Summary of the content on the page No. 1
uni ~n@
XC 320
Cordless Telephone
Operating Guide
For Australia and New Zealand
Summary of the content on the page No. 2
Table of Contents ImportantSafetyInstructions 3 Aboutyour XC 320 5 Unpacking 5 XC 320 Features """"""""""""""""""""""""""" 6 Automatic Digital Code Security. 6 Base Unit Controls & Functions 7 Handset Controls & Functions 9 Read This Before Installation 11 Installing Your XC 320 11 Connecting the Telephone Line 11 Installing the Telephone on a Desk or Tabletop 12 Mounting the Telephone on a Wall 12 Connecting the AC Power 13 Installing the Battery Pack (BT-161) 13 Charging the Battery Pack 14 Lo
Summary of the content on the page No. 3
PRECAUTIONS Beforeyou read anythingelse, please observe the following: WARNING! Uniden Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. NICKEL-CADMIUM BATTERY WARNING . This equipment contains a Nickel-Cadmium Battery. . The Nickel-Cadmium Battery contained in this equipment may explode if disposed of in a fire. . Do not short circuit the battery. . Do not charge the Nickel
Summary of the content on the page No. 4
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. 4. Do not use this product near water; for ex
Summary of the content on the page No. 5
12.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. If the power supply cord is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage,
Summary of the content on the page No. 6
About Your XC 320 Congratulations on your purchase of the Uniden XC 320 Cordless Telephone. The XC 320 is designed and engineered to exacting standards for reliability, long life, and outstanding performance. To get the most from your XC 320, please read this Operating Guide thoroughly. Unpacking Yourxc 320 boxshouldcontainthefollowingitems: . BaseUnit . Handset . Telephone Line Cord with Modular Plug . AC Adapter . Rechargeable BatteryPack . This Operating Guide (read thoroughly) . Memory Stora
Summary of the content on the page No. 7
XC 320 Featu res . UltraClear Plus noise reduction provides the quality sound of a corded telephone. . Eight 30/39 MHz Channels (Australia): Three 30/39 MHz Channels (New Zealand) . 20-Number Memory . Maximum Operating Range . One-Touch Memory Dialing . 2-Way Paging/Intercom . Redial/Pause and Flash . AutoStandby . AutoTalk . Tone/Pulse Dialing (available on Australian Models only) . Automatic Digital Code Security . Handset Volume Control/Ringer Volume Control . Battery Saving Feature . 2-Way H
Summary of the content on the page No. 8
Base Unit Controls & Functions RING- OFF LO HI Switch TELLINE TONEPULSE DCIN9V +%- Switch ~ HandsetRetainer INUSELED I BASEUNIT Antenna I Speaker I8B1 ........... ........... ........... ........... ........... ........... ........... ........... ........... 0 0 .. . ~ . f= CHARGE LED Microphone PAGEIINT'COM Button 7
Summary of the content on the page No. 9
Base Unit Use to set the ring volume level ("LO" or "HI") of the Ringer Switch Base Unit for incoming calls, or the page alert tone level when paged from the Handset. TONE/PULSE Use to select either Tone Dialing or Pulse Dialing. Switch (Available on Australian Models only) TEL LINE Jack Plug the supplied telephone line cord into this jack and the other end of the cord into the standard modular telephone socket. DC Input Jack Plug the AC Adapter cord into this jack. Then plug the AC Adapter into
Summary of the content on the page No. 10
Handset Controls &Functions Handset Antenna CHANNEL Button AINGON BA TT SAVE Switch 1- 9, 0, TONE*, # Button ONE-TOUCH DIAL ~ -J;, -~ ~ ~..' MEMButton Buttons INT'C Button ~-~if ~ RDUP Button FLASH/A. TONE K -rl- A VOLUME/A. VOL Button Button Handset Antenna Flexible antenna. TALK/BA TT This LED has a dual function: (a) When the phone is in LOWLED use, the red LED lights steady. (b) When the battery pack is Iow and need to be recharged, the LED flashes every 3 seconds. TALK Button Press to place
Summary of the content on the page No. 11
Numeric Keys Use for dialing numbers and storing numbers in memory. ONE-TOUCH DIAL Special memory locations for storing numbers. Press Buttons the appropriate button to dial a number. INT'C Button Use to page the Base Unit and establish communication between the Handset and the Base Unit. When you press this button, 3 beep tones sounds repetitively at the Base Unit and Handset until the page is answered. (Note: The Page/Intercom feature does not work if the BASEUNITRINGER switch is in the "OFF"p
Summary of the content on the page No. 12
