Addonics Technologies ST3HPMRXA دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

T E C H N O L O G I E S
User Guide
Storage Tower III
(ST3HPMRXA)
www.addonics.com
v6.1.11
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/

ملخص المحتوى في الصفحة رقم 2

Removing Cover of Storage Tower III Loosen the 3 screws at the back of the tower using a Philips screwdriver by turning counter-clockwise. Separate the metal casing of the tower from the housing by lifting up the casing. Installing drives into the Storage Tower Secure up to three 3.5” SATA hard disk drive into the bay using optional mounting brackets. Note: It is recommended to fill up the tower III with SATA drives from top to bottom. This is to help in identifying which drives connect to

ملخص المحتوى في الصفحة رقم 3

SATA Port 2 Drive activity LED Jumper Block (J1) SATA Port 4 Error LED Jumper Block (J3) SATA Port 3 Floppy Power SATA Port 0 Connector SATA Port 1 eSATA Host Port (Port 5) Dip Switch RAID Setting Button Dip Switch Settings Raid Mode 1 2 3 4 5 Individual Drive OFF OFF OFF OFF OFF (Factory Default) 0 OFF OFF ON ON ON 1 and 10 OFF OFF ON ON OFF 3 OFF OFF ON OFF OFF 5 OFF OFF OFF ON OFF Clone OFF OFF OFF ON ON Large OFF OFF ON OFF ON Enable Auto- Port M

ملخص المحتوى في الصفحة رقم 4

Default factory DIP Switch setting: SW1 – RAID Setting DIP Switch BZS – Error buzzer function EZ – Automatic rebuilding to spare drive (one of the drives on the raid is set as a spare). If EZ is ENABLED anda drive failure occurs, the spare will automatically act as a drive replacement and rebuilding will automatically start. M2 – RAID mode 2 M1 – RAID mode 1 M0 – RAID mode 0 SW1 1 2 3 4 5 BZS EZ M2 M1 M0 1. Error buzzer function is ENABLED (BZS) wh

ملخص المحتوى في الصفحة رقم 5

Setting or Modifying the RAID Mode Using the JMicron HW RAID Manager Utility Program: 1. For Windows users, install the JMicron HW RAID Manager located on the SATA Controller CD. In the CD, go to Configuration Utilities > JMB393. This manager can be use to create and monitor the status of the RAID volume. It is recommended to use the default factory RAID DIP switch setting when using the JMicron HW RAID Manager. 2. Modify the RAID mode on the 5-port HPM-XA using DIP switch Recommende

ملخص المحتوى في الصفحة رقم 6

Setting or Modifying the RAID Mode Using the JMicron e. On the DIP switch, change (M0 to M2) setting to the desired RAID mode using the diagram below. HW RAID Manager Utility Program: All settings on the diagram shows 1. For Windows users, install the JMicron HW RAID Manager located on the • Error buzzer function is ENABLED SATA Controller CD. In the CD, go to Configuration Utilities > JMB393. This • EZ function is DISABLED. manager can be use to create and monitor the sta

ملخص المحتوى في الصفحة رقم 7

RAID Setting Notes: When 2 drives are RAID 1& RAID 10 Mode connected to the HPM-XA, and DIP switch is set to this setting, the 2 drives will be SW1 1 2 3 4 5 configured as a 2-drive RAID1 array. BZS EZ M2 M1 M0 When 4 drives are connected to the HPM-XA, the 4 drives will be configured as a 4-drive RAID10 array. Clone’s action is similar to Clone Mode RAID1. However, all of the hard drives will be mirrored. Clone mode is useful SW1 especially when users like

ملخص المحتوى في الصفحة رقم 8

Notes on Spare Drives using the Easy RAID Setting (EZ) When EZ function is ENABLED, the auto-rebuilding to spare drive is automatic. The degraded RAID group will start rebuilding automatically by using the existing spare drive. * Spare drive can be either plugged before RAID building or a new drive can be plug as the spare drive when RAID rebuild is required. A. Which port acts as a spare drive? The last drive will automatically become the spare drive. For a 3-drive RAID5 with spare: Drive