Chief Manufacturing PTS Series دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS
Large Flat Panel Display Table Stand
PTS SERIES

ملخص المحتوى في الصفحة رقم 2

PTS SERIES Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained herein covers all

ملخص المحتوى في الصفحة رقم 3

Installation Instructions PTS SERIES LEGEND Pencil Mark Tighten Fastener Marcar con lápiz Apretar elemento de fijación Stiftmarkierung Befestigungsteil festziehen Marcar com lápis Apertar fixador Segno a matita Serrare il fissaggio Potloodmerkteken Bevestiging vastdraaien Marquage au crayon Serrez les fixations Drill Hole Loosen Fastener Perforar Aflojar elemento de fijación Bohrloch Befestigungsteil lösen Fazer furo Desapertar fixador Praticare un foro Allentare il fissaggio Gat boren Bevestigi

ملخص المحتوى في الصفحة رقم 4

PTS SERIES Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" 1/2" (Provided) PARTS A (1) B (1) C (2) D (1) E (1) 3/16" F (8) G (4) 5/16-18 x 5/8" 5/16-18 4

ملخص المحتوى في الصفحة رقم 5

Installation Instructions PTS SERIES Attaching Faceplate Assembly ASSEMBLY AND INSTALLATION 1. Align mounting holes in faceplate assembly (A) with holes in post assembly (B). (See Figure 3) WARNING: FAILURE TO PROVIDE ADEQUATE NOTE: The faceplate assembly can be placed within a four STRUCTURAL STRENGTH FOR THIS COMPONENT CAN inch range on the post assembly, dependent on size of RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE display. TO EQUIPMENT! It is the installer’s responsibility to make sure t

ملخص المحتوى في الصفحة رقم 6

PTS SERIES Installation Instructions WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40 Remove bolt 2 LBS! Always use two people and proper lifting techniques or padlock when installing or positioning display on mount. 3 if used 2. Lower display into place listening for audible "click" to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes. (See Fig. 4 and 5) WARNING: IMPROPER INSTALLATION CAN LEAD TO Pin in "Closed" DISPLAY FALLING CAUSING SERIOUS PERSONAL posit

ملخص المحتوى في الصفحة رقم 7

Installation Instructions PTS SERIES NOTE: Roll tension is preset. If the display does not remain in the desired position, perform the following roll tension adjustment procedure. 1. Remove display following the Removing Display section. 2. Remove four 5/16-18 x 5/8" button head cap screws from back of post assembly (inserted in Step 2 of Attaching Faceplate Assembly section). 3. Locate roll tension adjustment nut on back of faceplate. (See Figure 8) Roll Tension Adjustment Nut Figure 8 4. Parti

ملخص المحتوى في الصفحة رقم 8

PTS SERIES Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 8800-000016 Rev. F 2007 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 07/07 F +86-