ملخص المحتوى في الصفحة رقم 1
NPS-520
MFP Print Server
Quick Start Guide
Version 1.00
Edition 2
1/2007
Table of Contents
ENGLISH 1
DEUTSCH 19
ESPAÑOL 39
FRANÇAIS 59
ITALIANO 79
РУ ССКИЙ 99
SVENSKA 119
Copyright © 2007. All rights reserved.
ملخص المحتوى في الصفحة رقم 2
EN ENGLIS GLISH H Overview The NPS-520 is a print server and comes with one Ethernet port and one USB (v2.0) port. You can use the USB port to share a printer with the computers in the network to which the NPS-520 (labeled NPS in the following graphic) is connected. Through the NPS-520, the printer works as if it is connected directly to your computer. You should have already installed the driver (and utility if there is one) for the printer (connected to the NPS-520) on your computer.
ملخص المحتوى في الصفحة رقم 3
ENGLISH 3 Use the web configurator to manage the NPS-520. Windows users can use the utility or web configurator to configure the NPS-520. Macintosh and Linux/UNIX users can use the web configurator to configure the NPS-520. See page 16 for a list of system requirements. If your computer operating system version is older than Windows 2000 SP4, you can only print on a printer even if the printer provides print, copy, fax and/or scan functions. 1 Hardware Connection Follow the steps below to
ملخص المحتوى في الصفحة رقم 4
ENGLISH 1 Connect the USB port to a USB v2.0 compliant printer using a USB cable. 2 Connect the LAN port to your local network using an Ethernet cable. 3 Use the included power adaptor to connect the power socket on the NPS-520 to an appropriate power source. 1.1 LEDs Look at the LEDs (lights) on the top panel. The READY LED stays on when the system is ready. The LAN LED stays on if the LAN port is properly connected and blinks when there is traffic. If none of the LEDs are on, check yo
ملخص المحتوى في الصفحة رقم 5
ENGLISH 2 ZyXEL Utility Use the utility to install and associate your printer driver as well as manage the NPS-520. 2.1 Utility Installation on Windows The NPS-520’s default IP address is 192.168.1.6. The installation procedures are similar for all supported Windows versions. 1 Insert the included CD into the CD-ROM drive on your computer (that is connected to the NPS-520 directly or connected to your network). When the following screen displays, click Setup. If the screen does no
ملخص المحتوى في الصفحة رقم 6
ENGLISH 2 Select your preferred language and click OK. 3 The following screen displays. Click Next. 5
ملخص المحتوى في الصفحة رقم 7
ENGLISH 4 Click Next to accept the default file location or click Change to select an alternate folder. 5 Select Yes, I want to configure the ZyXEL NPS-520 now and click Next to configure the NPS-520 now. 6
ملخص المحتوى في الصفحة رقم 8
ENGLISH 6 Your unique NPS-520’s device name automatically displays in the text box. If it does not show up, click Refresh to update this screen. Click Next. 7 Enter the default password (1234) and click OK. 8 Replace the unique generated device name with a more friendly recognizable name with additional descriptive text if you want. Alternatively, leave the fields at the default settings. Click Next. 7
ملخص المحتوى في الصفحة رقم 9
ENGLISH 9 If the NPS-520 is connected to a network that has a DHCP server, select DHCP to have the DHCP server assign TCP/IP information (such as IP address and subnet mask) to your NPS-520. Otherwise, select Manual IP and enter an IP address (in the same subnet as your network), subnet mask and the gateway’s IP address. Click Next. We recommend you give the NPS-520 a static IP address or configure your DHCP server to always give it the same IP address (static DHCP). If the NPS-520’s IP
ملخص المحتوى في الصفحة رقم 10
ENGLISH If you selected DHCP in the previous screen but there was no DHCP server found in your network, the following screen displays. Click Yes to go back to the TCP/IP configuration screen or click No to have the NPS-520 search for the DHCP server again. If your computer and the NPS-520 are not in the same subnet, the following screen pops up. Click OK (or Yes) to continue. 10This read-only screen shows the current settings. Check whether what you have configured is correct and click 9
