ملخص المحتوى في الصفحة رقم 1
Laser In-LIne aIr shear
65706
set up and OperatIng InstructIOns
®
distributed exclusively by harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve thIs manuaL.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form withou
ملخص المحتوى في الصفحة رقم 2
cautIOn, used sa Ve thIs manuaL with the safety Keep this manual for the safety warn- alert symbol, ings and precautions, assembly, operat- indicates a hazardous ing, inspection, maintenance and cleaning situation which, if not procedures. Write the product’s serial avoided, could result in minor number in the back of the manual near the or moderate injury. assembly diagram (or month and year of nOtIce is used to purchase if product has no number). Keep address practices this ma
ملخص المحتوى في الصفحة رقم 3
b. do not operate the tool in explo- e. use safety equipment. A sive atmospheres, such as in the dust mask, non-skid safety presence of flammable liquids, shoes and a hard hat must gases, or dust. The tool is able to be used for the applicable create sparks resulting in the ignition conditions. Wear heavy- of the dust or fumes. duty work gloves during use. c. Keep bystanders, children, and f. always wear eye protec - visitors away while operating the tion. Wear ANSI-ap- tool. Distrac
ملخص المحتوى في الصفحة رقم 4
safer at the rate for which the tool is service designed. a. Tool service must be performed c. do not use the tool if the switch only by qualified repair personnel. does not turn the tool on or off. b. When servicing a tool, use only Any tool that cannot be controlled identical replacement parts. use with the switch is dangerous and only authorized parts. must be repaired. c. use only the lubricants supplied d. disconnect the tool from the air with the tool or specified by the source
ملخص المحتوى في الصفحة رقم 5
cannot be built into this product, but sYmBOLs and must be supplied by the operator. specIFIc saFetY 2. WARNING: The brass components InstructIOns of this product contain lead, a chemi- cal known to the State of California Symbol Definitions to cause birth defects (or other repro- ductive harm). (California Health & symbol property or statement Safety code § 25249.5, et seq.) No-load speed n o 3. Obey the manual for the air compres- Revolutions or reciprocation per .../min sor used to p
ملخص المحتوى في الصفحة رقم 6
physical symptoms related to vibra- tion (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nico- tine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice between dif- ferent processes. 5. Include vibration-free periods each day of work.
ملخص المحتوى في الصفحة رقم 7
• This air tool may be shipped with a FunctIOnaL descrIptIOn protective plug covering the air inlet. Remove this plug before set up. Specifications Maximum Air air supply 90 PSI Pressure tO preVent Air Inlet 1/4” -18 NPT expLOsIOn: Strokes per Minute* 2800 SPM use only clean, Air Consumption 9 SCFM @ 90 PSI dry, regulated, compressed air Cutting Capacity 18 Gauge sheet steel to power this tool. do not use Cutter Swivel 360° left or right oxygen, carbon dioxide, Cutting Width 7/32” Wi
ملخص المحتوى في الصفحة رقم 8
operation. Add a few more drops while checking the air output gauge after each hour of continual use. to set the right pressure range. 2. Attach an air hose to the compres- 8. Inspect the air connections for leaks. sor’s air outlet. Connect the air hose Repair any leaks found. to the air inlet of the tool. Other com- 9. If the tool will not be used at this ponents, such as a connector and time, turn off and detach the air sup- quick coupler, will make operation ply, safely discharge any
ملخص المحتوى في الصفحة رقم 9
putty and tighten enough to ensure OperatIng InstructIOns an air-tight seal. read the entIre ImpOrtant 3. This tool has a safety Trigger (9). saFetY InFOrmatIOn To depress the Trigger, you must section at the beginning of this first press the safety lock part of the manual including all text under Trigger out of the way. This prevents subheadings therein before set accidental activation of the Trigger. up or use of this product. 4. This tool is designed to run at 90 Inspect tool befo
ملخص المحتوى في الصفحة رقم 10
11. Remove the clamps securing the general Operating Instructions work piece to the work table. 1. If an automatic oiler is not used, add 12. If the tool requires more force to a few drops of Pneumatic Tool Oil accomplish the task, verify that the to the airline connection before use. tool receives sufficient, unobstructed Add a few drops more after each airflow (CFM) and increase the pres- hour of continual use. sure (PSI) output of the regulator up 2. Mark the line you want to cut on
ملخص المحتوى في الصفحة رقم 11
cleaning, maintenance, and user-maIntenance Lubrication InstructIOns note: These procedures are in addition to Procedures not specifically the regular checks and maintenance explained in this manual explained as part of the regular op- must be performed only by a eration of the air-operated tool. qualified technician. 1. daily - air supply maintenance: tO preVent Every day, perform maintenance on serIOus Injur Y the air supply according to the com- FrOm ponent manufacturers’ instr
ملخص المحتوى في الصفحة رقم 12
If the Laser Light ceases to function, check the batteries. t roubleshooting problem possible causes Likely solutions Decreased output. 1. Not enough air pressure and/ 1. Check for loose connections and make sure or air flow. that air supply is providing enough air flow (CFM) at required pressure (PSI) to the tool’s air inlet. do not exceed maximum air pressure. 2. Obstructed trigger. 2. clean around trigger to ensure free movement. 3. Incorrect lubrication or not 3. Lubricate using air
ملخص المحتوى في الصفحة رقم 13
parts LIst part # description QtY. part # description QtY. 21 Gear 3 1 Housing 1 22 Spindle 1 2 Valve Plug 1 3 O-Ring 1 23 Gear Pin 3 24 Ball Bearing 2 4 Spring 1 25 Nut 1 5 Valve Spindle 1 26 Washer 1 6 O-Ring 1 7 Valve Spindle 1 27 Ball Bearing 1 28 Eccentric Nut 1 8 Pin 1 29 Cutter Housing 1 9 Trigger 1 30 Lock Screw 3 10 End Plate Cap 1 31 Right Blade 1 11 Ball Bearing 1 32 Left Blade 1 12 Rear End Plate 1 33 Center Blade 1 13 Rotor Blades 4 14 Rotor 1 34 Lock Nut 3 35 Bushing 2 15 Pin 1 36
ملخص المحتوى في الصفحة رقم 14
assemBLY dIagram SKU 65706 For technical questions, please call 1-800-444-3353. Page 14
ملخص المحتوى في الصفحة رقم 15
90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, nor
