ملخص المحتوى في الصفحة رقم 1
Use and Care of Recirculation Hood Models JN322, JN334, JN335,
JMW, & JN635 and Ventilating Hood Models JV322, JV324, JV332,
JV334, JV335, JV624, JV634, & JV635
C. When cutting or drilling into wall or ceiling,
IMPORTANT SAFETY
do not damage electrical wiring and other
INSTRUCTIONS hidden utilities.
D. Ducted fans must always be vented to
WARNING- TO REDUCE THE RISK
the outdoors.
OF FIRE, ELECTRIC SHOCK, OR
E. If this unit is to be installed over a tub or
INJURY TO PERSONS, OBSERVE
shower, it mu
ملخص المحتوى في الصفحة رقم 2
If You Need Service... ● Do not attempt to repair or replace any part of 1 IMPORTANT SAFETY your hood unless it is speciikxdly recommended INSTRUCTIONS {continu~) in this book. All other servicing should be referred to a qualified technician. WARNING TO REDUCE THE RISK ● Disconnect hood circuit breaker or fuse before OF INJURY TO PERSONS ~ T~ performing any service. EVENT OF A RANGE TOP GREASE “A” Models: JN322, JN334, JN335, JN634 & JN635 FIRE, OBSERVE THE FOLLOWING: ‘“,a,eoremovehe fi,ter A. S
ملخص المحتوى في الصفحة رقم 3
To remove: Turn the retaining clip to release the edge of To Operate the filter. The filter will then slip out of the retaining tabs. —Vents To clean: Soak and then agitate in a hot detergent (“JN” models only) solution. Light brushing may be used to remove irnbedded soil. Rinse, shake and remove moisture before replacing. With careful handling, the filter will last for yean. If replacement becomes necessary, order the part from your dealer. Lamp switch Fan switch Trim To replace: Slip the edge
ملخص المحتوى في الصفحة رقم 4
Installation Instructions for General Electric Hood Models: JN322, JN334, JN335, JN634, JN635, JV322, JV324, JV332, JV334, JV335, JV624, JV634, JV635 Important-save for the local electrical inspector% use Power supply connection box on underside of hood. I 7%” ~pe “C” Y~ models Exhaust Outlet Knockouts — 4
ملخص المحتوى في الصفحة رقم 5
1. PREPARATION OF WALL CABINET AND WALL FLUSH OR RECESSED BOITOM CABINET NOTE: For easier installation make all hood and vent cutouts in the cabinet and wall before cabinet is permanently fastened in place. It is recommended that the power supply be brought into the hood from the wall below the cabinet as shown in Fig. 1. However, an optional location is shown in Fig. 2, where the power supply enters the top of the hood by passing through the wall cabinet. A. WALL CABINET WITH RECESSED BOTTOM: -
ملخص المحتوى في الصفحة رقم 6
2. DUCT INSTALLATION Total Equivalent Number Equivalent T@e “B” Models: See Figs. 4 and 9. . Duct Pieces Length Used Length The hood exhaust has been designed to mate with standard 7“ round duct. (A round damper kit may be a ‘:~:::$ 5 feet ordered. Order GE model number JXDA22.)* 3%’’ X1O” A. If a rectangular duct is desired, a round-to-rectangular straight 2.5 feet D adapter must be used. Install a 4“ minimum length of 7“ round duct between the hood and adapter to obtain 6“, proper operation of
ملخص المحتوى في الصفحة رقم 7
3. POWER SUPPLY A. CIRCUIT VOLTAGE: This hood must be connected Centerline of hood to a supply circuit of the proper voltage and frequency as specified on the rating plate. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for hoods of this rating. The rating plate is located on the rear wall of the hood. B. FUSE RATING: 15 amPS. C. Unless otherwise specified by local codes, bring a 15 amp 2 wire circuit with ground to the area of the power s
ملخص المحتوى في الصفحة رقم 8
IMPORTANT: After installation, peel off the transparent protective film stripping from the decorative trim on the front of the hood. (See Fig. 12.) B. ELECTRICAL CONNECTION Protective Film 1. Be sure the power supply is disconnected before making electrical connections. FIGURE 12 2. Remove the connection box cover located on the left side of the fan unit. 3. Attach the power supply through the knockout hole in the back or top of the hood. 4. Connect the colored incoming power supply Wire nuts le
ملخص المحتوى في الصفحة رقم 9
Remove the lamp and replace with an ordinary screw- Lamp Replacement base lamp bulb NOT MORE THAN 60 WATTS. To remove the lamp cover, if desired: Models JN334, JN335, JN634, ● Press the sides with 2 fingers until the side prongs JN635, JV324, JV334, JV335, are released. JV624, JV634, JV635 have a ● Lift the lamp cover and slide towards you in one lamp cover. motion. The lamp cover need not be To replace the lamp cover: removed for lamp removal ● Insert the prong located at the end of the cover i
ملخص المحتوى في الصفحة رقم 10
Questions? Use This Problem Solver PROBLEM POSSIBLE CAUSE FAN DOES NOT ● A fuse may be blown or a circuit breaker tripped. Replace fuse or reset circuit breaker. OPERATE WHEN THE SWITCH IS ON . Fan blade striking the hcmd sheI1. FAN FAILS TO CIRCULATE AIR s Excessively soiled filter should be checked and corrected before using the hood again. FAN OPERATES BUT - Check to be sure the filter is clean. If replacing the filter does not correct the problem, MOVES AIR SLOWER call for service. THAN NORM
ملخص المحتوى في الصفحة رقم 11
If You Need Service Help Us Help You... To obtain service, see your warranty on the back page Write down the model and serial of this book. numbers. We’re proud of our service and want you to be pleased. You’ll find them on a label on the back wall of If for some reason you are not happy with the service the hood. These numbers are also on the Consumer you receive, here are 3 steps to follow for further help. Product Ownership Registration Card that came with your hood. Before sending in this ca
ملخص المحتوى في الصفحة رقم 12
Staple sales slip or cancelled check YOUR RANGE HOOD here. Proof of original purchase date WARRANTY is needed to obtain service I — under warranty. FULL ONE-YEAR WARRANTY This warranty is extended to WHAT IS COVERED the original purchaser and any For one year from date of original succeeding owner for products purchase, we will provide, free of purchased for ordinary home use in charge, parts and service labor in the 48 mainland states, Hawaii and your home to repair or replace any Washington, D
