ページ1に含まれる内容の要旨
Owner's
Manual
WARNING
Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Page Page Safety Instructions 2 Conditioning Guidelines 15 Before You Begin 4 Warm-up and Cool-Down 16 Hardware Identification Chart 5 Warranty 17 Assembly Instructions 6 Product Parts Drawing 18 Set Up Instructions 11 Parts List 19 Operational Instructions 12 Notes 21 Storage 14 Fax/Mail Ordering Form 22 Maintenance 14 SAFETY INSTRUCTIONS WARNING: To reduce the risk of serious injury, read the following Safety Instructions before using the SpaceMate E300 Dual-Acti
ページ3に含まれる内容の要旨
CALL US FIRST THANK YOU FOR PURCHASING THE SpaceMate E300 Dual-Action Elliptical Trainer To help you get started, we have pre-assembled most of your SpaceMate E300 at the factory with the exception of those few parts left unassembled for shipping purposes. Simply follow the few assembly instructions set forth in this manual. With regular workouts you will be getting your body into shape and on your way to achieving a happier and healthier lifestyle. Should you have any questions, please call our
ページ4に含まれる内容の要旨
BEFORE YOU BEGIN Thank you for choosing the SpaceMate E300. We Although Stamina constructs its products with the take great pride in producing this quality product and finest materials and uses the highest standards of hope it will provide many hours of quality exercise to manufacturing and quality control, there can make you feel better, look better and enjoy life to its sometimes be missing parts or incorrectly sized fullest. parts. If you have any questions or problems with Yes, it's a
ページ5に含まれる内容の要旨
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of the bolts, or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES 02 1/2 1 1/2 1/2 3 1/2 4 1/2 5 1/2 6 in. mm. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 length MILLIMETERS 6 8 10 12 NOTICE: The length of all bolts and screws except those with
ページ6に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part please call our toll-free number for assistance 1 (800) 375-7520 or e-mail us at: parts@staminaproducts.com BACK FRONT STEP 1 Attach the FRONT STABILIZER(2) onto the
ページ7に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS L L R R STEP 4 1. There is an "L" decal on the LEFT PEDAL ARM(4), and an "R" decal on the RIGHT PEDAL NOTE: ARM(5). 2. The RIGHT PEDAL SHAFT(34) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL SHAFT(33) has left hand threads and is tightened by turning counter clockwise. Place the front end of the RIGHT PEDAL ARM(5) on the ROLLER(39). Connect the back end of the RIGHT PEDAL ARM(5) to the RIGHT CRANK(31) located inside the CRANK DISK(28) as shown
ページ8に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS Metal Fitting Cable End Strap Bracket Spring Hook Strap STEP 6: Refer to the illustration. Slide the CABLE on the TENSION KNOB(21) through the UPRIGHT(6). Attach the TENSION KNOB(21) onto the UPRIGHT(6) with FLAT HEAD SCREW(M5x0.8x15mm)(59). STEP 7: Refer to the inset drawing. Lay the UPRIGHT(6) on the floor close to the front of the MAIN FRAME(1). Turn the TENSION KNOB(21) on the UPRIGHT(6) counterclockwise as far as it can go, so the cable end extends out of the metal f
ページ9に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS Look down from the top STEP 10 Attach the LINKAGES(80) to the LEFT and RIGHT PEDAL ARMS(4, 5) at both sides with the PLASTIC WASHERS(M8)(69), BUTTON HEAD BOLTS(M8x1.25x18mm)(75), WASHERS(M8)(70) and NYLOCK NUTS(M8x1.25)(62). STEP 11 Look down from the top of the UPRIGHT(6) to make sure the pivot tubes on the PIVOT ARMS(79) are parallel to the FRONT STABILIZER(2) and the PEDAL ARMS(4, 5) are crossing the ROLLERS(39) properly. Tighten the BUTTON HEAD BOLTS(M8x1.25x57mm)(49) o
ページ10に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS L R STEP 12 There is an "L" decal on the LEFT HANDLEBAR(81), and an "R" decal on the RIGHT HANDLEBAR(82). Attach the LEFT and RIGHT HANDLEBARS(81, 82) onto the PIVOTING ARMS(79) with HEX BOLTS (M6 x 35mm)(74), ARC WASHERS(M6)(71), LOCK WASHERS(M6)(72), and ACORN NUTS(M6)(73). STEP 13 Lubricate the HANDLEBARS(81, 82) with a small amount of liquid soap, then slide the two FOAM GRIPS(83) onto the HANDLEBARS(81, 82). STEP 14 Install an AAA battery into the METER(22). See page 1
ページ11に含まれる内容の要旨
SET UP INSTRUCTIONS Place the SpaceMate E300 in the area where it will be used. It is recommended that the SpaceMate E300 be placed on an equipment mat. The maximum operation dimensions of the SpaceMate E300 are approximately 34 3/4" long x 23 1/8" wide x 54 3/8" tall. (These dimensions may vary up to one inch.) An area 4 feet wide x 5.5 feet long is required for safe operation of the SpaceMate E300. Make sure that adequate space is available for access to and passage around the SpaceMate E300.
