Summary of the content on the page No. 1
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 1
THE
RANGE
USER MANUAL
Di5, Di5t,
Di5 DC & Di5 DCt
Di6, Di6t,
Di6 DC & Di6 DCt
Di8 DC & Di8 DCt
Summary of the content on the page No. 2
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 2 3 INTRODUCTION 3 SAFETY INSTRUCTIONS 4 PRODUCT IDENTIFICATION 5 STANDARD AND OPTIONAL ACCESSORIES 6-9 INSTALLATION GUIDELINES 6 Installation using supplied yoke bracket TM 7 Installation using optional K-Ball bracket 8 Installation using supplied yoke bracket with optional pole-mount adaptor TM 9 Installation using optional K-Ball bracket with optional pole-mount adaptor 10 PRODUCT DIMENSIONS 11 HARDWARE DIMENSIONS 12-13 TECHNICAL SPECIFICATIO
Summary of the content on the page No. 3
RANGE THE USER MANUAL Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 3 Designed for a wide variety of sound reinforcement applications the Tannoy Di is an ultra compact loudspeaker system capable of delivering high sound pressure levels with extremely low distortion, resulting in outstanding clarity, definition and detail. A truly universal solution, the Di offers outstanding durability and resistance to scuffs and knocks. Able to deliver consistent performance under a wide range of adverse
Summary of the content on the page No. 4
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:51 Page 4 YOKE TRIM Remove the yoke trims on the top and bottom panels to access the yoke bracket fixing point GRILLE TRIM Lift the grille trim back using the tab to access the transformer tapping switch on transformer models. GRILLE INPUT CONNECTOR Remove the rubber grommet to access the connector. The rubber grommet ensures the rear of the product is kept water-tight SAFETY TAB 4
Summary of the content on the page No. 5
RANGE THE USER MANUAL Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 5 GRILLE GRILLE TRIM YOKE BRACKET (SUPPLIED WITH FIXINGS) POLE MOUNT ADAPTOR TM K-BALL BRACKET 5
Summary of the content on the page No. 6
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 6 USING SUPPLIED YOKE BRACKET 1. Fix the yoke bracket 2. Remove the yoke 3. Remove the rubber 4. Feed the speaker to the surface using a trims from the product grommet from the rear of cable through the rubber suitable fixing method. to access the bracket the speaker. Inclusion of grommet then connect fixing points. the rubber grommet is the euro-type plug to the only required if installing wires, observing the the product outdoors. correct pola
Summary of the content on the page No. 7
RANGE THE USER MANUAL Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 7 TM USING OPTIONAL K-BALL BRACKET 1. If attaching the 2. Connect the speaker 3. If a conduit junction 4. If you are attaching TM K-Ball bracket to a wires to the connector box has been used, the bracket directly to a flush mounted inwall block in the bracket. offer the bracket up to surface, offer the conduit junction box For connection to an the adaptor plate, with bracket up to the (J-box), pass the amplifier use pins 1
Summary of the content on the page No. 8
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 8 IUSING OPTIONAL POLE MOUNT ADAPTOR IWITH SUPPLIED YOKE BRACKET 1. Use the supplied 2. Fix the pole mount 3. Remove the yoke 4. Remove the rubber fixings to fix the yoke bracket adaptor to the trims from the product grommet from the rear bracket to the pole pole using the strapping to access the bracket of the speake. Inclusion bracket adaptor. provided. The bracket fixing points. of the rubber grommet is can be mounted in only required if i
Summary of the content on the page No. 9
RANGE THE USER MANUAL Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 9 USING POLE MOUNT ADAPTOR TM WITH OPTIONAL K-BALL BRACKET TM 1. Pass the speaker wire 2. Connect the speaker 3. Offer the K-Ball 4. Fix the pole mount through the pole-mount wires to the connector bracket up to the bracket adaptor to the adaptor plate then fix the block in the rear of the adaptor plate, with the pole using the strapping TM pole mount bracket K-Ball bracket. foam gasket** provided. The bracket adaptor
Summary of the content on the page No. 10
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 10 Di5 Di6 Di8 10
Summary of the content on the page No. 11
RANGE THE USER MANUAL Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 11 5” YOKE BRACKET 241.0 R15.0 85.0 90.0 [9.49"] [R0.59"] [3.35"] [3.54"] 123.0 [4.84"] 6.0 [0.24"] 35.0 ?22.0 [1.38"] [?0.87"] 54.0 [2.13"] 6” YOKE BRACKET R15.0 [R0.59"] [2.56"] 358.0 [14.09"] 145.0 150.0 [5.71"] [5.91"] 180.0 [7.09"] 35.0 ?22.0 6.0 [1.38"] [?0.87"] [0.24"] 65.0 [2.56"] Di6 YOKE Di6 YOKE 8” YOKE BRACKET 406.0 [15.98"] R15.0 Di6 YOKE [R0.59"] Di6 YOKE 165.0 170.0 [6.50"] [6.69"] 217.0 [8.5
Summary of the content on the page No. 12
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 12 TM ICT MODELS Di5 Di6 SYSTEM (1) Frequency Response (-3dB) 90Hz - 25kHz 75Hz - 22kHz (1) Frequency Range (-10dB) 80Hz - 30kHz 55Hz - 24kHz (2) System Sensitivity (1W @1m) 88dB 90dB 1W = 2.45V for 6 Ohms Dispersion 90 90 Degrees conical -6dB Low Frequency Driver 1x 110mm (4.50”) 1x 165mm (6.50”) Mineral loaded polypropylene TM TM High Frequency Driver ICT ICT Crossover 7kHz 7kHz Inductively Coupled ICT™ Directivity Factor (Q) 1kHz to 10kHz 5
Summary of the content on the page No. 13
RANGE THE USER MANUAL Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 13 TM DUAL CONCENTRIC MODELS Di5 DC Di6 DC Di8 DC SYSTEM (1) Frequency Response (-3dB) 90Hz - 50kHz 75Hz - 30kHz 65Hz - 30kHz (1) Frequency Range (-10dB) 80Hz - 54kHz 55Hz - 35kHz 53Hz - 35kHz (2) System Sensitivity (1W @1m) 88dB 89dB 91dB 1W = 2.83V for 8 Ohms Dispersion 90 90 90 Degrees conical -6dB Low Frequency Driver 1x 110mm (4.50”) 1x 165mm (6.50”) 1x 200mm (8.00”) TM Dual Concentric constant directivity driver wit
Summary of the content on the page No. 14
Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 14 All Di products can be custom painted. If you choose to paint your product, the entire product should be spray painted with the grille and grille trim still attached to the cabinet. Flexible vinyl paint should be used and care must be taken not to over apply paint, especially to the grille. No maintenance of the Di loudspeaker is necessary. All of our products have been produced and tested with care and precision to give first-class service.
Summary of the content on the page No. 15
RANGE THE USER MANUAL Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 15 The following apparatus is manufactured in China for Tannoy Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecomm
Summary of the content on the page No. 16
REVISION DATE: 19 Feb ‘07 6481 0471 02/06 Di Manual 8-2-07 AW:Layout 1 21/2/07 10:52 Page 16 Tannoy United Kingdom T: 00 44 (0) 1236 420199 E: enquiries@tannoy.com Tannoy North America T: 00 1 (519) 745 1158 E: inquiries@tannoyna.com Tannoy Deutschland T: 00 49 (180) 1111 881 E: info@tannoy.com Tannoy France T: 00 33 (0)1 7036 7473 E: ventes@tannoy.com Tannoy adopts a policy of continuous improvement and product specification is subject to change.