ملخص المحتوى في الصفحة رقم 1
OPERATOR’S MANUAL
MODEL SSZ
PART NUMBER 03032
ملخص المحتوى في الصفحة رقم 2
WARNING:
REMEMBER - Y
ملخص المحتوى في الصفحة رقم 3
Your mower was built to the highest standards in the industry. However, your mower is only as safe as you, the operator, make it. Carelessness or error on the part of the operator may result in serious bodily injury. Hazard control and accident prevention depend upon the awareness, con- cern, prudence, and proper training of the personnel involved in the operation, transport, and storage of this equipment. Make sure every operator is properly trained and thoroughly familiar with all of the c
ملخص المحتوى في الصفحة رقم 4
SAFETY INSTRUCTIONS - CONT’D -2 & '
' * 3 ' ' + '
&
' '1 + "
& ) , ; + ) +
'
'' & ' & ,
+ +
' # ) =: %%> ?
< 4
ملخص المحتوى في الصفحة رقم 5
HYDRAULIC SAFETY DUMP VALVE RUN LEVER FREE
&
+ & POSITION WHEEL )
',
POSITION
WARNING: &
''
#
(
)
#
#
ملخص المحتوى في الصفحة رقم 6
ADJUSTMENTS - CONT’D Neutral Adjustment Cont'd 3 + 1'
4 1 )
& 5
) & )
)
&< )
'
12$+
' ' DRIVE WHEELS & 1 & 1' CASTER WHEELS 12 PSI 25 PSI
* ESC202G Figure 3 Straight Line Running Adjustment 12
ملخص المحتوى في الصفحة رقم 7
ADJUSTMENTS - CONT’D . 1 *
) *
A1 *
*
') D-E 7 Straight Line Running Adj. - Cont'd 1 *+ +
+F<*
,"-5 "67 809"-: / 1& *
*')+ "67 5.;"67 4
ملخص المحتوى في الصفحة رقم 8
. " +
)
B7:.7C>$%% ADJUSTMENTS - CONT’D : & '+
+ ,&
+ &
' + Drive Belt Replacement B @'
-
* &
+ C # G> %% CAUTION: / 0
)
B -7:27C
When replacing the drive system belt use ex- ) )
treme caution. The idler arm is under spring
)
* -
ملخص المحتوى في الصفحة رقم 9
INITIAL RUN, INSPECTION, AND 7
+* 0 ' OPERATING INSTRUCTIONS - & * & ' CONT’D ,1
=#
1' ? 5 + A '* + CAUTION: *
' ++ ' && CAUTION: Stop engine and remove key from +* ++
ملخص المحتوى في الصفحة رقم 10
INITIAL RUN, INSPECTION, AND *
- .> .. OPERATING INSTRUCTIONS - CONT’D - && + , ') & ' +,&
')+ Y ) *
& X 0 1 . '
)
, + DO NOT CUT IN, * , ') & ' + ANGLE BLADE LEAVE ORIGINAL ) + + BACK STARTING POINT SC210G / 9 &
ملخص المحتوى في الصفحة رقم 11
MAINTENANCE - CONT'D g Curb Climbing : )+ +' ) *,& + , ) ) +
* )
+) * ' : * )
) *, ' * &
* ' ' ,"-.0/ SC212G Figure 12 9
ملخص المحتوى في الصفحة رقم 12
LUBRICATION & MAINTENANCE Break-In 8 hours (Daily) 40 hours (Weekly) 100 hours (Biweekly) 200 hours (Monthly) Procedure Comments X Check all hardware for proper tightness X Change engine oil and filter at 5 hours See engine manufacturer information X Check belt tension 2 hour, 4 hour, and 8 hour intervals. X Check engine oil level Do not overfill X Remove debris from oil cooler See engine manufacturer information X Clean hydraulic pump cooling fins MORE OFTEN IF NEEDED X Remove debris from under
ملخص المحتوى في الصفحة رقم 13
TROUBLESHOOTING CUTTING CONDITIONS CAUSE CONDITION CURE Stringers - Occasional Low engine RPM Run engine at full 3600 RPM Blades of Uncut Grass Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation Clean underside of deck Width of Deck Belts slipping Adjust belt tensions SGB020 Streaking - Strips of Dull, worn blades Sharpen blades Uncut Grass in Cutting Path Incorrect
ملخص المحتوى في الصفحة رقم 14