ページ12に含まれる内容の要旨
OPERATIONAL INSTRUCTIONS USING THE ELECTRONIC METER Pedal movement or press the button. POWER ON: Automatic shut off after four minutes of inactivity. POWER OFF: FUNCTION BUTTON: MODE : Press and release to select functions. Press and hold for three seconds to reset all functions to zero. FUNCTIONS: SCAN: Automatically scans TIME, SPEED, DISTANCE, and CALORIES in sequence with a change every four seconds. Press and release the button until "SCAN" appears on the display. TIME: Displays the time
ページ13に含まれる内容の要旨
OPERATIONAL INSTRUCTIONS LOAD ADJUSTMENT To increase the load, turn the TENSION KNOB(21) clockwise. To decrease the load, turn the TENSION KNOB(21) counterclockwise. EXERCISE WORKOUT To start using the SpaceMate E300 simply stand on the foot pedals with the fronts of your shoes close to the front edge of the pedal cap. Place your hands at a comfortable position on the handlebars. Simply move your highest foot forward and follow the natural path of the machine. Start on a load level that is comf
ページ14に含まれる内容の要旨
STORAGE 1. To store the SpaceMate E300 simply keep it in a clean dry place. 2. The minimum rest dimensions of the SpaceMate E300 are approximately 32 1/2" long x 23 1/8" wide x 54 3/8" tall. These dimensions may vary. Please measure your SpaceMate E300 if exact dimensions are needed. 3. Grasp the pivot tubes on the HANDLEBARS(81, 82) and REAR STABILIZER(3) to move the SpaceMate E300, two people are required for moving. Do not use the Pedal Arms to move the SpaceMate E300. 4. To avoid damage to t
ページ15に含まれる内容の要旨
CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive for several years or are severely overweight, start slowly and increase your workout time gradually. Increase your workout intensity gradually, too, by monitoring your heart rate while you exercise. Remember to follow these essentials: Have your doctor review your training and diet programs. Begin your training program slowly with realistic goals that have been set by you and
ページ16に含まれる内容の要旨
WARM-UP and COOL-DOWN Warm-up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength-training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging, jumping jacks, jump rope, and running in place Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength or aerobic training se
ページ17に含まれる内容の要旨
LIMITED WARRANTY MODEL 55-1630 WARRANTY Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and one year on the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAI
ページ18に含まれる内容の要旨
PRODUCT PARTS DRAWING FRONT Strap Strap BACK 18
ページ19に含まれる内容の要旨
PARTS LIST DIAGRAM# PART NAME QTY 1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Left Pedal Arm 1 5 Right Pedal Arm 1 6 Upright 1 7 Pulley and Axle 1 8 Bearing (6003Z) 2 9 Bearing Washer (M17) 1 10 C Ring (17mm) 1 11 V Belt 1 12 Flywheel 1 13 Bearing (6900Z) 2 14 Flywheel Axle 1 15 Eyebolt 2 16 Tension Bracket 2 17 Tension Spring 1 18 Tension Strap 1 19 Buckle 1 20 Tension Cable 1 21 Tension Knob 1 22 Meter 1
ページ20に含まれる内容の要旨
PARTS LIST DIAGRAM# PART NAME QTY 48 Bolt, Button Head (M8 x 1.25 x 20mm) 4 49 Bolt, Button Head (M8 x 1.25 x 57mm) 2 50 Bolt, Button Head (M8 x 1.25 x 60mm) 4 51 Bolt, Button Head (M10 x 1.5 x 50mm) 2 52 Bolt, Round Head (M6 x 1 x 43mm) 4 53 Screw, Round Head (M4 x 12mm) 2 54 Screw, Round Head (M4 x 15mm) 4 55 Screw, Round Head (M4 x 25mm) 4 56 Screw, Round Head (M5 x 15mm) 4 57 Screw, Round Head (M5 x 15mm) 1 58 Screw, Flat Head (M5 x 15mm) 1 59 Screw, Flat H