Korg SQ-10 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

USER'S MANUAL

ملخص المحتوى في الصفحة رقم 2

2

ملخص المحتوى في الصفحة رقم 3

CONTENTS 1. ABOUT ANALOG SEQUENCERS........................................................................................................................ 4 2. FEATURES OF THE KORG SQ-10 ANALOG SEQUENCER .......................................................................... 4 3. FEATURES AND FUNCTIONS............................................................................................................................. 5 3.1. VOLTAGE CONTROLLED CLOCK GENERATOR (CLOCK)..........

ملخص المحتوى في الصفحة رقم 4

1. About Analog Sequencers Most people think of an analog sequencer as basically a device which can "play" a series of pre-determined notes on a synthesizer automatically. This is the most common usage to which a sequencer is put to. But in fact, the SQ-10 Analog Sequencer is capable of much more than simply establishing sequences of pitch levels. It should be remembered that the monophonic synthesizer is a device which uses voltage control to vary the three elements of musical so

ملخص المحتوى في الصفحة رقم 5

3. Features and Functions [ BOLD Italic underlined numbers refer to the front panel illustration. See 7 FoldOut ] 3.1. Voltage Controlled Clock Generator (Clock) Use this clock when you want to run through the steps automatically. Clockspeed is controlled by voltage, so you can use Channel-C to vary the step spacing or any other source to control the overall speed. 1 Clock speed: Use this knob to adjust the basic speed of the sequence when you advance the steps auto

ملخص المحتوى في الصفحة رقم 6

3.5. Sequence Mode 9 Mode Selector: This 6 position control selects the type of sequence...stepped, continuous or one-time...for 12 or 24 step sequences. sequence modes 3.6. Portamento 10 Portamento A, B: Ordinarily the voltage changes in a sequence form a sharply stepped progression, but with this knob you can make these changes smoother and get a portamento effect. 3.7. Duty 11 This adjusts the multiple trigger width as the st

ملخص المحتوى في الصفحة رقم 7

3.9. Reset 15 Reset In: Use this INPUT jack when you want less than the maximum number of steps in a sequence. Just patch the Trig Out jack of the last step in the sequence to the RESET IN jack. When the sequence reaches that step, it will be reset and begin again at step 1. 3.10. Output Voltage Control 16 Range Switch ( +/-1V < > +/-5V ): When you want to control synthesizer functions with a smaller voltage range, use the +/-1V position. 17 LED's: These light emitting dio

ملخص المحتوى في الصفحة رقم 8

4. Specifications 1. VOLTAGE CONTROLLED CLOCK GENERATORSPEED CONTROL [SLOW ~ FAST] 2. SEQUENCE MODE 3. STEP --> (MANUAL) 4. PORTAMENTO PORTAMENTO CHANNEL (A) PORTAMENTO CHANNEL (B) 5. TRIGGER DUTY (MULTIPLETRIGGER, CHANNEL C) 6. SEQUENCE CONTROL CHANNEL A ( 1 ~ 12 ) CHANNEL B ( 1 ~ 12 ) CHANNEL C ( 1 ~ 12 ) TRIG OUT ( 1 ~ 12 ) LED ( 1 ~ 12 ) 7. SEQUENCE VOLTAGE OUT ( A ) -5V ~ +5V / -1V ~ +1V ( B ) -5V ~ +5V / -1V ~ +1V

ملخص المحتوى في الصفحة رقم 9

6. Examples of usages 6.1. Repeated automatic playing For repeated automatic playing of 12 notes (using the MS-10 synthesizer) 9

ملخص المحتوى في الصفحة رقم 10

6.2. Tone color changes For a 24 note sequence in which the tone color changes when a new note is played on the keyboard. 10

ملخص المحتوى في الصفحة رقم 11

6.3. Blank patch chart 11

ملخص المحتوى في الصفحة رقم 12

7. SQ -101 Fold Out 12