ملخص المحتوى في الصفحة رقم 1
OPERATOR’S MANUAL
MODEL TS
ACCESSORY FOR:
STT - ALL MODELS
STC - MODELS ABOVE SERIAL NUMBER 7630001
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMATION
FOR YOUR SCAG ACCESSORY. READING THIS
MANUAL WILL PROVIDE YOU WITH MAIN-
TENANCE AND ADJUSTMENT PROCEDURES
TO KEEP YOUR ACCESSORY PERFORMING
TO MAXIMUM EFFICIENCY. THE SPECIFIC
MODELS THAT THIS BOOK COVERS ARE CON-
TAINED ON THE INSIDE COVER. BEFORE
OPERATING YOUR MACHINE, PLEASE READ
ALL THE INFORMATION ENCLOSED.
© 2004
ملخص المحتوى في الصفحة رقم 2
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your
ملخص المحتوى في الصفحة رقم 3
2.1 SAFETY INFORMATION 1.1 INTRODUCTION -NOTE- This manual has been prepared to provide the To avoid personal injury, it is imperative that all information you need to correctly assemble, operate, safety instructions be observed. and maintain this Tiger Striper. Read it carefully and keep it for future reference. 1. Read this operator's manual and the operator's manual that is supplied with the The replacement of any part on this product by other machine this attachment is used on. than the manu
ملخص المحتوى في الصفحة رقم 4
3. Repeat on opposite side. Roll Pin 4. Once the Tiger Striper is locked in the transport position, remove the quick pins securing the Tiger Striper to the mounting brackets. See Lift Up on Figure 2-3 Handle Push and Turn Pin to line up Roll Pin with Slot to Unlock FIGURE 2-1 2. Repeat this procedure on the opposite side. The machine is now ready to operate. Remove Quick Pins 2.3 REMOVING THE TIGER STRIPER The Tiger Striper can be easily removed whenever FIGURE 2-3 the machine is being transpo
ملخص المحتوى في الصفحة رقم 5
3. Attach the mounting brackets to the cross bar 5. Install the left and right hand Striper Stop between the wheel motor brackets using (4) u- Brackets (p/n 423953 & p/n 423954) to the bolts and (8) serrated flange nuts. See Figure frame and secure with (4) 3/8-16 x 1" bolts and 3-1. Do not tighten the hardware. (4) elastic stop nuts. See Figure 3-2. (4) 3/8-16 Elastic -NOTE- Stop Nut 423953 L.H. If the Tiger Striper is installed on an STT with Stop Bracket a serial number below 7219999, part nu
ملخص المحتوى في الصفحة رقم 6
3. Attach the mounting brackets to the cross bar 4.1 LAWN STRIPING between the wheel motor brackets using (4) u-bolts and (8) serrated flange nuts. See Figure HOW DOES LAWN STRIPING WORK? 3-3. Do not tighten the hardware. The “stripe” that you see on the lawn is actually light reflecting off the blades of grass. The direction in -Note- which the grass is bent determines the “light” or The Tiger Striper cannot be installed on an “dark” stripe. When the blades of grass are bent STC with a serial
ملخص المحتوى في الصفحة رقم 7
"Checkerboard" pattern: LAWN STRIPING GUIDELINES Begin by mowing the perimeter around the property A stripe pattern can add richness and depth to any (Reference Figure 4-1). Next, mow in opposing lawn. Here are some guidelines to help produce various patterns and to enhance your striping directions (North and South or East and West) techniques. through the remaining portion of the property (as shown in Figure 4-1). Take care when turning at the end of each row to prevent turf damage. A simp
ملخص المحتوى في الصفحة رقم 8
TIGER STRIPER ASSEMBLY - STT STT with a serial number of 7219999 or Below 4 (4x) 30 5 1 (4x) 15 30 17 2 4 (4x) 3 (4x) 5 6 7 8 1 (4x) 20 9 16 10 15 11 14 12 17 8 16 18 27 13 31 26 19 6 25 21 3 (4x) 6 6 23 7 24 22 12 27 10 27 27 11 23 26 27 28 29 27 9 STT-TS Exploded View 6
ملخص المحتوى في الصفحة رقم 9
TIGER STRIPER ASSEMBLY - STT Ref. Part No. Number Description 1 04021-09 Nut, Elastic Stop 3/8-16 2 423953 Striper Stop, L.H. 3 04001-19 Bolt, Hex Head 3/8-16 x 1" 4 04100-01 U-Bolt, 5/16-18 x 1" 5 451660 Mounting Bracket Weldment, LH. 6 04041-11 Flatwasher, 3/8-.406 x 1-1/2" 7 Gauge 7 04001-22 Bolt, Hex Head 3/8-16 x 2-3/4" 8 04019-04 Nut, Serrated Flange 3/8-16 9 04050-02 Retaining Ring, .750 External "E" 10 461777 Pin, Lift Latch 11 04060-01 Pin, Slotted Spring .156 x 3/4" 12 482896 Spring,
ملخص المحتوى في الصفحة رقم 10
TIGER STRIPER ASSEMBLY - STC 4 (4x) 1 17 6 7 8 20 1 9 16 5 15 16 10 14 11 12 8 18 13 27 26 25 6 19 15 21 6 23 6 7 24 28 12 10 25 25 11 23 26 25 3 25 2 25 9 STC-TS Exploded View 8
ملخص المحتوى في الصفحة رقم 11
TIGER STRIPER ASSEMBLY - STC Ref. Part No. Number Description 1 423966 Spacer, Striper Mounting 2 43653 Roller Shaft 3 48100-24 Bushing, .752 Oilite 4 04100-01 U-Bolt, 5/16-18 x 1" 5 451660 Mounting Bracket Weldment, LH. **L.H. Mounting Bracket is used on the Right Side on STC 6 04041-11 Flatwasher, 3/8-.406 x 1-1/2" 7 Gauge 7 04001-22 Bolt, Hex Head 3/8-16 x 2-3/4" 8 04019-04 Nut, Serrated Flange 3/8-16 9 04050-02 Retaining Ring, .750 External "E" 10 461777 Pin, Lift Latch 11 04060-01 Pin, Sl
ملخص المحتوى في الصفحة رقم 12
NOTES 10
ملخص المحتوى في الصفحة رقم 13
LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the accessory to the dealer for warranty work
ملخص المحتوى في الصفحة رقم 14
© 2004 PART NO. 03158 SCAG POWER EQUIPMENT PRINTED 8-2004 DIVISION OF METALCRAFT OF MAYVILLE, INC PRINTED IN USA WWW.SCAG.COM
