Ingersoll-Rand 1712B2/VW1035 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

03539905
Form P7109
Edition 2
March, 1999
OPERATION AND MAINTENANCE MANUAL
FOR MODEL 1712B2/VW–1035
IMPACT WRENCH
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

ملخص المحتوى في الصفحة رقم 2

WARNING LABEL IDENTIFICATION FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. WARNING WARNING WARNING Always turn off the air sup- Always wear eye protection Always wear hearing ply and disconnect the air when operating or perform- protection when operating supply hose before install- ing maintenance on this this tool. tool. ing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. WARNING WARNING WARNING Do not carry the tool by

ملخص المحتوى في الصفحة رقم 3

MAINTENANCE SECTION (Dwg. TPA1387) PART NUMBER FOR ORDERING PART NUMBER FOR ORDERING 1 Motor Housing . . . . . . . . . . . . . . VW–1036 15 Gasket Support (2) . . . . . . . . . . . 2940–200 2 Back Cap . . . . . . . . . . . . . . . . . . VW–1037 16 Hammer Case Assembly . . . . . . VW–1065 3 Seal . . . . . . . . . . . . . . . . . . . . . . . 588–216 17 Hammer Case Bushing . . . . . 2934–641 4 Plug (2) . . . . . . . . . . . . . . . . . . . . R2–227 * Hammer Case Label . . . . . . . WARNING

ملخص المحتوى في الصفحة رقم 4

MAINTENANCE SECTION Disassembly of Impact Mechanism 1. Remove the Anvil by rotating it as it is lifted out of Always wear eye protection when operating or perform- the Hammer Frame Assembly (23).. ing maintenance on this tool. 2. Lift the Hammer Frame Assembly off the rotor shaft. Always turn off the air supply and disconnect the air 3. Push the two Hammer Pins (24) out of the Hammer supply hose before installing, removing or adjusting any Frame and slide the Hammer (25) out of the Frame. access

ملخص المحتوى في الصفحة رقم 5

MAINTENANCE SECTION a. Carefully heat alternate sides of the Housing until it is very warm. b. Using thick, heavy gloves to avoid being Excessive clamping pressure will distort the Motor burned, grasp the Housing and repeat the attempt Housing and make motor installation extremely difficult. Do not insert the hammer case end of the to dislodge the Cylinder. Motor Housing more than 1” (25 mm) into the vise 12. Remove the two Air Port Gaskets (14) and Gasket jaws. supports (15) from the Housing.

ملخص المحتوى في الصفحة رقم 6

MAINTENANCE SECTION Assembly of the Impact Mechanism Assembly of the Tool 1. Coat the Hammer (25) with Ingersoll–Rand No. 100 1. Place the Hammer Case Assembly (16) over the Grease. mechanism assembly against the Gasket. Make 2. Position the Hammer inside the Hammer Frame (23) certain the Hammer Case Label is at the top of the and install the two Hammer Pins (24). tool. 3. Install the Anvil (26) through the Frame and 2. Install the Hammer Case Cap Screws (19) and Lock Hammer until it bottoms o

ملخص المحتوى في الصفحة رقم 7

7