ملخص المحتوى في الصفحة رقم 1
Front cover
User’s Manual
EDID 101D & EDID 101V
™
EDID Emulator with EDID Minder
68-1773-01
Rev. A
06 09
ملخص المحتوى في الصفحة رقم 2
Precautions Safety Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety the literature provided with the equipment. feature, do not attempt to bypa
ملخص المحتوى في الصفحة رقم 3
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 注意 没有用户可以更换的零件。为避免出现触电危险不要自 阅读说明书 • 用户使用该设备前必须阅读并理 己试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 遵守警告 • 用户应遵守产品和用户指南上的所有安 与厂家推荐的相同或相近型号的电池。 按照生产厂的 全和操作说明。 建议处理废弃电
ملخص المحتوى في الصفحة رقم 4
Table of Contents About this Manual ....................................................................... 1 About the EDID 101 ..................................................................... 1 EDID 101 Features ......................................................................... 2 Mounting the EDID 101 .............................................................. 5 Tabletop placement .................................................................. 5 Rack mounting ...............
ملخص المحتوى في الصفحة رقم 5
About this Manual This manual contains information about the Extron EDID 101D/EDID 101V, with instructions on how to mount and operate the unit. Throughout this manual EDID 101 is used to refer to the EDID 101D and EDID 101V. Where differences may occur, they are noted. About the EDID 101 The EDID 101D and EDID 101V are compact, economical ™ EDID Minder devices that record and manage display EDID (Extended Display Identification Data). A source device normally uses EDID to identify
ملخص المحتوى في الصفحة رقم 6
Introduction EDID 101 Features EDID Minder — Enables continuous EDID communication to the input source. EDID provides information about a display identity. The EDID Minder continuous EDID communication helps ensure the source boots up properly and reliably outputs content to the display. EDID Record — Enables the device to record EDID directly from a display. Pre-programmed EDID — The EDID 101 contains pre-programmed EDIDs with the most common display native resolutions for both 50 and
ملخص المحتوى في الصفحة رقم 7
D-SUB NPUT (SOURCE) DVI INPUT (SOURCE) Mac-Mini EDID 101D DVI-DVI DVI-DVI DVI DA2 DVI DISTRIBUTION AMPLIFIER DVI-DVI Projector DVI DA2 EDID 101D VGA-VGA VGA-VGA EDID 101V PC (No EDID Passed) EDID to PC AUDIO IN COMPUTER IN RGB LEVEL PEAKING MTP SERIES Twisted Pair VGA-VGA Projector MTP RL 15 HD RS MTP 15 HD A D EDID 101V Typical EDID 101 applications EDID 101D/EDID 101V • Introduction 3 DVI OUTPUT (DISPLAY) D-SUB OUTPUT (DISPLAY)
ملخص المحتوى في الصفحة رقم 8
EDID 101D EDID 101D VGA INPUT (SOURCE) VGA INPUT (SOURCE) D-SUB NPUT (SOURCE) DVI INPUT (SOURCE) Introduction, cont’d Extron Projector Crosspoint 300 42 HVA Wideband Matrix Switcher Flat Panel Display Extron Extron PC EDID 101V EDID 101V Laptop EDID Minder EDID Minder Mac-Mini EDID 101D DVI-DVI DVI-DVI IN1508 INPUT OUTPUT RATE PIP PICTURE CONTROL SCALING PRESENTATION SWITCHER IR CONT/ COL/ 1 2 3 4 5 6 7 8 ON SWAP CENTER SIZE BRT TNT MENU ENTER VGA 1024x852 UXGA SVGA 1024x1024 720p XGA 1366x768 1
ملخص المحتوى في الصفحة رقم 9
Mounting the EDID 101 The EDID 101 is housed in a 1/8 rack width, 3" deep, 1" high metal enclosure. The small form factor is ideal for connecting the EDID 101 between two devices that would otherwise be directly connected. After the EDID 101 is mounted, the side panel may be N inconvenient or impossible to access for configuration. To avoid uninstalling, program it prior to mounting. See page 10, "EDID 101D/EDID 101V Operation" for programming details. Tabletop placement Attach the
ملخص المحتوى في الصفحة رقم 10
Installation and Operation, cont’d Rack mounting procedures The unit can be mounted in the front or rear of any of these rack systems: • RSF 123 rack shelf kit for 3.5" deep products (part #60-190-20) • RSB 123 basic rack shelf kit for 3.5" deep products (part #60-604-20) • RSU 126 universal rack shelf kit for 6" deep products (part #60-190-10) • RSB 126 basic rack shelf kit for 6" deep products (part #60-604-10) • RSU 129 universal rack shelf kit for 9.5" deep products (part #60-190-
ملخص المحتوى في الصفحة رقم 11