TROUBLESHOOTING CAUSE CONDITION CURE Uneven Cut on Flat Lift worn off of blade Replace blade Ground - Wavy High-Low Blade upside down Mount with cutting edge toward Appearance, ground Scalloped Cut, or Rough Contour Deck plugged,grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SCAG dealer Bent spindle area See your authorized SCAG dealer Dull blade Sharpen blade Width of Deck SGB020 Uneven Cut on Uneve
ملخص المحتوى في الصفحة رقم 15
TROUBLESHOOTING CAUSE CURE CONDITION Scalping - Blades Low tire pressures Check and adjust pressures Hitting Dirt or Cutting Very Close to Ground speed too fast Slow speed to adjust for conditions the Ground Cutting too low May need to reduce ground speed, raise cutting height, change direction of cut, and/or change pitch and level Rough terrain May need to reduce ground speed, raise cutting height, and/or change direction of cut Ground speed too fast Slow speed to adjust for conditions Wet gras
ملخص المحتوى في الصفحة رقم 16
SPECIFICATIONS FOR SCAG SSZ ZERO-TURN RIDER MODELS:SSZ-18CV, SSZ-20CV, SSZ-22CV, ALL SSZ-LT ENGINE General Type: Heavy duty industrial/commercial Brand: Kohler Model: Kohler 18CV, 20CV, 22CV Command Vertical Engine Horsepower: 18HP, 20HP, 22HP @ 3600 RPM Type: 4 cycle gas, twin cylinder, vertical shaft engine Displacement: 18HP=624 cc, 20HP=624cc, 22HP=624cc Cylinders: 2 cast-iron sleeves Governor: Mechanical type governor with variable speed control set at 3600 rpm (+ 100rpm), idle set at 1400
ملخص المحتوى في الصفحة رقم 17
SPECIFICATIONS FOR SCAG SSZ ZERO-TURN RIDER MODELS:SSZ-18CV,SSZ-20CV, SSZ-22CV, ALL SSZ-LT CUTTER DECK SMZ 48, SMZ 52, SMZ 61 Type: Floating, adjustable, anti-scalping, hybrid design combines out-front and belly-mount designs Construction: 10-gauge steel with 7-gauge (3/16") steel skirt True Cutting Width: 48.0" (122.0 cm), 52" (132.0 cm), 61: (155.0 cm) Cutting Height Adjustment: Hand operated lever adjustment from operator's seat, 1-3/4" to 4-1/2" in 1/2" increments SSZ-LT=2-1/4" to 5-1/4" in
ملخص المحتوى في الصفحة رقم 18
48", 52" & 61" CUTTER DECKS 32 70 24 67 69 65 68 24 3 3 31 38 70 34 32 27 28 26 36 37 39 B 31 4 30 66 23 22 18 42 21 71 25 64 18 17 10 47 41 16 15 45 11 25 A 25 48 46 41 13 13 49 20 39 43 12 35 6 8 24 49 44 3 20 40 B A 7 20 52 14 10 5 53 24 3 54 55 12 60 25 14 2 1 56 50 61 58 62 63 4 59 54 9 51 29 57 33 19 SC214G 2
ملخص المحتوى في الصفحة رقم 19
48", 52", & 61" CUTTER DECKS - CONT’D Ref. Part Ref. Part No. Number Description 48 52 61 No. Number Description 48 52 61 1 46852 Cutter Deck (Includes decals) X 39 04041-12 Flatwasher, 3/8" (.375 x 1.5 x .06) X X X 46615 Cutter Deck (Includes decals) X 40 48807 Spring, Idler Tension X X X 46611 Cutter Deck (Includes decals) X 41 48100-02 Bushing X X X 2 421058 Belt Cover, Front X 42 46750 Idler Arm (Includes bushings & 421451 Belt Cover, Front X grease fittings) X X 421299 Belt Cover, Front X
ملخص المحتوى في الصفحة رقم 20
CUTTER DECK CONTROLS 48", 52", & 61" DECKS 10 8 9 13 11 5 12 17 18 7 15 5 4 35 17 19 19 3 6 34 35 5 2 5 1 23 2 2 22 33 25 2 5 21 16 23 2 14 34 20 37 26 14 20 16 2 27 2 29 24 32 26 14 23 30 30 29 14 36 31 14 29 29 28 14 48" DECK SC215G 4
