ページ1に含まれる内容の要旨
USER'S MANUAL
ページ2に含まれる内容の要旨
2
ページ3に含まれる内容の要旨
CONTENTS 1. ABOUT ANALOG SEQUENCERS........................................................................................................................ 4 2. FEATURES OF THE KORG SQ-10 ANALOG SEQUENCER .......................................................................... 4 3. FEATURES AND FUNCTIONS............................................................................................................................. 5 3.1. VOLTAGE CONTROLLED CLOCK GENERATOR (CLOCK)..........
ページ4に含まれる内容の要旨
1. About Analog Sequencers Most people think of an analog sequencer as basically a device which can "play" a series of pre-determined notes on a synthesizer automatically. This is the most common usage to which a sequencer is put to. But in fact, the SQ-10 Analog Sequencer is capable of much more than simply establishing sequences of pitch levels. It should be remembered that the monophonic synthesizer is a device which uses voltage control to vary the three elements of musical so
ページ5に含まれる内容の要旨
3. Features and Functions [ BOLD Italic underlined numbers refer to the front panel illustration. See 7 FoldOut ] 3.1. Voltage Controlled Clock Generator (Clock) Use this clock when you want to run through the steps automatically. Clockspeed is controlled by voltage, so you can use Channel-C to vary the step spacing or any other source to control the overall speed. 1 Clock speed: Use this knob to adjust the basic speed of the sequence when you advance the steps auto
ページ6に含まれる内容の要旨
3.5. Sequence Mode 9 Mode Selector: This 6 position control selects the type of sequence...stepped, continuous or one-time...for 12 or 24 step sequences. sequence modes 3.6. Portamento 10 Portamento A, B: Ordinarily the voltage changes in a sequence form a sharply stepped progression, but with this knob you can make these changes smoother and get a portamento effect. 3.7. Duty 11 This adjusts the multiple trigger width as the st
ページ7に含まれる内容の要旨
3.9. Reset 15 Reset In: Use this INPUT jack when you want less than the maximum number of steps in a sequence. Just patch the Trig Out jack of the last step in the sequence to the RESET IN jack. When the sequence reaches that step, it will be reset and begin again at step 1. 3.10. Output Voltage Control 16 Range Switch ( +/-1V < > +/-5V ): When you want to control synthesizer functions with a smaller voltage range, use the +/-1V position. 17 LED's: These light emitting dio
ページ8に含まれる内容の要旨
4. Specifications 1. VOLTAGE CONTROLLED CLOCK GENERATORSPEED CONTROL [SLOW ~ FAST] 2. SEQUENCE MODE 3. STEP --> (MANUAL) 4. PORTAMENTO PORTAMENTO CHANNEL (A) PORTAMENTO CHANNEL (B) 5. TRIGGER DUTY (MULTIPLETRIGGER, CHANNEL C) 6. SEQUENCE CONTROL CHANNEL A ( 1 ~ 12 ) CHANNEL B ( 1 ~ 12 ) CHANNEL C ( 1 ~ 12 ) TRIG OUT ( 1 ~ 12 ) LED ( 1 ~ 12 ) 7. SEQUENCE VOLTAGE OUT ( A ) -5V ~ +5V / -1V ~ +1V ( B ) -5V ~ +5V / -1V ~ +1V
ページ9に含まれる内容の要旨
6. Examples of usages 6.1. Repeated automatic playing For repeated automatic playing of 12 notes (using the MS-10 synthesizer) 9
ページ10に含まれる内容の要旨
6.2. Tone color changes For a 24 note sequence in which the tone color changes when a new note is played on the keyboard. 10
ページ11に含まれる内容の要旨
6.3. Blank patch chart 11
ページ12に含まれる内容の要旨
7. SQ -101 Fold Out 12
