the 3-digit delay time for Delay 1 type zones, Delay 2 type zones normally-closed or EOL resistors are being used and option [2] to followed by the exit delay tim

ページ12に含まれる内容の要旨

[310]-[311] Partition Identifier Codes [380] – First Communicator Option Codes Enter a 6 digit Maintenance Code Opt Default Description [310 System Acct. Code I___II___II___II___II___II___I 1 I__I  ON Communications Enabled [311] Partition 1 Acct. Code I___II___II___II___I OFF Communications Disabled [350] – Communicator Format Options 2 I__I ON Restorals on Bell Time-out This section determines the communication format used for central station reporting. From the chart listed below program

ページ13に含まれる内容の要旨

LISTING REQUIREMENTS UL Listed Commercial and Residential Installations User Information The installer should advise the users and note in the User’s Manual: The installation requirements listed below must be met for the following grades of service. Service organization name and telephone number Grade AA Central Station and Police Connect (Standard or Encrypted Line The programmed exit time Security Service) The programmed entry time The installation must use T-Link module which communicate

ページ14に含まれる内容の要旨

PC1616/PC1832/PC1864 Installer Programming Quick Reference Chart SIA False Alarm Reduction SIA Feature Comments Range/Default Requirement Programming Section Exit Time Access to Entry and Exit delays for each partition and Bell Time Out for the system For Full or auto arming: Required [005], 3rd entry Range:45- 255 seconds (programmable) Default: 60 sec. Progress Annunciation/ Enables audible exit beeps from the keypad for the duration of exit delay Individual keypads Allowed Disable - for Silen

ページ15に含まれる内容の要旨

Note to Installers Limited Warranty This warning contains vital information. As the only individual in contact with system users, it is your respon- Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of sibility to bring each item in this warning to the attention of the users of this system. purchase, the product shall be free of defects in materials and workmanship under normal use. During the war- System Failures ranty period, Digital Sec

ページ16に含まれる内容の要旨

FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void Equipment Maintenance Facility your authority to use this equipment. If trouble is experienced with this equipment PC1616, PC1832, PC1864 for repair or warranty infor- This equipment has been tested and found to comply with the limits for a Class B digital device, pursu- mation, please contact the facility indicated below. If the equipment is causing harm to the telephone an


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 DSC , a Tyco International CompanyPC1832 取扱説明書 家庭用防犯システム 8
2 DSC , a Tyco International CompanyPC1616 取扱説明書 家庭用防犯システム 12
3 DSC , a Tyco International CompanyPowerSeries 取扱説明書 家庭用防犯システム 2
4 DSC POWERSERIES PC1832 取扱説明書 家庭用防犯システム 45
5 DSC POWERSERIES PC1864 取扱説明書 家庭用防犯システム 26
6 DSC WLS900 取扱説明書 家庭用防犯システム 0
7 DSC , a Tyco International CompanyPC1864 取扱説明書 家庭用防犯システム 12
8 3Com 1000BASE-T-GBIC 取扱説明書 家庭用防犯システム 0
9 Sony BRCSDP12 取扱説明書 家庭用防犯システム 3
10 3Com TECHD-0000000122 取扱説明書 家庭用防犯システム 1
11 Sony SSC-M354 取扱説明書 家庭用防犯システム 3
12 Sony DIGITAL 8 DCR-TRV130E 取扱説明書 家庭用防犯システム 9
13 Sony SNC-RX SNC-CS50 取扱説明書 家庭用防犯システム 4
14 Sony SSC-M183/M183CE/M188CE SSC-M383/M383CE/M388CE 取扱説明書 家庭用防犯システム 10
15 Sony CD-7226 取扱説明書 家庭用防犯システム 1