ملخص المحتوى في الصفحة رقم 11
ENGLISH Finish. Otherwise, click Back to re-configure the information. 11Click Finish to complete the installation. 12Repeat these steps on each Windows computer in your network that will use the NPS-520. 10
ملخص المحتوى في الصفحة رقم 12
ENGLISH 2.2 Using the Utility on Windows If you already installed a printer driver, you still need to associate it with the NPS-520. 2.2.1 Printer Driver Installation and Association 1 Start the ZyXEL utility by either double-clicking the utility icon in the system tray or clicking Start > (All) Programs > ZyXEL NPS-520 Utility > NPS-520 Utility. 2 The Status screen displays. Select the name of your NPS- 520 and click Connect. 3 Windows automatically detects the printer and prompts you to in
ملخص المحتوى في الصفحة رقم 13
ENGLISH instructions to install a new driver and/or have the driver associate with the NPS-520. 2.2.2 Managing the NPS-520 To have computers in the network take turns to use the printer, you need to enable Auto Connect in the utility Status screen and select a default printer. Auto connect allows the NPS-520 to communicate with the printer when you want to use it. The NPS-520 drops the connection after the job is finished. Alternatively, click Connect and set the Auto Release idle timeout
ملخص المحتوى في الصفحة رقم 14
ENGLISH If you disable Auto Release, only that computer can use the printer. Click Disconnect to manually drop the connection. The Auto Release and Auto Connect features are not configurable if your computer operating system version is older then Windows 2000 SP4. 13
ملخص المحتوى في الصفحة رقم 15
ENGLISH If the printer is not connected or not available when you send out a request, the request will be put in your computer’s print queue until the printer is available. If you cannot use the printer, make sure you enable Auto Release and/or Auto Connect on all Windows computers. 3 Web Configurator Follow the steps below to use the web configurator to configure the NPS-520’s TCP/IP settings. See your User’s Guide for more information and how to add a printer on your computer. Use
ملخص المحتوى في الصفحة رقم 16
ENGLISH 3 Type “1234” (default) as the password and click Login. If the login screen does not display, make sure your computer is in the same subnet as the NPS-520. You may also need to check your browser’s security settings and make sure your computer’s Ethernet card is installed and functioning properly. 4 Click Setup TCP/IP to configure the NPS-520’s IP address. If the NPS-520 is connected to a network that has a DHCP server, select Obtain IP automatically to have the DHCP server as
ملخص المحتوى في الصفحة رقم 17
ENGLISH We recommend you give the NPS-520 a static IP address or configure your DHCP server to always give it the same IP address (static DHCP). If the NPS-520’s IP address changes, you need to uninstall and reinstall the ZyXEL utility on each computer that uses it. Click Apply to save your changes. 4 System Requirements Before installation, make sure you have a computer with the following: • Pentium II 300 MHz or above • A minimum of 20 MB available hard disk space 16
ملخص المحتوى في الصفحة رقم 18
ENGLISH • A minimum of 32 MB RAM • A CD-ROM drive • Windows 98 Second Edition (SE), Windows Me, Windows 2000, Windows 2003, Windows XP, Unix/Linux (with LPR/ LPD protocol support), Mac OS 9.x or later • Windows 98 SE users may need the Windows 98 SE CD Procedure to View a Product's Certification(s) 1 Go to www.zyxel.com. 2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. 3 Select the certification you wish to view from this page. 17
ملخص المحتوى في الصفحة رقم 19
ENGLISH 18
ملخص المحتوى في الصفحة رقم 20
DEUTSCH DEUTSCH Übersicht Der NPS-520 ist ein Druckserver mit einem Ethernet- und einem USB-Anschluss (v2.0). Am USB-Anschluss des NPS- 520 (in der folgenden Abbildung als NPS bezeichnet) kann ein Drucker angeschlossen werden, welcher dann von allen Computern des Netzwerkes verwendet werden kann. Über den NPS-520 arbeitet der Drucker, als wäre er direkt an dem Computer angeschlossen. Der Treiber (und wenn vorhanden das Utility- Programm) des Druckers (der an dem NPS-520 angeschlossen ist)
