Summary of the content on the page No. 1
Commercial Treadmill Owner’s Manual
C932
COMMERCIAL PRODUCTS DIVISION
Summary of the content on the page No. 2
COMMERCIAL PRODUCTS DIVISION IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be taken, including the following: To ensure your safety and to protect the unit, read all the instructions before as- sembling and using the treadmill. To ensure the proper use and safety of the treadmill, make sure that all users read this manual. Please make this manual a part of your club’s training program. Remind the club users that before beginning any fitness
Summary of the content on the page No. 3
COMMERCIAL PRODUCTS DIVISION IMPORTANT SAFETY INSTRUCTIONS Never step off the treadmill while the running belt is moving. Keep your body and head facing forward. Never attempt to turn around on the treadmill. Never turn ON the treadmill when someone is standing on the machine. Never block the air openings on the hood while operating the treadmill. Keep the air openings clean and free of lint, hair, or anything that might impeded the free flow of air. Never drop or insert objects into any o
Summary of the content on the page No. 4
COMMERCIAL PRODUCTS DIVISION Table of Contents Important Safety Instructions .........................................2 Safety Approval...................................................................... 3 Grounding Instructions........................................................... 3 Radio Frequency Interference (RFI)....................................... 6 European Applications ........................................................... 6 Obtaining Service ..............................
Summary of the content on the page No. 5
COMMERCIAL PRODUCTS DIVISION Table of Contents The C932 Keypad ...........................................................30 Keypad Tips ........................................................................... 30 Special Keypad Functions at the Precor Banner .................... 30 Keys on the Keypad ............................................................... 32 Changing the Display Features Using the SELECT Key ........ 34 Exercising on the C932 ..........................................
Summary of the content on the page No. 6
COMMERCIAL PRODUCTS DIVISION RADIO FREQUENCY INTERFERENCE (RFI) Federal Communications Commission Part 15 The treadmill has been tested and found to comply with: The IEC EMC Directive (international electromagnetic compatibility certification) The limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. The treadmill generates, uses, and can radiate radio fr
Summary of the content on the page No. 7
COMMERCIAL PRODUCTS DIVISION OBTAINING SERVICE Do not attempt to service the treadmill yourself except for the maintenance tasks described in this manual. The treadmill does not contain any user-serviceable parts. For information about product operation or service, visit the Precor Web Site at www.precor.com or contact an authorized Precor Commercial Products Customer Support Representative at 1-888-665-4404. To help customer support personnel expedite your call, have your serial number availabl
Summary of the content on the page No. 8
COMMERCIAL PRODUCTS DIVISION Unpacking the Treadmill Thank you for purchasing the Precor C932 treadmill. Built to the exacting stan- dards of the health club environment, the treadmill is intended for commercial use and can withstand the rigors of daily club use with little maintenance. Important: Before using the treadmill, we urge you to familiarize yourself and your staff with the entire Owner’s Manual. Understanding this manual will help you and your customers use the treadmill safely and su
Summary of the content on the page No. 9
COMMERCIAL PRODUCTS DIVISION Hardware kit. Diagram 2 AC E G B D F H Carefully unpack the pieces of the treadmill and lay them on the floor near the location where you plan to use the treadmill. HARDWARE KIT After unpacking the treadmill, open the hardware kit (refer to Diagram 2) and make sure that you have the following items: ❑ (A) four 2-inch long socket head screws — mount upright supports to base ❑ (B) four barrel spacers — place on 2-inch screws ❑ (C) ten ¾-inch long socket head screws ❑ (
Summary of the content on the page No. 10
COMMERCIAL PRODUCTS DIVISION Setting Up the Treadmill You do not need any special knowledge or experience to set up the treadmill. However, you will need assistance during assembly. INSTALLATION REQUIREMENTS Follow these installation requirements when installing the treadmill. If you do not install the treadmill according to the following guidelines, you could void the Precor limited warranty. Set up the treadmill on a solid, flat surface. Unpack and assemble the treadmill close to where you
Summary of the content on the page No. 11
COMMERCIAL PRODUCTS DIVISION CAUTION: Do not lift the rear end of the treadmill by grasping the rear roller or the end cap. The running belt can move and the end caps can break off which may cause injury to you or to the unit. 3. Move the treadmill. Diagram 3. To avoid injury to yourself or damage to the unit, ask for help in placing the treadmill where you plan to use it. Diagram 3 illustrates how to properly lift the rear end so that you can roll it on its front wheels. Diagram 4 Remove the s