Installing the Telephone on a Desk or Tabletop Place the Base Unit on a desk or tabletop, and plug one end of the Telephone Line Cord (supplied) into the "TELLINE" jack on the Base. Plug the other end of the cord into the telephone socket. The unique design of your XC 320 allows you to place the Handset on the Base Unit either facedown or in an upright position. The battery pack in the Handset automatically recharges in either position. Mounting the Telephone on a Wall Setting the Handset Retain
Summary of the content on the page No. 13
Read This Before Installation We have designed your telephone to conform to Australia or New Zealand Radio Frequency regulations, and you can connect it to most telephone lines. However, each device that you connect draws power from the phone line. We refer to the power drawn as the devices ringer equivalence number or REN. The REN is shown on the bottom of your telephone (New Zealand Models only). If you are using more than one phone or other device on the line, add up all the REN's. If the tot
Summary of the content on the page No. 14
If you are mounting the XC 320 on an existing standard wall plate: 1. Plug one end of the Telephone Line Cord (supplied) into the "TELLINE" jack on the top of the Base Unit. Lay the cord inside the molding on the bottom of the Base Unit. Then plug the other end of the cord into the telephone wall socket. 2. Mount the Base Unit onto the wall plate. Then hang the Handset on the cradle. If you are mounting the XC 320 elsewhere: 1. Carefully select a location away from electrical cables, pipes, or o
Summary of the content on the page No. 15
1. Remove the battery compartment cover on the Handset by sliding it down. ... 2. Connect the Nickel-Cadmium Battery Pack by plugging it into the socket at the top of the battery compartment. Note: The connector fits only one way and requires only a minimal amount of pressure to insert. Always install the Battery Cable with the BLACK wire to the left. 3. Place the Battery Pack inside the t compartment and slide the battery cover back on. Make sure not to get the wires from the Battery Pack caugh
Summary of the content on the page No. 16
Low Battery Indicator When the Battery Pack in the Handset is very Iow and needs to be charged, the TALKlBATT LOWLED flashes every 3 seconds. If this occurs while you are on the phone, a short alert beep will also sound. When this happens, complete your call as quickly as possible, and return the Handset to the Base Unit for charging. Allow 12 to 16 hours for Handset to recharge. When the battery is Iow, only the TALKbutton will function. Using Your XC 320 Selecting Pulse or Tone Dialing (availa
Summary of the content on the page No. 17
Setting the Base Unit Ringer Volume To enable the Base Unit to ring when an incoming call is received, or when a page is sent from the Handset, set the BASEUNITRINGER switch to either "LO" or "HI". Placing a Call To place a call with your XC 320: 1. Remove the Handset from the Base Unit and press TALK. 2. Dial the number you are calling. 3. When you have finished the call, press TALKor return the Handset to the Base Unit. NOTE: If you don't place the Handset back on the Base Unit, you will need
Summary of the content on the page No. 18
Using the Redial Button RDLlPdials the last number that you called. This feature is extremely useful when the number you called is busy. To use this feature, simply press FLASH, then RDLlP. The last number called will then be dialed again. NOTE: If any other key is pressed before RDLlP,the phone will not redial the last number. Answeri ng a Call Your XC 320 will ring when someone is calling your number. If your Handset is not in the Base Unit, press TALKto answer the call. If your Handset is in
Summary of the content on the page No. 19
NOTE: You have 20 seconds after pressing MEM to enter the number you wish to store. Otherwise, an error tone will sound. 5. Write the stored number and its memory location number on one of the enclosed stickers so you won't forget them. Storing a Mixed Tone/Pulse Number With a Pulse Dial System (available on Australian Models only) If you've set up your XC 320 for Pulse Oialing, you can store a mixed mode number to make it easy to access long distance services. To store a mixed mode number (up t
Summary of the content on the page No. 20
NOTE: Youcanalsostorea mixedtone-pulse number in a ONE-TOUCH DIALlNG button. To do this, follow steps 2 through 5 in "Storing a Mixed Tone/Pulse Number". 4. Press MEM,and the ONE-TOUCH DIALlNG button (1,2,or 3) you wish to program. You will hear a long beep when the number you have entered has been successfully stored. NOTE: You have 20 seconds after pressing MEMto enter the number you wish to store. Otherwise, an error tone will sound. 5. Write the stored-number and its ONE-TOUCH DIALlNGbutton