Furniture mounting The EDID 101 can be mounted under furniture using optional mounting kit MBU 125 (part #70-077-01) as follows: 1. Attach the mounting brackets to the EDID 101 with the provided machine screws as shown in the figure below. 2. Hold the EDID 101 with the attached brackets against the underside of the table or other furniture. Mark the location of the screw holes in the brackets on the mounting surface. 3. Drill 3/32" (2.4 mm) diameter pilot holes, 1/4" (6.3 mm) deep in the
ملخص المحتوى في الصفحة رقم 12
Installation and Operation, cont’d Panel Features EDID 101D ON 1 2 EDID DVI OUTPUT (DISPLAY) 60 DIGITAL SELECT DVI INPUT (SOURCE) RECORD Hz POWER SIGNAL 12V 50 ANALOG 0.4A MAX g ab cd e f EDID 101V ON CONFIG 1 2 EDID VGA OUTPUT (DISPLAY) SELECT 60 VGA INPUT (SOURCE) Hz RECORD SPARE POWER 12V 50 0.4A MAX EDID 101 Panel views Side panel Power LED — Dual-color multi-purpose LED: a Green — Indicates power is connected from the 5 VDC pin of a DVI/VGA video source or by the option
ملخص المحتوى في الصفحة رقم 13
Front and rear panels Power connector — An optional external 12 VDC power e supply may be connected to this 2-pole, 3.5 mm captive screw connector. During normal operation the EDID 101 is powered N using +5 VDC from pin 9 of a DDC compliant VGA source (EDID 101V) or pin 14 of a DVI source (EDID 101D). If the source is capable of providing power for the EDID 101, the green Power LED ( ) will light when a the source is connected and powered on. When the EDID 101 is powered from a vide
ملخص المحتوى في الصفحة رقم 14
Installation and Operation, cont’d EDID 101D/EDID 101V Operation The EDID 101 can either record EDID from a display device or a pre-programmed EDID can be selected using the rotary and DIP switches. Recording a display EDID To record a new EDID into memory: 1. Turn the rotary switch ( ) to position 0. d The DIP switch positions have no effect in this mode. N 2. Apply power to the EDID 101 by connecting a power source. If power is not available from a video source, an external N 12 V
ملخص المحتوى في الصفحة رقم 15
B A 9 8 7 6 5 Using the pre-programmed Extron EDID Configuring the EDID 101 rotary and DIP switches allow N a user to select a pre-programmed EDID based on the native rate of a display (i.e. 1280x1024 @ 60 Hz) and a desired signal type (i.e. digital), but does not necessarily force a video source to output that rate. Since EDID is not limited to reporting a single video rate (i.e. the native rate), each Extron EDID also lists other common video rates for use by the video source. 1.
ملخص المحتوى في الصفحة رقم 16
Reference Material Specifications If you use a DVI-A to 15-pin HD adapter, the EDID 101D can N be used for analog signal pass-through. Video — EDID 101D, digital signals Maximum data rate....................... 10 Gbps (3.3 Gbps per color) Maximum pixel clock ................... 330 MHz (165 MHz per link) Resolution range ........................... Up to 2560x1600 @ 60 Hz Formats ........................................... RGB and YCbCr digital video Standards ..............................
ملخص المحتوى في الصفحة رقم 17
General Power .............................................. Supplied by the 5 V signal from a DVI source (pin 14), a VGA* source (pin 9), or from an external power supply N *Some VGA source devices do not provide power output. External power supply ................. 100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated Power input requirements ........... 12 VDC, 0.05 A Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
ملخص المحتوى في الصفحة رقم 18
Reference Material, cont’d Included Parts These items are included in each order for an EDID 101: Included parts Replacement part number EDID 101D 60-990-01 -or- EDID 101V 60-991-01 (4) Rubber feet (unattached) (2) Strips of Velcro (unattached) EDID 101D/EDID 101V Setup Guide Accessories Accessories Part number PS 1210C 12 VDC, 1 A power supply 70-775-01 RSU 129, universal rack shelf kit for 9.5" 60-190-01 deep products (gray) RSB 129, basic rack shelf kit for 9.5" deep 60-604-01, -02
ملخص المحتوى في الصفحة رقم 19
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within
ملخص المحتوى في الصفحة رقم 20
Back cover: contact information Extron USA - West Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +400.883.1568 +971.4.2991800 Inside USA / Canada Only Inside Europe Only Inside Asia Only Inside China Only +800.633.9876 +81.3.3511.7656 FAX +971.4.2991880 FAX Inside USA / Canada Only +1.919.863.1794 +31.33.453.4040 +65.6383.4400 +86.21.3760.1568 +1.714.491.1500 +1.919.863.1797 FAX +3