Summary of the content on the page No. 12
COMMERCIAL PRODUCTS DIVISION Diagram 5 Route the cable. Display cable Right side mounting bracket Route cable through hole. Right side upright support CAUTION: To avoid damage to the display cable, read and follow these steps carefully. Damage to the cable due to improper assembly is not covered by the Precor limited warranty. 6. Route the display cable. Diagram 5. Unwrap the cable and remove any kinks. Have an assistant hold the right upright support close to the base while you route the cable
Summary of the content on the page No. 13
COMMERCIAL PRODUCTS DIVISION a. Place a washer (D) onto each of two ¾-inch screws (C). Thread the screws through the front panel and into the upright support. See Diagram 6, #2. Do not fully tighten the screws. Leave room for final adjustments. CAUTION: Avoid pinching the cable with the bolts and spacers. b. Place a washer (D) and barrel spacer (B) on each of two 2-inch screws (A). Insert the screws through the upright support and thread them into the base mounts. See Diagram 6, #3. Do not secu
Summary of the content on the page No. 14
COMMERCIAL PRODUCTS DIVISION Diagram 8 Connect the cable. 1 2 Cable connector Cable receptacle Display console 4 3 Mounting holes Tie wrap Upright support Cable connector 10. Connect the display cable and secure the display console. Refer to Diagram 8, #1 and take the following steps to secure the display cable and console. a. Attach the cable connector by sliding it into its receptacle underneath the console. A definite “click” is heard when the cable is properly attached. Refer to Diagram 8, #
Summary of the content on the page No. 15
COMMERCIAL PRODUCTS DIVISION 11. Install the center handrail. Loosen the four fasteners in the handrail clamp bracket with the hex key provided. See Diagram 9, #1. The center handrail is packaged in two pieces. Install one side at a time by following these steps: a. Insert a handrail end cap. See Diagram 9, #2. b. Slide the end of the handrail into the center clamp and rotate the handrail so that it falls inside the end cap. See Diagram 9, #3. Diagram 10 Secure the display 2 console and center h
Summary of the content on the page No. 16
COMMERCIAL PRODUCTS DIVISION Diagram 11 Secure the upper handrail clamp. Handrail clamp Washer (F) with 1½-inch screw (E) Tighten the screws, but leave room for adjustments. 12. Install fasteners in the handrail clamp. Diagram 11. Return to the center handrail clamp and place a large washer (F) onto each of two screws (E). Thread the screws through the handrail clamp. Finger tighten. CAUTION: Do not overtighten the screws or you may inadvertently cause stress cracks. Diagram 12 Secure the fasten
Summary of the content on the page No. 17
COMMERCIAL PRODUCTS DIVISION Diagram 13 Tighten the handrail 2 1 fasteners. Handrail end cap Center handrail clamp screws (2) 3 Center console bracket screws (4) 14. Tighten all the center handrail fasteners. Diagram 13. Start with tightening the two end cap screws and work inward. See Diagram 13, #1. So that you don’t overtighten the fasteners, hold the supplied hex key by its 3-inch section and tighten the two center clamp screws. Refer to Diagram 13, #2. Next, tighten the four console bracket
Summary of the content on the page No. 18
COMMERCIAL PRODUCTS DIVISION Diagram 15 Connect to power outlet. On/Off switch 2 Power plug 17. Plug the power cord into an appropriate power outlet. Refer to Ground- ing Instructions on page 3. Make sure that the ON/OFF (I/O) power switch, located on the front panel of the treadmill, is placed in the OFF (O) position. CAUTION: The treadmill requires a dedicated, grounded circuit. A 20 amp circuit is recommended. Make sure that no other product or machine uses the same circuit as the treadmill.
Summary of the content on the page No. 19
COMMERCIAL PRODUCTS DIVISION CHECKING THE ALIGNMENT OF THE RUNNING BELT The belt is aligned at the factory before shipment. However, during shipment or by using the treadmill on an uneven surface, the belt might move off center. Proper belt alignment is important because it allows the belt to remain centered and assures smooth operation. Follow these steps to check the alignment: CAUTION: Do not walk on the running belt during this procedure. 1. The treadmill has adjustable rear feet. Check to m
Summary of the content on the page No. 20
COMMERCIAL PRODUCTS DIVISION Club Information These next few pages provide information that lets you customize the treadmill for your Club. It is not information that your customer needs or, necessarily, should see. Information that you can access and features that can be customized are as follows: Custom Feature Factory Setting What you are allowed to change Language English Choose one of six languages: English, German, Spanish, French, Dutch, or Portuguese. Units of Measure U.S. Standard Selec
